----------------------------------------------------------------------------
  	   Installing FDDI Device Drivers on SCO Operating Systems
----------------------------------------------------------------------------

This directory contains the following files:

README.TXT   - This file.
CUSTOM.DST   - Driver installation file used by SCO OpenServer 5.0.
FXSCOLLI.TAZ - Driver installation file used by SCO UNIX/Open Desktop



Section 1  INSTALLING THE FDDI DEVICE DRIVER ON SCO OPEN SERVER
---------------------------------------------------------------

Driver Revision: 	v3.2.0a
Specification Revision:	MDI Version 1.0

Software Requirements:

	SCO OpenServer v5.0.2
	SCO Advanced Hardware Supplement v5.2.0

Hardware Requirements:

	One or more (up to 8) of the following adapters -

		DEC FDDIcontroller/EISA (All models and revisions)
		DEC FDDIcontroller/PCI  (All models and revisions)

To install the driver off floppy:

	1. Make sure this floppy is in drive.
	2. Run custom(ADM) utility and select "Software", 
	   followed by "Install New...".
	3. When prompted, select the local host machine to
	   install from.
	4. When prompted, select Floppy Disk Drive 0 as the
	   media device.
	5. When prompted for installation preference, select
	   "Full".

The driver files will be copied and installed on your system.
Select "Host" followed by "Exit" to leave the utility.


To add adapter hardware:

	1. Be sure that driver is already installed.
	2. Run netconfig(ADM) utility and select "Hardware",
	   followed by "Add new LAN adapter".
	3. When prompted, select the Digital FDDI controller to
	   install.
	4. When prompted, select the networking product (protocol
	   stack) to add to the adapter.
	5. Configure the networking product as needed.  If
           configuring TCP/IP, you must select "Advanced Options..."
           from the SCO TCP/IP Configuration menu, then change
           the Frame Format from Ethernet-II to 802.n.
	6. Select "OK" to leave the networking product configuration
	   menu and return to the main menu.
	7. Select the Digital FDDI controller you just configured, then
	   select "Hardware" followed by "Modify hardware configuration".
	8. When the Network Driver Configuration menu appears, select
	   "Advanced Options...".
	9. Change the Source Routing Support keyword from "auto" to "none".
	   This will disable source routing and allow your networking
	   protocol to function properly.
       10. Select "OK" to leave the network driver configuration menu and
	   return to the main menu.
       11. Select "Hardware" followed by "Exit" to leave the utility.  When
	   prompted, relink the kernel, then reboot the system to load the
	   new driver.



Section 2  INSTALLING THE FDDI DEVICE DRIVER ON SCO UNIX/OPEN DESKTOP
---------------------------------------------------------------------

Driver Revision: 	v2.0.0a
Specification Revision:	LLI Version 3.1 Revision 2

Software Requirements:

	SCO UNIX System V/386 Release 3.2v4.2, or later
	SCO Open Desktop 3.0

Hardware Requirements:

	One or more (up to 8) of the following adapters -

		DEC FDDIcontroller/EISA (All models and revisions)
		DEC FDDIcontroller/PCI  (All models and revisions)

To install the driver off floppy:

	1. Make sure this floppy is in drive.
	2. Copy the A:\SCO\FXSCOLLI.TAZ file to the UNIX partition using
           the doscp(C) command or DOS Merge.  Rename, uncompress, and
           extract the file to a UNIX formatted 3 1/2" floppy using the
           following commands:

		# mv FXSCOLLI.TAZ fxscolli.tar.Z
		# uncompress fxscolli.tar.Z
		# dd if=fxscolli.tar of=/dev/rfd0135ds18 bs=18k

	3. Run the custom(ADM) utility to install the driver off the newly
	   created UNIX driver floppy.
	4. Run the netconfig(ADM) utility for each adapter to be configured
	   into the system.

To extract driver release notes:

Enter the following commands to extract the driver release notes from 
the UNIX formatted floppy and display them:

	# cd /
	# tar xvf /dev/rfd0 ./usr/lib/dfx/rel_inst.notes
	# cd /usr/lib/dfx
	# more rel_inst.notes

The driver release notes file contains additional installation and
configuration information for this driver.
