
INTERPHASE CORPORATION

V/ATM 5215

NIC Type               ATM (OC-3c)
Processor              Motorola 68EC040
Processor Speed        20/25MHz
Maximum Onboard Memory 512KB SRAM/4MB SRAM
Cache                  1024KB SRAM
I/O Options            Serial port (exact location and function
                       unidentified)
Boot ROM               Not available
Network Transfer Rate  155Mbps
Topology               Unidentified
Wire Type              Fiber optic cable
Data Bus               VME double

[Image]

                                CONNECTIONS

         Function            Label            Function            Label

  Fiber optic transmit        CN1      Fiber optic receive         CN2
  cable connector                      cable connector

                        USER CONFIGURABLE SETTINGS

                   Setting                      Label        Position

     Power-on self-test enabled                 JA1           Open

      Power-on self-test disabled                JA1          Closed

     XON/XOFF flow control disabled             JA2           Open

      XON/XOFF flow control enabled              JA2          Closed

     Factory configured - do not alter          JA3           Open

     Factory configured - do not alter          JA4           Open

     Factory configured - do not alter          JA5           Open

     Serial port speed is 38.4K00bps            JA6           Open

      Serial port speed is 9600bps               JA6          Closed

     Processor speed is 25MHz                   JA7           Open

      Processor speed is 20MHz                   JA7          Closed

     Cache enabled                              JA8           Open

      Cache disabled                             JA8          Closed

     Factory configured - do not alter          JA9           Open

     Factory configured - do not alter          JA10          Open

     Serial port disabled                       JA11          Open

      Serial port enabled                        JA11         Closed

     GDB debug mode disabled                    JA12          Open

      GDB debug mode enabled                     JA12         Closed

     DTACK signal not filtered                  JA13         Closed

      DTACK signal filtered                      JA13          Open

     Card will request VME bus even when        JA14          Open
      its request level is unavailable

      Card will not request VME bus until        JA14         Closed
      its request level is available

     Card will use standard release mode        JA15          Open
      for releasing the VME bus

      Card will use early release mode for       JA15         Closed
      releasing the VME bus

     Short I/O size is 512 bytes                JA18         Closed

      Short I/O size is 2048 bytes               JA18          Open

     VRAM buffer not accessible to VME A24      JA19         Closed
      space

      VRAM buffer is accessible to VME A24       JA19          Open
      space

     VRAM allows non-privileged or              JA20         Closed
      privileged address modifiers

      VRAM allows privileged address             JA20          Open
      modifiers only

     Factory configured - do not alter          JA21          Open

     Factory configured - do not alter          JA22          Open

      Short I/O compare circuitry to accept      JA23          Open
      only privileged address modifiers

      Short I/O compare circuitry to accept      JA23         Closed
      both privileged and

      non-privileged address modifiers.

            Note:The manufacturer suggests that JA18 remain closed.

            Not all boards may support VRAM buffer access in VME A24
            space (jumper JA19). Contact the manufacturer for more
            information.

            If jumpers JA16 and JA17 are installed on your board they
            should remain open.

                   INTERRUPT REQUEST PRIORITY SELECTION

   Setting        BR0             BR1            BR2             BR3

      0        1 & 2, 3 &        4 & 5          4 & 5           4 & 5
                4, 5 & 6

      1          4 & 5         1 & 2, 3 &       4 & 5           4 & 5
                               4, 5 & 6

      2          4 & 5           4 & 5        1 & 2, 3 &        4 & 5
                                               4, 5 & 6

      3          4 & 5           4 & 5          4 & 5       1 & 2, 3 & 4,
                                                                5 & 6

            Note:Pins designated are in the closed position.

                     SHORT I/O BASE ADDRESS SELECTION

  Setting     JA24     JA25     JA26     JA27    JA28     JA29      JA30

      0000h  Closed   Closed   Closed   Closed   Closed   Closed   Closed

      0200h  Closed   Closed   Closed   Closed   Closed   Closed    Open

      0400h  Closed   Closed   Closed   Closed   Closed   Open     Closed

      0600h  Closed   Closed   Closed   Closed   Closed   Open      Open

      0800h  Closed    Open     Open    Closed   Closed   Closed   Closed

     6000h  Closed    Open     Open    Closed   Closed   Closed   Closed

      F600h   Open     Open     Open     Open    Closed   Open      Open

      F800h   Open     Open     Open     Open    Open     Closed   Closed

      FA00h   Open     Open     Open     Open    Open     Closed    Open

      FC00h   Open     Open     Open     Open    Open     Open     Closed

      FE00h   Open     Open     Open     Open    Open     Open      Open

            Note: A total of 128 base address settings are available. The
            jumpers are a binary representation of the decimal memory
            addresses. JA24 is the Most Significant Bit and jumper JA30
            is the Least Significant Bit. The jumpers have the following
            decimal values: JA24=32768, JA25=16384, JA26=8192, JA27=4096,
            JA28=2048, JA29=1024, JA30=512. Open the jumpers and add the
            values of the jumpers that are open to obtain the correct
            memory address. (Open=1, Closed=0)

                             DIAGNOSTIC LED(S)

   LED1      LED1        LED5       LED6        LED7        Condition
  Color     Status     Status      Status      Status

   Red        On      Blinking      Off         Off           Memory
                                                          diagnostic test
                                                              failed

   Red        On         Off      Blinking      Off       DMA diagnostic
                                                           test failed

   Red        On      Blinking    Blinking      Off        FE diagnostic
                                                           test failed

   Red        On         Off        Off          On       Firmware panic
                                                             condition
                                                             occurred

   Red        On         On         Off          On        VME bus error
                                                             occurred

   Red        On         Off         On          On       VME bus timeout
                                                             occurred

   Red        On      Blinking    Blinking    Blinking    Power-on reset
                                                           in progress

   Red        On         On          On          On       Power-on reset
                                                           in progress

  Green       On      Blinking    Blinking    Blinking      Common Boot
                                                         Interface ready

  Green       On        Cycle      Cycle       Cycle        Adapter is
                                                              active

   N/A       Off         N/A        N/A         N/A       Power is off or
                                                             board is
                                                            improperly
                                                            installed

                         DIAGNOSTIC LED(S) (CON'T)

     LED            Color           Status              Condition

    LED2        Unidentified          On         Board is accessing SRAM

    LED2        Unidentified         Off          Board is not accessing
                                                          SRAM

    LED3        Unidentified          On         Board is accessing VRAM

    LED3        Unidentified         Off          Board is not accessing
                                                          VRAM

    LED4        Unidentified          On        VME bus is performing DMA
                                                    transfer to board

    LED4        Unidentified         Off        VME bus is not performing
                                                  DMA transfer to board

   DBLED1           Green             On          Network connection is
                                                          good

   DBLED1           Green            Off          Network connection is
                                                         broken

   DBLED2          Yellow             On            Power-on reset in
                                                        progress

   DBLED2          Yellow          Blinking          Daughterboard is
                                                     initialized and
                                                       functioning

   DBLED2          Yellow            Off         Power-on reset complete

            Note:The term 'Cycle' in reference to LED5-LED7 indicated
            that the LEDs are turning on in sequence, one after the
            other.

            The colors of LED5-LED7 are unidentified.

            DBLED1 and DBLED2 are on the daughterboard.

