
TYAN COMPUTER CORPORATION

S1363-004 (Rev. 1.0)

  Data bus:                  32-bit PCI

  Size:                      Half-length, Full-height card

  Hard drive supported:      Four Enhanced IDE (AT) interface drives

  Floppy drives supported:   Two 360KB, 720KB, 1.2MB, or 1.44MB drives

[Image]

                                CONNECTIONS

                   Function                             Location

  25-pin parallel port - external                         CN1

  9-pin serial port - external                            CN2

  10-pin serial port - internal                           CN3

  16-pin game port - internal                             CN4

  34-pin primary control cable connector -                CN5
  floppy drive

  40-pin primary IDE (AT) interface connector             CN6

  40-pin secondary IDE (AT) interface                     CN7
  connector

  4-pin connector - drive active LED                      CN8

  40-pin connector - paddle card                          PDL1

                        USER CONFIGURABLE SETTINGS

                Function                      Location         Setting

     Floppy drive disk change signal            J0             open
      not intercepted

      Floppy drive disk change being             J0            closed
      intercepted

     Fixed I/O address                          J1            closed

      Relocatable I/O address                    J1             open

     Secondary IDE (AT) channel IRQ to          J4            closed
      ISA IRQ15

      No secondary IDE (AT) channel IRQ          J4             open
      to ISA IRQ15

     Primary IDE (AT) channel legacy            J5            closed
      IRQ to ISA IRQ14

      No primary IDE (AT) channel                J5             open
      legacy IRQ to ISA IRQ 14

     No buffered secondary IDE (AT)             J6             open
      legacy IRQ to IRQ15

      Buffered secondary IDE (AT)                J6            closed
      legacy IRQ to IRQ15

     No buffered primary IDE (AT)               J7             open
      legacy IRQ to IRQ14

      Buffered primary IDE (AT) legacy           J7            closed
      IRQ to IRQ14

     Factory configured - do not alter          J8              N/A

     Factory configured - do not alter          J9              N/A

     Factory configured - do not alter         J10              N/A

     Native mode IDE (AT) IRQ not used         J11             open

      Native mode IDE (AT) IRQs to PCI         J11            closed
      INTA

     Factory configured - do not alter         J90              N/A

     Floppy drive order A:, B: normal     P1/pins 2 & 3       closed

      Floppy drive order A:, B:            P1/pins 1 & 2       closed
      exchange

     Floppy controller I/O address is     P2/pins 2 & 3       closed
      3F0h

      Floppy controller I/O address is     P2/pins 1 & 2       closed
      370h

     Floppy controller enabled            P3/pins 2 & 3       closed

      Floppy controller disabled           P3/pins 1 & 2       closed

     Factory configured - do not alter         P10              N/A

     Factory configured - do not alter         P11              N/A

     Factory configured - do not alter          T1              N/A

     IRQ4 for serial port 1                     T4            closed

      No interrupt for serial port 1             T4             open

     IRQ3 for serial port 2                     T5            closed

      No interrupt for serial port 2             T5             open

     ISA (AT) uni-directional printer           T6             open
      port mode

      PS2 bi-directional compatible              T6            closed
      mode

     Game port enabled                          T7            closed

      Game port disabled                         T7             open

                    USER CONFIGURABLE SETTINGS (CONT)

               Function                     Location           Setting

     Factory configured - do not              T8                N/A
      alter

     Factory configured - do not              T9                N/A
      alter

     Factory configured - do not              T10               N/A
      alter

     Factory configured - do not              T11               N/A
      alter

            ACCESS IDE (AT) CHANNELS I/O ADDRESS CONFIGURATION

           Setting                     J2                     J3

            Enabled                  open                  closed

             Disabled                closed                  open

                        PARALLEL PORT CONFIGURATION

            Port                       P8                     P9

        1 (378h - 37Fh)       pins 2 & 3 closed      pins 2 & 3 closed

         2 (278h - 27Fh)       pins 1 & 2 closed      pins 1 & 2 closed

         3 (3BCh - 3BEh)       pins 1 & 2 closed      pins 2 & 3 closed

            Disabled           pins 2 & 3 closed      pins 1 & 2 closed

                        SERIAL PORT 1 CONFIGURATION

             COM                       P4                     P5

          COM1 (3F8h)         pins 2 & 3 closed      pins 2 & 3 closed

           COM3 (3E8h)         pins 1 & 2 closed      pins 1 & 2 closed

           COM4 (2E8h)         pins 2 & 3 closed      pins 1 & 2 closed

            Disabled           pins 1 & 2 closed      pins 2 & 3 closed

                        SERIAL PORT 2 CONFIGURATION

             COM                       P6                     P7

          COM2 (2F8h)         pins 2 & 3 closed      pins 2 & 3 closed

           COM3 (3E8h)         pins 2 & 3 closed      pins 1 & 2 closed

           COM4 (2E8h)         pins 1 & 2 closed      pins 1 & 2 closed

            Disabled           pins 1 & 2 closed      pins 2 & 3 closed

                     PARALLEL PORT INTERRUPT SELECTION

             IRQ                       T2                     T3

               7                    closed                  open

                5                     open                  closed

             Disabled                 open                   open

               SERIAL PORTS ADVANCED INTERRUPT CONFIGURATION

      Port 1           Port 2          T3           T4            T5

        IRQ4           IRQ3          open        closed        closed

         IRQ3           IRQ4          open        pin 1 to      pin 2 to
                                                 T5/pin 1      T4/pin 2

         IRQ5           IRQ3          open        pin 1 to      pin 1 to
                                                 T5/pin 1      T4/pin 1

         IRQ4           IRQ5        pin 2 to      pin 2 to      closed
                                    T4/pin 2     T3/pin 2

         IRQ4         Disabled        open        closed         open
                        IRQ3

        Disabled        IRQ3          open         open         closed
         IRQ4

        Disabled        IRQ4          open        pin 2 to      pin2 to
         IRQ3                                    T5/pin 2      T4/pin 2

        Disabled        IRQ5        pin 2 to      pin 2 to       open
         IRQ4                       T4/pin 2     T3/pin 2

                       MISCELLANEOUS TECHNICAL NOTES

  Note: In order to utilize the S1366s IDE and I/O functions, the S136x
  paddle card must be installed on connector PDL1.

