a:\wfw\readme.txt                       28-SEP-1995


This README.TXT file is for the installation of Digital Equipment 
Corporation's DEC FDDIcontroller/PCI adapters in a Windows for 
Workgroup environment.

Supported adapters for real mode (NDIS2):
	DEFPA
Supported adapters for enhanced mode (NDIS3): 
	none
Supported adapters for ODI:
	DEFPA (with restrictions, see DRIVER TYPES section)

Device drivers: DEFPA.DOS

This document contains the following sections:

	1. Installation Troubleshooting
	2. Driver Types
	3. Adding the Adapter After WFW 3.11 Installation
	4. Adding the Adapter During WFW 3.11 Installation


********************************
* INSTALLATION TROUBLESHOOTING *
********************************

Important note: If this is not your first network installation in 
WFW, you may have a problem with old information still being in the 
setup files, causing functional problems.  If you are experiencing 
problems, go to Network Setup and select "No Network".  Restart the 
system. Examine the setup files (config.sys, win.ini, protocol.ini, 
system.ini) and make sure that no references to network adapters 
exists.  From the root, type the following command:

	dir \windows\system\oem*

Examine these .inf files and if any of them are pertinent to old
installations of network adapters, delete them. Delete old versions 
of network adapter drivers (DEFPA.DOS).  
Then go back into Network Setup and add your network adapters
normally.


**************** 
* DRIVER TYPES *
****************

When installing the adapter, only the NDIS2 driver (real mode) is 
supported.

The NDIS 3 driver (enhanced mode) is not available for this adapter.

The DOS ODI driver is available.  However, Windows for Workgroups does 
not install FDDI DOS ODI client drivers properly.  Also, Novell's ODINSUP
shim does not support FDDI DOS ODI client drivers, so you cannot run
NDIS 2 compliant protocol stacks over the DOS ODI driver.  For more
information on DOS ODI driver installations under WFW 3.11, consult
\NOVELL\DOSODI\README.TXT.


**************************************************
* ADDING THE ADAPTER AFTER WFW 3.11 INSTALLATION *
**************************************************

Make sure your adapter is configured in the system.
Automatic Installation Using the Network Setup Program:

      1. Click on the Network Setup icon.
	 If no network is installed, click on Networks button,
	 choose network type, then click OK.

      2. Click on the Drivers button.

      3. If a driver for this adapter already exists, you must 
	 remove it first by clicking on the driver name to select 
	 the driver, then clicking the remove button.

      4. Click the Add Adapter button and select Unlisted or 
	 Updated Network Adapter.

      5. Insert the driver diskette in the floppy drive and press 
	 <ENTER> to accept the A:\ path.
	      
      6. Choose the appropriate adapter and click OK.  Click the 
	 Setup button.  See the "Driver Types" section of this 
	 readme for information on choosing the appropriate driver 
	 for your application.

      7. Follow the instructions to complete the software 
	 installation and reset or power cycle your computer when 
	 WFW asks you to restart.


***************************************************
* ADDING THE ADAPTER DURING WFW 3.11 INSTALLATION *
***************************************************

The installation kit for Windows for Workgroups comprises eight 
diskettes.  Continue with the WFW3.11 installation of disks 1-6.  
During the installation of diskette #7, the network environment 
will be configured.  At this point you will be asked to select a
Network Adapter to install.

Below is a sample of an installation.
							
	1. Select the Bullet "Install Microsoft Windows Network"
	   Click OK
	   Click Continue

	2. From the Add Network Adapter Screen...
	   Select "Unlisted or Updated Network Adapter" , click OK

	3. From Install Driver Screen...
	   - Remove disk #7
	   - Insert the network adapter driver diskette
	     NOTE:  DO NOT INCLUDE THE FILENAME AS PART OF THE PATH
	   Click OK to accept the A:\ path

	4. From Unlisted or updated Network Adapter Screen...
	   Select the appropriate adapter and click OK.  Click the 
	   Setup button.  See the "Driver Types" section of this 
	   readme for information on choosing the appropriate 
	   driver for your application.

	5. From Microsoft Windows Network Name screen...
	   Enter your site specific information and click OK

	6. From Install Driver Screen...
	   - Remove network adapter driver diskette
	   - Insert Disk #7 an click OK
	   - Remove Disk #7
	   - Insert Disk #8

	7. From Install Driver Screen...
	   - Remove Disk #8
	   - Insert network adapter driver diskette

	8. From Networks Screen...
	   Enter A:\
	   - Remove network adapter driver diskette
	   - Insert Disk #8

	9. From Install Driver Screen...
	   Click OK

	10. Finish Installation 

*** Note POWER OFF/ON your PCI based PC after the install.

