
RACORE COMPUTER PRODUCTS, INC.

M8117

NIC Type          Token-Ring
Transfer Rate     4/16Mbps
Data Bus          8/16-bit ISA
Topology          Ring
Wiring Type       Shielded twisted pair

                  Unshielded twisted pair(with external media filter)

                  62.5/125 or 50/125 m
Boot ROM          Available

[Image]

                                 MAU TYPE

                 Setting                                JP2

                  802.5J                        Pins 2 & 3 closed

                  Alternate                      Pins 1 & 2 closed

                             ROM MEMORY ENABLE

                 Setting                                JP3

                  Enabled                            Closed

                   Disabled                            Open

  Note:The boot ROM socket can contain a BIA ROM or a boot ROM. The BIA
  ROM provides the node address if a boot ROM is not installed. If the
  ROM memory is disabled, the node address must be set using the
  RTR16ASI.SYS device driver.

                             I/O BASE ADDRESS

          Address                    SW1/1                  SW1/2

          A00 - A0Fh                 On                      On

           A20 - A2Fh                 Off                     On

           A40 - A4Fh                 On                     Off

           A60 - A6Fh                 Off                    Off

                             INTERRUPT REQUEST

            IRQ                     SW1/3                   SW1/4

              2/9                    Off                     On

              3                     On                      On

              10                     On                      Off

              11                     Off                     Off

  Note:If using the card in an 8-bit slot, do not use IRQ10 or IRQ11.

                             BOOT ROM ADDRESS

           Address                    SW1/5                 SW1/6

          CC000 - CDFFFh               On                     On

          D0000 - D1FFFh               Off                    On

          D8000 - D9FFFh               On                    Off

         DC000 - DDFFFh               Off                   Off

                                DMA CHANNEL

          Channel                   SW1/7                   SW1/8

              DMA0                    On                     On

              DMA5                   Off                     On

             DMA6                    On                     Off

              DMA7                   Off                     Off

                                 BOOT ROM

                 Setting                               SW1/9

                  Disabled                              On

                   Enabled                              Off

  Note:To install the boot ROM remove the BIA ROM (if installed) and
  replace it with the boot ROM.

  JP3 must be closed for the boot ROM to function.

                           NETWORK SEGMENT SPEED

                 Speed                                SW1/10

                  16Mbps                               On

                   4Mbps                               Off

  Note:All cards on the network segment must have this option set the
  same.

                     LOGIC LINK CONTROL (LLC) LOCATION

                 Speed                                SW1/11

                 ROM based                             On

                  RAM based                            Off

  Note:LLC allows the card to access networks using the ISO and SNA
  protocols. (e.g. IBM PC LAN,IBM 3270 terminal emulation, and AS400)

  The card has built-in LLC support on the two ROMs above SW1. To allow
  for future compatiblity and upgrades you can load the LLC code into the
  onboard RAM.

                     CABLE TYPE & MAXIMUM CABLE LENTGH

                Type                     Max. Length          SW1/12

           Fiber optic cable                75m                On

          Shielded twisted pair             2000m               Off

       Unshielded twisted pair with          100m               Off
               media-filter

                             DIAGNOSTIC LED(S)

       LED               Status                     Condition

       LED1                On            Fiber optic cable connection is
                                                      good

       LED1                Off           Fiber optic cable connection is
                                                     broken

       LED2                On            Card is inserted into the ring

       LED2                Off            Card is not inserted into the
                                                      ring

  Note:If the MAU type is set to 802.2J (JP2 - Pins 2 & 3 closed) LED1
  will not light until the adapter attempts insertion into the network.

