Eagle Post Code Definitions
D0  Check whether a hard or soft reset has occurred.
D1  Check Cache size,  Determine CPU speed.
D2  Disable Non Maskable Interrupt.
D3  Reset Video adapter.
D4  Disable L1 and L2 cache.  Initialize chipset.
D5  System validity check.  Calculate BIOS checksum.
D6  Initialize Keyboard controller.
D7  Flush keyboard input buffer.
D8  Issue command for keyboard to do a self-test.
D9  Retrieve 8042 Keyboard controller output buffer
DA  If Keyboard initialization fails, display message, halt.
DB  Initializes chipset after Keyboard Controller test pass
DF  Disables DMA controllers.
E0  Initialize PIC.  Reset CPU.
E1  Starts ref timer, Det SIMM type, Disables Mem Holes.
E2  Initialize timer channel 2 for speaker.
E3  Initialize System timer 0.
E4  Clear parity errors, reactivate parity.
E5  Enter flat memory mode.
E6  Test the first two megabytes of system memory.
E7  Generate minimum memory size and test memory.
E8  Try remapping SIMMs if failure detected.
E9  After test, clear parity, reactivate parity.
EA  Setup stack, Enable extended POST, Shadow block FE00.
EB  Decompress Dispatcher Initialization.
EC  Make F000 DRAM r/w enabled, Force EDI mode.
ED  Decompress System Bios.  
24  Initialize and load interrupt vectors.
0D  Load CMOS defaults from serial EEPROM.
0E  Check validity of CMOS.
0F  Load custom CMOS settings.
10  Set clock rate, setup Extended BIOs Data area.
25  Initialize Video rows.
F0  Reset cards in PCI slots.
F1  Enable and test extended NMI sources.
28  Set Video to monochrome mode.
29  Set Video to color display mode.
2A  Clear parity status.
2B  Custom video initialization.
2C  Test for optional video ROM.
2D  Initialize Video registers.
2F  Display memory Read/Write test.
30  Test Horizontal and Vertical tracing. Beep if no Video.
34  Display copyright message.
F3  Program the keyboard controller.
80  Keyboard and mouse detection.
81  8042 interface test.
F5  Initialize mouse if found.
39  Display setup message, keybrd and mouse detection msgs
43  Calculate memory size to be tested.
4F  Check if mem size is>0.  Zero all DRAM.  Test mem
52  Chipset adjusts the memory size.
61  Reset DMA controllers
62  Tests DMA registers.
65  Program DMA controllers.
66  Unmask timer and NMI.
8F  Setup floppy controller and interrupt.
92  Setup COM and LPT ports.
96  Give control to any option ROM.
9D  Set time and date.
A0  Check port base addresses.
A1  Check if keyboard has a stuck key.
A2  Reset Floating point unit.
AD  Update CMOS if FPU is present.
AE  Set typomatic rate.
AF  Read keyboard ID.
B0  Process POST errors.
A3  Display Setup and Boot options.
A7  Password is invalid.  The BIOS password is not used.
B1  Test Cache memory.
B3  Set Display Mode to 80x25.
B4  Jump to extended POST code in flash.
BB  APM, SMI initialization, Beep for boot.
00  Execute boot, Eagles and Kestrel Node 0.
B1  SMP tests. (Shared Multiprocessing)
B2  CNIC tests.
B3  Onboard SCSI Tests
B5  Onboard Ethernet tests
Kestrel Post Code Definitions
D0  Check whether a hard or soft reset has occurred.
D1  Check Cache size,  Determine CPU speed.
D2  Disable Non Maskable Interrupt.
D3  Reset Video adapter.
D4  Disable L1 and L2 cache.  Initialize chipset.
D5  System validity check.  Calculate BIOS checksum.
D6  Initialize Keyboard controller.
D7  Flush keyboard input buffer.
D8  Issue command for keyboard to do a self-test.
D9  Retrieve 8042 Keyboard controller output buffer
DA  If Keyboard initialization fails, display msg, halt.
