
OLICOM, INC.

OC-3230 TR/MODEM 144

Card Type                    Modem(asynchronous), Fax, NIC
Chip Set                     Texas Instruments TMS 380C25
Maximum Onboard Memory       32KB, 128KB for LAN buffers
Network Rate                 4/16Mbps
Maximum Data Rate            14.4Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     PCMCIA Type II
Fax Class                    Class I & II
Data Modulation Protocol     Bell 103A/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis
Fax Modulation Protocol      Unidentified
Error Correction/Compression MNP10, V.42bis
Topology                     Token Ring
Wiring Type                  Shielded/Unshielded twisted pair
Boot ROM                     128KB PROM

V1802/N1433

Proprietary AT Command Set

                    AUTO-RETRAIN - FALLBACK/FALLFORWARD

  Type:            Configuration

  Format:          AT [cmds] %E n [cmds]

  Description:     Controls auto-retrain mode and fallback/fall forward.

     Command                              Function

       %E0         Auto-retrain disabled

       %E1         Auto-retrain enabled

       %E2         Auto-retrain and Fallback/fall forward enabled

       %E3         Auto-retrain and Fallback/fall forward with fast hang
                   up enabled

                                BREAK SEND

  Type:          Configuration

  Format:        AT [cmds] \B n [cmds]

  Range:         1-9

  Unit:          .1 second

  Description:   Sends break of n to modem

                                BREAK TYPE

  Type:           Configuration

  Format:         AT [cmds] \K n
                  [cmds]

  Description:    Configures action of
                  break signal

     Command         Break from DTE      Modem receives      Break from
                                               \B          remote modem
                  Reliable/Normal mode

       \K0        Enter command mode,    Buffers           Buffers
                  do not send break to   cleared and       cleared and
                  remote modem.          break sent to     break sent to
                                         remote modem.     DTE.

       \K1        Buffers cleared and    Buffers           Buffers
                  break sent to remote   cleared and       cleared and
                  modem.                 break sent to     break sent to
                                         remote modem.     DTE.

       \K2        Enter command mode,    Send break to     Send break to
                  do not send break to   remote modem      DTE
                  remote modem.          immediately.      immediately.

       \K3        Send break to remote   Send break to     Send break to
                  modem immediately.     remote modem      DTE
                                         immediately.      immediately.

       \K4        Enter command mode,    Send break to     Break sent
                  do not send break to   remote modem      with received
                  remote modem.          with              data to the
                                         transmitted       DTE.
                                         data.

       \K5        Send break with        Send break to     Break sent
                  transmitted data.      remote modem      with received
                                         with              data to the
                                         transmitted       DTE.
                                         data.

                        CELLULAR TRANSMISSION LEVEL

  Type:            Configuration

  Format:          AT [cmds] @M n [cmds]

  Default:         Unidentified

  Range:           0 - 31

  Unit:            -1 dBm

  Description:     Sets the signal level for transmission when in leased
                   line mode

                            CHANGE COUNTRY CODE

  Type:          Configuration

  Format:        AT [cmds] *NC nn [cmds]

  Description:   Changes country code to one of 8 stored in NVRAM

                                COMPRESSION

  Type:          Configuration

  Format:        AT %C n

  Description:   Selects data compression.

    Command                              Function

      %C0        Data compression disabled

      %C1        MNP5 enabled

      %C2        V.42bis enabled

      %C3        MNP5 and V.42bis enabled

                           COMPROMISE EQUALIZER

  Type:          Configuration

  Format:        AT [cmds] :E n [cmds]

  Description:   Controls compromise equalizer

    Command                              Function

      :E0        Equalizer disabled

      :E1        Equalizer enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \N n [cmds]

  Description:   Sets connect mode

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        Reliable mode enabled

      \N3        Auto-reliable mode enabled

      \N4        LAPM mode only enabled

      \N5        MNP mode only enabled

                       DISPLAY CURRENT CONFIGURATION

  Type:          Immediate

  Format:        AT [cmds] \S [cmds]

  Description:   Displays current command profile

                          DISPLAY DELAYED NUMBERS

  Type:          Immediate

  Format:        AT [cmds] *B [cmds]

  Description:   Displays list of delayed numbers

                          DISPLAY DELAYED NUMBERS

  Type:          Immediate

  Format:        AT [cmds *D [cmds]

  Description:   Displays list of of delayed numbers

                         DISPLAY LINE SIGNAL LEVEL

  Type:          Immediate

  Format:        AT [cmds] %L [cmds]

  Description:   Displays received line signal level in dBm

                        DISPLAY LINE SIGNAL QUALITY

  Type:          Immediate

  Format:        AT [cmds] %Q [cmds]

  Description:   Displays line signal quality

                          DISPLAY STORED NUMBERS

  Type:          Immediate

  Format:        AT [cmds] \F [cmds]

  Description:   Displays all stored phone numbers

                                 FALL-BACK

  Type:          Configuration

  Format:        AT [cmds] -Q n [cmds]

