
PINE TECHNOLOGY

PT-606E

Card Type                  Controller card
Maximum Onboard Memory     Unidentified
Hard Drives supported      Two IDE (AT) drives
Floppy drives supported    Two 360KB, 720KB, 1.2MB, or 1.44MB drives
I/O Options                Floppy drive interface, game port, IDE
                           interface (2), parallel port, serial ports (2)
Data Bus                   16-bit ISA
Card Size                  Half-length, full-height

[Image]

                                CONNECTIONS

         Function          Label             Function              Label

  40-pin secondary          CN1     10-pin serial port 2 -          CN6
  IDE(AT) connector                 internal

  40-pin primary IDE(AT)    CN2     25-pin parallel port -          CN7
  connector                         external

  34-pin cable connector    CN3     2-pin connector - primary       JP6
  - floppy drive                    IDE drive active LED

  9-pin serial port 1 -     CN4     2-pin connector -               JP7
  external                          secondary IDE drive active
                                    LED

  16-pin game port -        CN5
  internal

                        USER CONFIGURABLE SETTINGS

                 Function                    Label         Position

     Game port enabled                       J1       Pins 1 & 2 closed

      Game port disabled                      J1       Pins 2 & 3 closed

     Floppy drive interface enabled          J3       Pins 1 & 2 closed

      Floppy drive interface disabled         J3       Pins 2 & 3 closed

     Primary IDE enabled                     J5       Pins 1 & 2 closed

      Primary IDE disabled                    J5       Pins 2 & 3 closed

     Secondary IDE enabled                   J6       Pins 1 & 2 closed

      Secondary IDE disabled                  J6       Pins 2 & 3 closed

     External floppy enabled                 J12      Pins 1 & 2 closed

      External floppy disabled                J12      Pins 2 & 3 closed

     ECP enabled                             J13      Pins 1 & 2 closed

      ECP disabled                            J13      Pins 2 & 3 closed

     Factory configured - do not alter       J14      Pins 1 & 2 closed

     Factory configured - do not alter       J17        Unidentified

     IOCHRDY signal enabled                  JP3           Closed

      IOCHRDY signal disabled                 JP3            Open

     IDE channels use same IDE LED           JP5           Closed

      IDE channels use separate IDE LEDs      JP5            Open

                      PARALLEL PORT ADDRESS SELECTION

                Setting                                 J4

                LPT1 (378h)                     Pins 1 & 2 closed

                 LPT2 (278h)                     Pins 2 & 3 closed

                       SERIAL PORT ADDRESS SELECTION

     Setting          J7             J8            J9            J10

   COM1 (3F8h)     Pins 1 & 2    Pins 1 & 2        N/A           N/A
                    closed         closed

   COM2 (2F8h)        N/A           N/A         Pins 1 & 2    Pins 1 & 2
                                                 closed         closed

   COM3 (3E8h)     Pins 1 & 2    Pins 2 & 3        N/A           N/A
                    closed         closed

   COM4 (2E8h)        N/A           N/A         Pins 1 & 2    Pins 2 & 3
                                                 closed         closed

    Disabled       Pins 2 & 3       N/A         Pins 2 & 3       N/A
                    closed                       closed

                        INTERRUPT SELECTION

      IRQ (Send)           IRQ (Receive)               JP4

           3                     3             Pins 11 & 12 closed

           3                     4             Pins 10 & 11 closed

           4                     3              Pins 8 & 9 closed

           4                     4              Pins 7 & 8 closed

           5                     3              Pins 5 & 6 closed

           5                     4              Pins 4 & 5 closed

           9                     3              Pins 2 & 3 closed

           9                     4              Pins 1 & 2 closed

                       PARALLEL PORT MODE SELECTION

         Setting                    J2                      J11

            SPP             Pins 2 & 3 closed       Pins 1 & 2 closed

             ECP             Pins 1 & 2 closed       Pins 1 & 2 closed

             EPP             Pins 1 & 2 closed       Pins 2 & 3 closed

                            DACK/DRQ SELECTION

      Setting           DACK        DRQ          J15             J16

          SPP          N/A         N/A       Pins 5 & 6      Pins 1 & 2
                                                closed         closed

         ECP/EPP         3           1        Pins 1 & 2      Pins 3 & 4
                                                closed         closed

         ECP/EPP         3           3        Pins 3 & 4      Pins 5 & 6
                                                closed         closed

