
ACCULOGIC, INC.

SIDE-4/HP

  Data bus:                  16-bit ISA

  Size:                      Half-length, full-height card

  Hard drive supported:      Two IDE(AT) interface drives

  Floppy drives supported:   Two 360KB, 720KB, 1.2MB, 1.44MB or 2.88MB
                             drives

[Image]

                        CONNECTIONS

                Function                      Location

  34-pin cable connector - floppy drive          J5

  40-pin IDE(AT) connector                       J6

  10-pin serial port 2 - internal                J7

  9-pin serial port 1 - external                 J9

  25-pin parallel port - external               J10

  4-pin connector - drive active LED            J12

  Internal power connector                      J13

                        USER CONFIGURABLE SETTINGS

              Function                    Location           Setting

     IDE primary address enabled           JP2             Pins 2 & 3
                                                              closed

      IDE secondary address is              JP2             Pins 1 & 2
      170h                                                    closed

     IDE(AT) interface enabled             JP3             Pins 1 & 2
                                                              closed

      IDE(AT) interface disabled            JP3             Pins 2 & 3
                                                              closed

     Factory configured - do not           JP6                N/A
      alter

     Factory configured - do not           JP7                N/A
      alter

     Floppy primary address                JP9             Pins 2 & 3
      enabled                                                 closed

      Floppy secondary address              JP9             Pins 1 & 2
      enabled                                                 closed

      Floppy secondary address              JP9             Pins 1 & 2
      enabled                                                 closed

                  USER CONFIGURABLE SETTINGS (CONTINUED)

              Function                    Location           Setting

     Factory configured - do not           JP11               N/A
      alter

     Factory configured - do not           JP12               N/A
      alter

     Floppy drive interface                JP15            Pins 1 & 2
      enabled                                                 closed

      Floppy drive interface                JP15            Pins 2 & 3
      disabled                                                closed

     Parallel port IRQ 7 select            JP16            Pins 1 & 2
                                                              closed

      Parallel port IRQ 5 select            JP16            Pins 2 & 3
                                                              closed

     IOCHRDY signal disabled               JP17               Open

      IOCHRDY signal enabled                JP17              Closed

      IDE(AT) IRQ 15 select -               JP18            Pins 1 & 2
      normal                                                  closed

      IDE(AT) IRQ15 select -                JP18            Pins 2 & 3
      delayed                                                 closed

     IDE(AT) IRQ 14 select -               JP19            Pins 1 & 2
      normal                                                  closed

      IDE(AT) IRQ14 select -                JP19            Pins 2 & 3
      delayed                                                 closed

     Serial port 1 IRQ4 select             JP22            Pins 1 & 2
                                                              closed

     Serial port 2 IRQ3 select             JP22            Pins 3 & 4
                                                              closed

  Note: The location of jumper JP17 is unidentified. It may be soldered
  on the board in some models.

                      SERIAL PORT 1 ADDRESS SELECTION

             COM                       JP8                   JP14

          COM1 (3F8h)          Pins 1 & 2 closed      Pins 1 & 2 closed

           COM2 (2F8h)          Pins 1 & 2 closed      Pins 2 & 3 closed

           COM3 (2F8h)          Pins 2 & 3 closed      Pins 1 & 2 closed

             Disabled           Pins 2 & 3 closed      Pins 2 & 3 closed

                      SERIAL PORT 2 ADDRESS SELECTION

             COM                      JP10                   JP13

          COM2 (2F8h)          Pins 1 & 2 closed      Pins 1 & 2 closed

           COM1 (3F8h)          Pins 1 & 2 closed      Pins 2 & 3 closed

           COM4 (238h)          Pins 2 & 3 closed      Pins 1 & 2 closed

             Disabled           Pins 2 & 3 closed      Pins 2 & 3 closed

                      PARALLEL PORT ADDRESS SELECTION

              LPT                       JP4                   JP5

           LPT1(378h)           Pins 1 & 2 closed     Pins 2 & 3 closed

            LPT2(278h)           Pins 1 & 2 closed     Pins 1 & 2 closed

             Disabled            Pins 2 & 3 closed     Pins 2 & 3 closed

             PARALLEL PORT DMA SELECTION

   Channel           JP20                JP21

      1        Pins 1 & 2 closed   Pins 1 & 2 closed

      3        Pins 2 & 3 closed   Pins 2 & 3 closed

             MISCELLANEOUS TECHNICAL NOTES

  Location of pin 1 on all jumpers is not available.