DB  Initializes chipset after Kybd Controller test passes.
DF  Disables DMA controllers.
E0  Initialize PIC.  Reset CPU.
E1  Start ref timer, Det SIMM type, Disables Mem Holes.
E2  Initialize timer channel 2 for speaker.
E3  Initialize System timer 0.
E4  Clear parity errors, reactivate parity.
E5  Enter flat memory mode.
E6  Test the first two megabytes of system memory.
E7  Generate minimum memory size and test memory.
E8  Try remapping SIMMs if failure detected.
E9  After test, clear parity, reactivate parity.
EA  Setup stack, Enable extended POST, Shadow block FE00.
EB  Decompress Dispatcher Initialization.
EC  Make F000 DRAM r/w enabled, Force EDI mode.
ED  Decompress System Bios.  
24  Initialize and load interrupt vectors.
0D  Load CMOS defaults from serial EEPROM.
0E  Check validity of CMOS.
0F  Load custom CMOS settings.
10  Set clock rate, setup Extended BIOs Data area.
25  Initialize Video rows.
F0  Reset cards in PCI slots.
F1  Enable and test extended NMI sources.
28  Set Video to monochrome mode.
29  Set Video to color display mode.
2A  Clear parity status.
2B  Custom video initialization.
2C  Test for optional video ROM.
2D  Initialize Video registers.
2F  Display memory Read/Write test.
30  Test Horizontal and Vertical trace.Beep if no Video.
34  Display copyright message.
F3  Program the keyboard controller.
80  Keyboard and mouse detection.
81  8042 interface test.
F5  Initialize mouse if found.
39  Display setup message, keybrd and mouse detection msgs.
43  Calculate memory size to be tested.
4F  Check if memory size is>0. Zero all DRAM.Test memory
52  Chipset adjusts the memory size.
61  Reset DMA controllers
62  Tests DMA registers.
65  Program DMA controllers.
66  Unmask timer and NMI.
8F  Setup floppy controller and interrupt.
92  Setup COM and LPT ports.
96  Give control to any option ROM.
9D  Set time and date.
A0  Check port base addresses.
A1  Check if keyboard has a stuck key.
A2  Reset Floating point unit.
AD  Update CMOS if FPU is present.
AE  Set typomatic rate.
AF  Read keyboard ID.
B0  Process POST errors.
A3  Display Setup and Boot options.
A7  Password is invalid.  The BIOS password is not used.
B1  Test Cache memory.
B3  Set Display Mode to 80x25.
B4  Jump to extended POST code in flash.
BB  APM, SMI initialization, Beep for boot.
00  Execute boot.
B1  SMP tests. (Shared Multiprocessing)
B2  CNIC tests.
Eagle U numbers
D0  U151, U514, U301
D1  U681, U981, S241
D2  U521
D3  J422, U541, U741
D4  U541, U741, U551, U751, U562, U761
D5  U301
D6  U514, J407
D7  U514
D8  U514
D9  U514
DA  U514
DB  U514
DF  U521
E0  U151, U521, U681, U981
E1  U521, J181-J1053
E2  U521, U511, CR511
E3  U521
E4  U431, U432, U441, U444, U751, U761
E5  U431,432,441,444, J1052,1054,1152,1154,1023,1101,1200,1202
E6  U431,441,J1152,1154,1200,1202
E7  U431,441,J1154,1054,1101,1202
E8  U751, U761
E9  U751, U761
EA  U301, U751, U761
EB  U322, U321, U141, U211
EC  U301, U751, U761
ED  U322, U321, U141, U211, U301  
24  U514
0D  U302
0E  U302
0F  U301, U302
10  U301
25  U541, U741
F0  Reset cards in PCI slots.
F1  Enable and test extended NMI sources.
28  Set Video to monochrome mode.
29  Set Video to color display mode.
2A  Clear parity status.
2B  Custom video initialization.
2C  Test for optional video ROM.