  Description:   Enables fall back to V.22/V.22bis

    Command                              Function

      -Q0        V.22/V.22bis fall back enabled

      -Q1        V.22/V.22bis fall back disabled

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] \G n [cmds]

  Description:   Enables modem port flow control

    Command                              Function

      \G0        Flow control disabled

      \G1        Flow control enabled

                             LOCK SERIAL PORT

  Type:          Configuration

  Format:        AT [cmds] \J n [cmds]

  Description:   Sets operation of serial port speed

    Command                              Function

      \J0        Serial speed locked

      \J1        Serial speed follows connect speed

                             MAXIMUM MNP BLOCK

  Type:          Configuration

  Format:        AT [cmds] \A n [cmds]

  Description:   Sets the maximum transmission block size

    Command                              Function

      \A0        MNP block size is 64 characters

      \A1        MNP block size is 128 characters

      \A2        MNP block size is 192 characters

      \A3        MNP block size is 256 characters

                             MNP10 COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] -K n [cmds]

  Description:   Selects MNP10 data compression

    Command                              Function

      -K0        MNP10 disabled

      -K1        MNP10 enabled

                             MNP 10 HANDSHAKE

  Type:          Configuration

  Format:        AT [cmds] *H n [cmds]

  Description:   Selects MNP 10 link negotiation speed

    Command                              Function

      *H0        MNP 10 handshake at highest common speed

      *H1        MNP 10 handshake at 1200bps

      *H2        MNP 10 handshake at 4800bps

                         MNP10 POWER LEVEL ADJUST

  Type:                Configuration

  Format:              AT [cmds] )M n [cmds]

  Description:         Controls automatic transmit power level adjustment
                       during MNP 10 link negotiation

       Command                              Function

         )M0           Power level adjustment disabled

         )M1           Power level adjustment enabled

                           MNP STREAM/BLOCK MODE

  Type:          Configuration

  Format:        AT [cmds] \L n [cmds]

  Description:   Selects the transfer mode for MNP

    Command                              Function

      \L0        Stream mode for MNP enabled

      \L1        Block mode for MNP enabled

                              PROTOCOL/SPEED

  Type:          Configuration

  Format:        AT [cmds] F n [cmds]

  Description:   Selects protocol and line speed used

    Command                              Function

       F0        Select fastest common protocol

       F1        V.21/Bell 103A

       F3        Not used

       F3        V.23

       F4        V.22/Bell 212A 1200bps

       F5        V.22bis 2400bps

       F6        V.32bis/V.32 4800bps

       F7        V.32bis 7200bps

       F8        V.32bis/V.32 9600bps

       F9        V.32bis 12.0Kbps

      F10        V.32bis 14.4Kbps

                              PULSE DIAL CODE

  Type:          Configuration

  Format:        AT [cmds] *Z n [cmds]

  Description:   Selects digit used for pulse dial code

    Command                              Function

      *Z0        Use dial code 0

      *Z1        Use dial code 1

                       REMOTE CONFIGURATION PASSWORD

  Type:          Configuration

  Format:        AT [cmds] *C n [cmds]

  Description:   Store remote configuration password

                                REMOTE MNP

  Type:          Configuration

  Format:        AT [cmds] *R [cmds]

  Description:   Requests remote modems MNP configuration

                              SETUP PASSWORD

  Type:                  Configuration

  Format:                AT [cmds] *P xxxx / yyyy [cmds]

  Description:           Changes the modems password and callback
                         number. xxxx represents the password, and yyyy
                         represents the callback number.

                           V.23 SPLIT BAUD MODE

  Type:          Configuration

  Format:        AT [cmds] \W n [cmds]

  Description:   Controls V.23 split baud mode

    Command                              Function

      \W0        V.23 split baud mode disabled

      \W1        V.23 split baud mode enabled

                                 VIEW DATA

  Type:              Configuration

  Format:            AT [cmds] %F n [cmds]

  Description:       Selects split transmit and receive line speeds
                     during viewdata operation

      Command                              Function

        %F1          75bps transmit/1200bps receive when viewdata
                     selected

        %F2          1200bps transmit/75bps receive when viewdata
                     selected

                                S REGISTERS

           Register                      Function              Default

              S14                       Bit mapped           Unidentified

              S16                Bit mapped test options     Unidentified

              S20                       Bit mapped           Unidentified

              S21                       Bit mapped           Unidentified

              S22                   Bit mapped speaker       Unidentified
                                         options

              S23                       Bit mapped           Unidentified

              S24                 Sleep inactivity timer          0

              S27                       Bit mapped           Unidentified

              S28                       Bit mapped           Unidentified

              S29                  Flash modifier timer           0

              S31                       Bit mapped           Unidentified

              S33                     XOFF character             19

              S40                       Bit mapped           Unidentified

              S41                       Bit mapped           Unidentified

              S80                      Soft switch           Unidentified

              S99                  Leased line transmit      Unidentified
                                          level

             S201                Cellular transmit level     Unidentified

             S202                Remote escape character     Unidentified

