
PUREDATA, LTD.

SATISFAXTION MODEM/300

Modem Type                   Data (asynchronous)/Fax
Maximum Data Rate            14.4Kbps
Maximum Fax Rate             9600bps
Data Bus                     8-bit ISA
Fax Class                    Class I
Data Modulation Protocol     Bell 103A/212A

                             ITU-T V.22, V.22bis, V.32, V.32bis
Fax Modulation Protocol      ITU-T V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis

[Image]

                                CONNECTIONS

         Purpose           Location            Purpose           Location

  Line out                    CN1       Line in                    CN2

             BASE I/O ADDRESS SELECTION

       Port             SW1/A            SW1/B

  COM1: (3F8h)           On                On

   COM2: (2F8h)         Off               On

  COM3: (3E8h)           On               Off

  COM4: (2E8h)           Off              Off

            INTERRUPT SELECTION

   IRQ    SW1/C    SW1/D    SW1/E    SW1/F

  2         On      Off      Off      Off

   3      Off       On      Off      Off

  4        Off      Off      On       Off

  5        Off      Off      Off      On

                         Proprietary AT Command Set

                           ACCEPT RELIABLE MODE

  Type:          Immediate

  Format:        AT [cmds] \Un

  Example:       AT \U<CR>

  Description:   Accepts remote modems request for reliable link.

                    AUTO-RETRAIN - FALLBACK/FALLFORWARD

  Type:          Configuration

  Format:        AT [cmds] %En [cmds]

  Example:       AT %E1 <CR>

  Description:   Controls auto-retrain mode and fallback/fall forward.

  Command                                Function

  %E0            Auto-retrain disabled.

   %E1          Auto-retrain enabled.

  %E2            Fallback/fall forward enabled.

                          BIT-MAPPED REGISTER S14

  Format                   AT [cmds] S14? [cmds]

  Example:                 ATS14?<CR>

  Default:                 Read only

  Range:                   0-255

  Unit:                    Bit-mapped.

  Description:             Displays echo, result codes, result code
                           display, dial mode, and answer/originate mode.

       Bit         Value                       Function

        0          1          Not used.

        1          0          Command echo disabled.

                    1        Command echo enabled.

        2           0        Result codes enabled.

                   1          Result codes disabled.

        3          0          Display result codes in numeric format.

                    1        Display result codes in verbose format.

        4          0          Not used.

        5           0        Tone dial enabled.

                   1          Pulse dial enabled.

        6          0          Not used.

        7          0          Answer mode enabled.

                    1        Originate mode enabled.

                          BIT-MAPPED REGISTER S21

  Format                    AT [cmds] S21? [cmds]

  Example:                  ATS21?<CR>

  Default:                  Read only

  Range:                    0 - 255

  Unit:                     Bit-mapped

  Description:              Displays low DTR action, DCD signal, DSR
                            signal, and the Long Space Disconnect
                            function.

       Bit         Value                        Function

      2 - 0           010      Not used.

      4, 3         00          DTR signal ignored.

                   01          Modem goes to command mode on low DTR.

                    10        Modem disconnects on low DTR. Auto-Answer
                               is disabled.
                   11
                               Modem is initialized on low DTR.

        5          0           DCD forced high.

                    1         DCD normal.

        6           0         DSR forced high.

                   1           DSR normal.

        7           0         Long Space Disconnect function disabled.

                   1           Long Space Disconnect function enabled.

                          BIT-MAPPED REGISTER S22

  Format                    AT [cmds] S22? [cmds]

  Example:                  AT S22?<CR>

  Default:                  Read only

  Range:                    0 - 255

  Unit:                     Bit-mapped.

  Description:              Displays volume and speaker settings, result
                            codes, and make/break pulse ratio.

       Bit          Value                       Function

       1, 0         00          Lowest volume setting.

                    01          Low volume setting.

                     10        Medium volume setting

                    11          Highest volume setting.

       3, 2         00          Speaker disabled.

                     01        Speaker enabled until carrier signal
                                detected
                    10
                                Speaker enabled.
                    11
                                Speaker enabled following dialing, then
                                disabled after carrier signal detected.

     6, 5 ,4        000         Busy and dialtone detection disabled,
                                result codes 0-4 enabled.
                    100
                                Busy and dialtone detection disabled,
                    101         result codes 0-5, 10 enabled.