2D  Initialize Video registers.
2F  Display memory Read/Write test.
30  Test Horizontal and Vertical trace.Beep if no Video.
34  Display copyright message.
F3  Program the keyboard controller.
80  Keyboard and mouse detection.
81  8042 interface test.
F5  Initialize mouse if found.
39  Display setup message, keybrd and mouse detect msgs.
43  Calculate memory size to be tested.
4F  Check if memory size is>0.Zero all DRAM.  Test mem
52  Chipset adjusts the memory size.
61  Reset DMA controllers
62  Tests DMA registers.
65  Program DMA controllers.
66  Unmask timer and NMI.
8F  Setup floppy controller and interrupt.
92  Setup COM and LPT ports.
96  Give control to any option ROM.
9D  Set time and date.
A0  Check port base addresses.
A1  Check if keyboard has a stuck key.
A2  Reset Floating point unit.
AD  Update CMOS if FPU is present.
AE  Set typomatic rate.
AF  Read keyboard ID.
B0  Process POST errors.
A3  Display Setup and Boot options.
A7  Password is invalid.  The BIOS password not used.
B1  Test Cache memory.
B3  Set Display Mode to 80x25.
B4  Jump to extended POST code in flash.
BB  APM, SMI initialization, Beep for boot.
00  Execute boot, Eagles and Kestrel Node 0.
B1  SMP tests. (Shared Multiprocessing)
B2  CNIC tests.
B3  Onboard SCSI Tests
B5  Onboard Ethernet tests
Kestrel Node 0 U numbers
D0  Check whether a hard or soft reset has occurred.
D1  Check Cache size,  Determine CPU speed.
D2  Disable Non Maskable Interrupt.
D3  Reset Video adapter.
D4  Disable L1 and L2 cache.  Initialize chipset.
D5  System validity check.  Calculate BIOS checksum.
D6  Initialize Keyboard controller.
D7  Flush keyboard input buffer.
D8  Issue command for keyboard to do a self-test.
D9  Retrieve 8042 Keyboard controller output buffer
DA  If Keyboard initialization fails, display msg, halt.
DB  Init chipset after Kybd Controller test passes.
DF  Disables DMA controllers.
E0  Initialize PIC.  Reset CPU.
E1  Starts ref timer,Det SIMM type,Disables Mem Holes.
E2  Initialize timer channel 2 for speaker.
E3  Initialize System timer 0.
E4  Clear parity errors, reactivate parity.
E5  Enter flat memory mode.
E6  Test the first two megabytes of system memory.
E7  Generate minimum memory size and test memory.
E8  Try remapping SIMMs if failure detected.
E9  After test, clear parity, reactivate parity.
EA  Setup stack, Enable ext POST, Shadow block FE00.
EB  Decompress Dispatcher Initialization.
EC  Make F000 DRAM r/w enabled, Force EDI mode.
ED  Decompress System Bios.  
24  Initialize and load interrupt vectors.
0D  Load CMOS defaults from serial EEPROM.
0E  Check validity of CMOS.
0F  Load custom CMOS settings.
10  Set clock rate, setup Extended BIOs Data area.
25  Initialize Video rows.
F0  Reset cards in PCI slots.
F1  Enable and test extended NMI sources.
28  Set Video to monochrome mode.
29  Set Video to color display mode.
2A  Clear parity status.
2B  Custom video initialization.
2C  Test for optional video ROM.
2D  Initialize Video registers.
2F  Display memory Read/Write test.
30  Test Horizontal and Vertical trace.Beep if no Video.
34  Display copyright message.
F3  Program the keyboard controller.
80  Keyboard and mouse detection.
81  8042 interface test.
F5  Initialize mouse if found.
39  Display setup message, keybrd and mouse detect msgs.
43  Calculate memory size to be tested.
4F  Check if memory size is>0.Zero all DRAM.  Test mem
52  Chipset adjusts the memory size.
61  Reset DMA controllers
62  Tests DMA registers.
65  Program DMA controllers.
66  Unmask timer and NMI.
8F  Setup floppy controller and interrupt.
