
SIIG, INC.

SI-1414RI

Modem Type                   Data (synchronous/asynchronous)/Fax
Maximum Data Rate            14.4Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     Internal
Fax Class                    Class I & II
Data Modulation Protocol     ITU-T V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation Protocol      ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis

[Image]

  BASE I/O ADDRESS SELECTION

       Port             J1/A              J1/B              J1/C

  COM1: (3F8h)          Open              Open              Open

  COM2: (2F8h)         Closed             Open              Open

  COM3: (3E8h)          Open             Closed             Open

   COM4: (2E8h)       Closed            Closed             Open

  COM5: (2F0h)         Closed             Open             Closed

  COM6: (3E0h)          Open             Closed            Closed

  COM7: (2E0h)         Closed            Closed            Closed

                       INTERRUPT SELECTION

    IRQ       J1/D       J1/E       J1/F       J1/G       J1/H

     3        Open      Closed      Open       Open       Open

     4        Open       Open      Closed      Open       Open

     5        Open       Open       Open      Closed      Open

     7        Open       Open       Open       Open      Closed

     9       Closed      Open       Open       Open       Open

                         Proprietary AT Command Set

                           ACCEPT RELIABLE MODE

  Type:          Immediate

  Format:        AT [cmds] \U

  Example:       AT \U<CR>

  Description:   Accepts remote modems request for reliable link.

                     AUTO-RELIABLE FALLBACK CHARACTER

  Type:              Configuration

  Format:            AT [cmds] %An [cmds]

  Example:           AT%A20<CR>

  Default:           19

  Range:             0-127

  Unit:              ASCII

  Description:       Sets the character used as the auto-reliable
                     fallback character. %A0 will disable this function.

                                BREAK SEND

  Type:          Configuration

  Format:        AT [cmds] \Bn [cmds]

  Example:       AT \B3 &W<CR>

  Range:         1-9

  Unit:          .1 second

  Description:   Sends break to modem.

                                BREAK TYPE

  Type:          Configuration

  Format:        AT [cmds] \Kn [cmds]

  Example:       AT \K1 <CR>

  Description:   Configures action of break signal.

  Command                                Function

  \K0            Online command mode enabled, send no break to remote
                 modem.

  \K1            Break sent to remote modem and buffered cleared.

  \K2            Online command mode enabled, send no break to remote
                 modem.

  \K3            Send break to remote modem immediately.

  \K4            Online command mode enabled, send no break to remote
                 modem.

  \K5            Send break with transmitted data.

                            COMMUNICATIONS MODE

  Type:           Configuration

  Format:         AT [cmds] &Mn [cmds]

  Example:        AT &M0 &E1<CR>

  Description:    Selects communications mode.

  Command                                Function

  &M0             Asynchronous mode.

  &M1             Synchronous connect mode and asynchronous off-line
                  command mode.

  &M2             Synchronous connect mode and asynchronous off-line
                  command mode and set DTR high.

  &M3             Synchronous connect mode.

   &M5           V.42 connection enabled.

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] %Cn [cmds]

  Example:       AT *EC0 %C1 *AP0<CR>

  Description:   Selects data compression.

    Command                              Function

  %C0            Data compression disabled.

   %C1          Data compression enabled.

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Example:       AT \N1 DT555-1212<CR>

  Description:   Sets connect mode.

    Command                              Function

      \N0        Normal mode.

      \N1        Direct mode.

      \N2        Reliable mode.

      \N3        Auto-reliable mode.

      \N4        V.42bis reliable mode with phase detection.

      \N5        V.42bis auto-reliable mode with phase detection.

      \N6        V.42 reliable mode without phase detection.

      \N7        V.42 auto-reliable mode without phase detection.

                         CONVERT TO RELIABLE MODE

  Type:          Immediate

  Format:        AT [cmds] \O [cmds]

  Example:       AT \O<CR>

  Description:   Initiates reliable mode link.

                                 ECHO DATA

  Type:          Configuration

  Format:        AT [cmds] \En [cmds]

  Example:       AT \E0<CR>

  Description:   Enables modem to echo received data.

  Command                                Function

   \E0          Data echo disabled.

  \E1            Data echo enabled.

                             FLOW CONTROL TYPE

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Example:       AT *MF1 *DF1 &K5<CR>

  Description:   Sets type of flow control used by modem.

  Command                                Function

  &K0            Flow control disabled.

  &K3            CTS/RTS flow control enabled.

   &K4          XON/XOFF flow control enabled.

  &K5            XON/XOFF pass-through flow control enabled.

                             FLOW CONTROL TYPE

  Type:          Configuration

  Format:        AT [cmds] \Qn [cmds]

  Example:       AT \Q0 A<CR>

  Description:   Sets type of flow control used by modem.

  Command                                Function

  \Q0            Flow control disabled.

  \Q1            XON/XOFF flow control enabled.

  \Q2            CTS flow control enabled.

   \Q3          CTS/RTS flow control enabled.

                             LOCK SERIAL PORT

  Type:          Configuration

  Format:        AT [cmds] \Jn [cmds]

  Example:       AT %L3 %B14 \J0<CR>

  Description:   Sets operation of serial port speed.

  Command                                Function

   \J0          Serial speed locked.

  \J1            Serial speed follows connect speed.

                    MAXIMUM BLOCK SIZE FOR TRANSMISSION

  Type:          Configuration

  Format:        AT [cmds] \An [cmds]

  Example:       AT \A3 %C1<CR>

  Description:   Sets the maximum transmittable block size.

  Command                                Function

  \A0            Maximum MNP block size is 64 characters.

  \A1            Maximum MNP block size is 128 characters.

  \A2            Maximum MNP block size is 192 characters.

   \A3          Maximum MNP block size is 256 characters.

                         MNP EXTENDED RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] \Vn [cmds]

  Example:       AT \V1 %C1<CR>

  Description:   Selects MNP extended result codes.

  Command                                Function

  \V0            MNP extended result codes disabled.

   \V1          MNP extended result codes enabled.

                        V.42 EXTENDED RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] \Wn [cmds]

  Example:       AT \W1 %C1<CR>

  Description:   Selects V.42 extended result codes.

  Command                                Function

  \W0            V.42 extended result codes disabled.

   \W1          V.42 extended result codes enabled.

                           XON/XOFF PASS-THROUGH

  Type:          Configuration

  Format:        AT [cmds] \Xn [cmds]

  Example:       AT \X0 <CR>

  Description:   Selects whether XON/XOFF signals are sent to remote
                 modem.

  Command                                Function

  \X0            XON/XOFF signals trapped by local modem.

  \X1            XON/XOFF passed through local modem.

