
CONNER PERIPHERALS, INC.

CTL96G-S

Device Type             Internal Tape Drive
Interface               SCSI
Format                  DDS-3
Sustained Transfer Rate 1,100KBPS

                        2,200KBPS (compressed)
Size                    5.25 in. full height
View                    Bottom


                                CONNECTIONS

                 Function                              Label

  Serial port (pin-out and function                     CN1
  unidentified)

                        USER CONFIGURABLE SETTINGS

                 Setting                       Label          Position

     MRS Mode disabled                        SW1/S4            On

      MRS Mode enabled                         SW1/S4           Off

     Parity check disabled                    SW1/S5           Off

      Parity check enabled                     SW1/S5            On

     Data compression enabled                 SW1/S6           Off

      Data compression disabled                SW1/S6            On

     Factory configured - do not alter        SW1/S7           Off

     Self-Test disabled                       SW1/S8           Off

      Self-Test enabled                        SW1/S8            On

  Note: MRS (Media Recognition System) Mode enabled allows drive to
  detect DDS cartridges that support this feature.

                              DRIVE SELECT ID

    Drive ID       JP1/Pins 1 & 2      JP1/Pins 3 & 4     JP1/Pins 5 & 6

         0             Open                Open               Open

          1            Closed               Open               Open

          2             Open               Closed              Open

          3            Closed              Closed              Open

          4             Open                Open              Closed

          5            Closed               Open              Closed

          6             Open               Closed             Closed

          7            Closed              Closed             Closed

  Note: If using Pins 1-6 of JP1 for SCSI ID selection, S1, S2, and S3 of
  SW1 must be set to the Off position.

                              DRIVE SELECT ID

     Drive ID            SW1/S1             SW1/S2            SW1/S3

          0              Off                Off                Off

           1               On                Off                Off

           2              Off                 On                Off

           3               On                 On                Off

           4              Off                Off                On

           5               On                Off                On

           6              Off                 On                On

           7               On                 On                On

  Note: If using S1, S2, and S3 of SW1 for SCSI ID selection, Pins 1-6 of
  JP1 must be set to the Open position.

                        TERMINATION POWER SELECTION

                  Setting                                JP2

     TERMPWR supplied by drive                        Closed

      TERMPWR supplied by SCSI interface                Open
      to drive

                      MANUFACTURERS RECOMMENDED MEDIA

         Tape               Capacity Without           Capacity With
                              Compression               Compression

  90 meter DDS-DC DAT       8.0GB (4 Tapes)          16.0GB (4 Tapes)
       cartridge

  120 meter DDS-2 DAT      16.0GB (4 Tapes)          32.0GB (4 Tapes)
       cartridge

  125 meter DDS-3 DAT      48.0GB (4 Tapes)          96.0GB (4 Tapes)
       cartridge

  Note: Above capacities are achieved by loading 4 cartridges only.


                             DIAGNOSTIC LED(S)

   LED        Color       Status                  Condition

   LED1       Green         On        Cartridge is inserted and does not
                                          generate excessive errors

   LED1       Green     Slow Flash    Cartridge is inserted but generates
                                       excessive errors (cleaning may be
                                                  required)

   LED1       Green     Fast Flash       Drive could not write to tape
                                        correctly - cleaning required

   LED1       Green        Off               Cartridge not loaded

   LED2       Amber         On        Drive is reading or writing to the
                                                     tape

   LED2       Amber     Fast Flash       A hardware fault occurred or
                                          moisture detected on tape

   LED2       Amber        Off        Drive is not reading or writing to
                                                   the tape

   LED3       Green         On        A data compression or decompression
                                        operation is in progress on the
                                              current cartridge

   LED3       Green        Off        A data compression or decompression
                                      operation is not in progress on the
                                              current cartridge

   LED4       Green         On          A write-protected cartridge is
                                               currently loaded

   LED4       Green        Off        A write-protected cartridge is not
                                               currently loaded

  Note: If LED1 flashes slowly during flash of LED2, a prerecorded audio
  cartridge is inserted and is being played automatically. Use DDS DAT
  cleaning cartridges only.

