
SYSTRAN CORPORATION

SCRAMNET+ REHOSTABLE ADAPTER EVALUATION BOARD

NIC Type               Proprietary
Chipset                Systran Corporation
Maximum Onboard Memory 2MB DRAM (on daughterboard)
I/O Options            Bypass connector
Network Transfer Rate  150Mbps
Data Bus               VME double
Topology               Linear Bus/Ring
Wire Type              RG-58A/U 50ohm coaxial

                       Fiber optic cable
Boot ROM               Not available

[Image]

                                CONNECTIONS

          Function             Label           Function           Label

  Header to daughterboard       J1A      Testing pins               J7
  J1B

  Header to main board J1A      J1B      Media board header        J10

  Header to daughterboard       J2A      Bypass connector          J13
  J2B

  Header to main board J2A      J2B      RG-58A/U 50ohm            W1A
                                         coaxial receive
                                         connector 1

  Header to daughterboard       J3A      Fiber optic ST            W1B
  J3B                                    receive connector 1

  Header to main board J3A      J3B      Fiber optic SC            W1C
                                         receive connector 1

  Unidentified                  J4       RG-58A/U 50ohm            W2A
                                         coaxial receive
                                         connector 2

  Testing pins                  J6       Fiber optic ST            W2B
                                         receive connector 2

  Fiber optic SC receive        W2C      Fiber optic ST            W4B
  connector 2                            transmit connector 2

  RG-58A/U 50ohm coaxial        W3A      Fiber optic SC            W4C
  transmit connector 1                   transmit connector 2

  Fiber optic ST transmit       W3B      Header to main board      W5A
  connector 1                            J10

  Fiber optic SC transmit       W3C      Header to main board      W5B
  connector 1                            J10

  RG-58A/U 50ohm coaxial        W4A      Header to main board      W5C
  transmit connector 2                   J10

                        USER CONFIGURABLE SETTINGS

                 Setting                    Label          Position

     Media card power source is             H2A       Pins 1 & 2 closed
      internal

      Media card power source is             H2A       Pins 2 & 3 closed
      external

     Media card power source is             H2B       Pins 1 & 2 closed
      internal

      Media card power source is             H2B       Pins 2 & 3 closed
      external

      EEPROM write protect disabled          J4B       Pins 3 & 4 closed

      EEPROM write protect enabled           J4B       Pins 1 & 2 closed

     Address bits for internal CSR           J5            Closed
      enabled

      Address bits for internal CSR           J5             Open
      disabled

      EEPROM read protect disabled           J5B       Pins 3 & 4 closed

      EEPROM read protect enabled            J5B       Pins 1 & 2 closed

     Address bits for memory enabled         J8            Closed

      Address bits for memory disabled        J8             Open

     Address bits for external CSR           J9            Closed
      enabled

      Address bits for external CSR           J9             Open
      disabled

     TRIG1/TRIG2                            J11         Unidentified

      Chassis ground connected to signal     J12       Pins 3 & 4 closed
      ground

      Chassis ground not connected to        J12       Pins 1 & 2 closed
      signal ground

                            DRAM CONFIGURATION

  512KB, 1MB, or 2MB of memory may be factory installed on the
  daughterboard. The circuitry supports up to 8MB of memory. For other
  memory configurations, the user must provide an external memory
  interface.

                           CSR ADDRESS SELECTION

               Setting                                 S1

                00h, 20h                          Position 0

                 40h, 60h                          Position 4

                 80h, 80h                          Position 8

                 C0h, E0h                          Position C

                             DIAGNOSTIC LED(S)

     LED          Color         Status                Condition

    LED1          Green           On         Network connection is good

    LED1          Green          Off        Network connection is broken

    LED2          Green           On            Message is waiting in
                                                    transmit FIFO

    LED2          Green          Off          Message is not waiting in
                                                    transmit FIFO

    LED3          Green           On         Carrier signal is detected

    LED3          Green          Off            Carrier signal is not
                                                      detected

    LED4         Yellow           On          Error condition detected

    LED4         Yellow          Off        Error condition not detected

    LED5          Green           On          Message received from this
                                                        node

    LED5          Green          Off          Message not received from
                                                      this node

    LED6          Green           On        Message received from another
                                                        node

    LED6          Green          Off          Message not received from
                                                    another node

                       MISCELLANEOUS TECHNICAL NOTE

  The daughterboard is designed as a prototyping card for the user to
  design a VME bus network interface around. The main board shown above
  is only an evaluation board and is a separate product.