92  Setup COM and LPT ports.
96  Give control to any option ROM.
9D  Set time and date.
A0  Check port base addresses.
A1  Check if keyboard has a stuck key.
A2  Reset Floating point unit.
AD  Update CMOS if FPU is present.
AE  Set typomatic rate.
AF  Read keyboard ID.
B0  Process POST errors.
A3  Display Setup and Boot options.
A7  Password is invalid.  The BIOS password not used.
B1  Test Cache memory.
B3  Set Display Mode to 80x25.
B4  Jump to extended POST code in flash.
BB  APM, SMI initialization, Beep for boot.
00  Execute boot, Eagles and Kestrel Node 0.
B1  SMP tests. (Shared Multiprocessing)
B2  CNIC tests.
Kestrel Node 1 U numbers
D0  Check whether a hard or soft reset has occurred.
D1  Check Cache size,  Determine CPU speed.
D2  Disable Non Maskable Interrupt.
D3  Reset Video adapter.
D4  Disable L1 and L2 cache.  Initialize chipset.
D5  System validity check.  Calculate BIOS checksum.
D6  Initialize Keyboard controller.
D7  Flush keyboard input buffer.
D8  Issue command for keyboard to do a self-test.
D9  Retrieve 8042 Keyboard controller output buffer
DA  If Keyboard initialization fails, display msg, halt.
DB  Init chipset after Kybd Controller test passes.
DF  Disables DMA controllers.
E0  Initialize PIC.  Reset CPU.
E1  Starts ref timer,Det SIMM type,Disables Mem Holes.
E2  Initialize timer channel 2 for speaker.
E3  Initialize System timer 0.
E4  Clear parity errors, reactivate parity.
E5  Enter flat memory mode.
E6  Test the first two megabytes of system memory.
E7  Generate minimum memory size and test memory.
E8  Try remapping SIMMs if failure detected.
E9  After test, clear parity, reactivate parity.
EA  Setup stack, Enable ext POST, Shadow block FE00.
EB  Decompress Dispatcher Initialization.
EC  Make F000 DRAM r/w enabled, Force EDI mode.
ED  Decompress System Bios.  
24  Initialize and load interrupt vectors.
0D  Load CMOS defaults from serial EEPROM.
0E  Check validity of CMOS.
0F  Load custom CMOS settings.
10  Set clock rate, setup Extended BIOs Data area.
25  Initialize Video rows.
F0  Reset cards in PCI slots.
F1  Enable and test extended NMI sources.
28  Set Video to monochrome mode.
29  Set Video to color display mode.
2A  Clear parity status.
2B  Custom video initialization.
2C  Test for optional video ROM.
2D  Initialize Video registers.
2F  Display memory Read/Write test.
30  Test Horizontal and Vertical trace.Beep if no Video.
34  Display copyright message.
F3  Program the keyboard controller.
80  Keyboard and mouse detection.
81  8042 interface test.
F5  Initialize mouse if found.
39  Display setup message, keybrd and mouse detect msgs.
43  Calculate memory size to be tested.
4F  Check if memory size is>0.Zero all DRAM.  Test mem
52  Chipset adjusts the memory size.
61  Reset DMA controllers
62  Tests DMA registers.
65  Program DMA controllers.
66  Unmask timer and NMI.
8F  Setup floppy controller and interrupt.
92  Setup COM and LPT ports.
96  Give control to any option ROM.
9D  Set time and date.
A0  Check port base addresses.
A1  Check if keyboard has a stuck key.
A2  Reset Floating point unit.
AD  Update CMOS if FPU is present.
AE  Set typomatic rate.
AF  Read keyboard ID.
B0  Process POST errors.
A3  Display Setup and Boot options.
A7  Password is invalid.  The BIOS password not used.
B1  Test Cache memory.
B3  Set Display Mode to 80x25.