   Banyan Vines DOS workstations (NDIS)
  
  This document applies to the EtherExpress(tm) 16, 16TP, 16C, FLASH,
  FLASH TP, FLASHC, MCA, and MCA/TP adapters.  It contains installation 
  notes for installing the NDIS driver.  It does not explain how to 
  configure an EtherExpress adapter.  For instructions about configuring 
  the adapter, see the printed installation guide.

  
  INTRODUCTION
  ------------
  This document contains information relating to Banyan* Vines* releases
  4.00(0), 4.00(1), 4.00(2), and 4.10.
  
  The EtherExpress network adapters communicate with Banyan Vines via an
  NDIS driver supplied on the EtherExpress diskette.  Vines versions 4.00(x)
  require a patch from Banyan to talk to an NDIS driver.  Version 4.10 has
  this patch included.
  
  For information about these patches call your Banyan Vines representative
  and ask for Banyan Vines Bulletin #200 dated 9/1/91.
  
  The patch for versions 4.00(0) and 4.00(1) is called NEW REV 1Y.  The
  patch for version 4.00(2) is called NEW REV patch 2NNN.
  
  NEW REV patch 2NNN contains four files:
  -  NDISBAN.COM  The VINES NDIS driver
  -  NDISBAN.DOC  An ASCII file with driver installation instructions
  -  PROTMAN.DOS  Version 1.1 of the protocol manager
  -  NETBIND.EXE  Starts Protman
  
  NOTE:     The version of TCP/IP supplied with Banyan Vines 4.X does not
            support NDIS drivers.  To use TCP/IP with an NDIS driver, you
            will need to purchase a version of TCP/IP that supports NDIS. 
            We recommend you call your Banyan support representative for
            more information.
  
  The rest of this document is installation notes on how to install the
  EtherExpress NDIS driver with Banyan Vines 4.00(2).
  
  PROCEDURE FOR A VINES 4.00(2) WORKSTATION
  -----------------------------------------
  1.   You will need the I/O address and IRQ of the EtherExpress card.  Boot
       your computer from a DOS diskette.  
  
       EtherExpress 16: Run SOFTSET and choose View Configuration.
  
       EtherExpress MCA: Run the System Configuration utility and choose
       View Configuration.
  
  2.   From a workstation already on the network, install the NDIS patch on
       your server(s).  The NDIS support files will be copied onto the
       Z:\PCINIT subdirectory of your server.
  
       NOTE:     This patch should be on a server that is within one hop of
                 the workstation.
  
  3.   Read the NDISBAN.DOC file in the Z:\PCINIT subdirectory of your
       server.  This readme file was supplied with the NDIS patch.
  
  4.   Follow Banyan's instructions for creating a boot disk.  (You must be
       using DOS 3.1 or newer.)
  
  5.   Run PCCOPY from the Z drive of the server.
  
  6.   When PCCOPY prompts you to select a LAN adapter, select "NDIS
       Ethernet."  PCCOPY will copy the appropriate files to your boot disk.
  
  7.   On your boot disk, create a A:\LANMAN subdirectory.
  
  8.   From the EtherExpress diskette, copy \VINES\PROTOCOL.INI file to the
       new \LANMAN directory on the boot disk.
  
       DO NOT specify the IRQ level in the PROTOCOL.INI file.  However, if
       the EtherExpress adapter is set to use an I/O address other than 
       300h, edit the PROTOCOL.INI and change the IOADDRESS=300 to the correct 
       I/O address.
  
  9.   Copy \NDIS\EXP16.DOS from the EtherExpress diskette to the root
       directory of the boot diskette.  Verify that the root directory also
       contains BAN.EXE.
  
  10.  From the boot disk, run PCCONFIG and select "NDIS Ethernet."  Choose
       the IRQ that matches the configuration of the EtherExpress board. 
       When PCCONFIG prompts for "Bindings =", enter EXP16.
  
  11.  Before exiting PCCONFIG, save the configuration.
  
  12.  Add these two lines to your CONFIG.SYS file:
       Device=PROTMAN.DOS
       Device=EXP16.DOS
  
  13.  Using this boot disk, reboot the workstation.  The workstation will
       logon to the network.
  
  
* Third-party trademarks are the property of their respective owners.
