
ADVANCED INTERLINK CORPORATION

ANET-1

NIC Type      ARCnet
Transfer Rate 2.5Mbps
Data Bus      8-bit ISA
Topology      Star

              Linear Bus
Wiring Type   RG-62A/U 93ohm coaxial
Boot ROM      Available

[Image]

                               NODE ADDRESS

  Node   SW1/1    SW1/2   SW1/3   SW1/4    SW1/5   SW1/6    SW1/7   SW1/8

   0       -       -        -       -       -        -       -        -

   1      Off      On      On      On       On      On       On      On

   2      On      Off      On      On       On      On       On      On

   3      Off     Off      On      On       On      On       On      On

   4      On       On      Off     On       On      On       On      On

  251     Off     Off      On      Off     Off      Off     Off      Off

  252     On       On      Off     Off     Off      Off     Off      Off

  253     Off      On      Off     Off     Off      Off     Off      Off

  254     On      Off      Off     Off     Off      Off     Off      Off

  255     Off     Off      Off     Off     Off      Off     Off      Off

  Note:Node address 0 is used for messaging between nodes and must not be
  used.

       A total of 255 node address settings are available. The switches
       are a binary representation of the decimal node addresses. Switch
       1 is the Least Significant Bit and switch 8 is the Most
       Significant Bit. The switches have the following decimal values:
       switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the
       switches and add the values of the off switches to obtain the
       correct node address. (On=0, Off=1)

                             DIAGNOSTIC LED(S)

         LED                  Status                   Condition

        LED1                    On             Data is being transmitted

        LED1                    On                 Data is not being
                                                      transmitted

        LED2                    On              Data is being received

        LED2                    On            Data is not being received

                            COMPATABILITY MODE

                Setting                                JP1

                Normal mode                Pins 1 & 6, pins 2 & 3, and
                                                pins 4 & 5 closed.

                Special mode                Pins 1 & 2, pins 3 & 4, and
                                                pins 5 & 6 closed.

       Note:Special compatibility mode is used when using a VGA or EGA
       display, an EMS expansion card, and/or an RLL or ESDI HD
       controller on some systems. This mode forces the card to use 16KB
       of memory, rather than 32KB of memory, between addresses CC000h
       and CFFFFh.

                            BASE MEMORY ADDRESS

     Address        JP2A      JP2B        JP2C        JP2D        JP2E

       C0000h       Open      Open       Closed      Closed      Closed

       C8000h       Open      Open       Closed      Closed       Open

       CC000h       Open      Open       Closed       Open        Open

      D0000h       Open      Open       Closed       Open       Closed

       D8000h       Open      Open       Closed       Open        Open

  Note:Address CC000h must be used if Special compatibility mode is
  sbeing used.

                             I/O BASE ADDRESS

   Address     JP3A     JP3B       JP3C      JP3D       JP3E       JP3F

      260h     Open    Closed     Closed     Open       Open      Closed

      280h     Open    Closed      Open     Closed     Closed     Closed

     2E0h     Open    Closed      Open      Open       Open      Closed

      2F0h     Open    Closed      Open      Open       Open       Open

      300h     Open     Open      Closed    Closed     Closed     Closed

      360h     Open    Closed      Open      Open       Open      Closed

                             INTERRUPT REQUEST

    IRQ         JP4A         JP4B        JP4C         JP4D        JP4E

       2      Closed        Open        Open         Open        Open

        3       Open        Closed       Open         Open        Open

        4       Open         Open       Closed        Open        Open

        5       Open         Open        Open        Closed       Open

        7       Open         Open        Open         Open       Closed

                     RESPONSE/RECONFIGURATION TIMEOUTS

  Response Time     Reconfiguration Time        J5A              J5B

      74.7s               840ms                Open            Open

     283.4s               1680ms               Open           Closed

     561.8 s              1680ms              Closed           Open

     1118.6s              1680ms              Closed          Closed

  Note:All NICs on the network must have this option set the same.