                    110         Busy tone detection disabled, dialtone
                                detection enabled, result codes 0-6, 10
                     111       enabled.

                                Busy tone detection enabled, dialtone
                                detection disabled, result codes 0-5, 7,
                                10 enabled.

                                Busy and dialtone detection enabled,
                                result codes 0-7, 10 enabled.

        7            0         39/61ms at 10pps (North America)

                    1           33/67ms at 10pps (Europe)

                          BIT-MAPPED REGISTER S23

  Format                AT [cmds] S23? [cmds]

  Example:              ATS23?<CR>

  Default:              Read only

  Range:                0-255

  Unit:                 Bit-mapped

  Description:          Displays DTE rate and parity.

     Bit       Value                          Function

      0        1            Not used.

   3, 2, 1         000      Sets serial port speed to 0-300bps.

                   001      Sets serial port speed to 600bps.

                   010      Sets serial port speed to 1200bps.

                   011      Sets serial port speed to 2400bps.

                   100      Sets serial port speed to 4800bps.

                   101      Sets serial port speed to 9600bps.

                   110      Sets serial port speed to 19200bps.

                  111       Sets serial port speed to 38400bps.

     5,4        00         Parity even.

               10           Parity odd.

     7, 6      0            Not used.

                          BIT-MAPPED REGISTER S27

  Format                AT [cmds] S27? [cmds]

  Example:              ATS27?<CR>

  Default:              Read only

  Range:                0 - 255

  Unit:                 Bit-mapped

  Description:          Displays protocol type.

     Bit        Value                         Function

    1 - 0       0          Not used.

    5 - 3       0          Not used.

      6         0          Select CCITT protocols.

                 1        Select Bell protocols.

     7, 2       0          Not used.

                                BREAK SEND

  Type:          Configuration

  Format:        AT [cmds] \Bn [cmds]

  Example:       AT \B3 &W<CR>

  Default:       3

  Range:         1-9

  Unit:          .1 second

  Description:   Sends break to modem.

                                BREAK TYPE

  Type:           Configuration

  Format:         AT [cmds] \Kn [cmds]

  Example:        AT \K1 <CR>

  Description:    Configures action of break signal.

     Command       Break from DTE        Break from       Modem receives
                                       remote modem             \B

  \K0              Enter command      Buffers cleared    Send break to
                   mode, do not       and break sent     remote modem
                   send break to      to DTE.            immediately,
                   remote modem.                         then enter
                                                         command mode.

  \K1              Buffers cleared    Buffers cleared    Send break to
                   and break sent     and break sent     remote modem
                   to remote modem.   to DTE.            immediately.

  \K2              Enter command      Send break to      Send break to
                   mode, do not       DTE immediately.   remote modem
                   send break to                         immediately,
                   remote modem.                         then enter
                                                         command mode.

  \K3              Send break to      Send break to      Send break to
                   remote modem       DTE immediately.   remote modem
                   immediately.                          immediately.

  \K4              Enter command      Break sent with    Send break to
                   mode, do not       received data to   remote modem
                   send break to      the DTE.           immediately,
                   remote modem.                         then enter
                                                         command mode.

   \K5            Send break with    Break sent with    Send break to
                   transmitted        received data to   remote modem
                   data.              the DTE.           immediately.

                                COMPRESSION

  Type:          Configuration

  Format:        AT %Cn

  Example:       AT *EC0 %C1 *AP0<CR>

  Description:   Selects data compression.

    Command                              Function

  %C0            Data compression disabled.

   %C1          Data compression enabled.

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Example:       AT \N1 DT555-1212<CR>

  Description:   Sets connect mode.

    Command                              Function

  \N0            Normal mode enabled.

  \N1            Diagnostic mode, select this before selecting &T
                 commands.

  \N2            Reliable mode enabled.

   \N3          Auto-reliable mode enabled.

  \N4            LAPM mode enabled.

                         CONVERT TO RELIABLE MODE

  Type:          Immediate

  Format:        AT [cmds] \Y [cmds]

  Example:       AT \Y<CR>

  Description:   Initiates reliable mode link.

                           EXTENDED RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] \Vn [cmds]

  Example:       AT \V1 %C1<CR>

  Description:   Selects extended result codes.

  Command                                Function

  \V0            Extended result codes disabled.

  \V1            Reliable result codes enabled.

   \V2          Error correction and compression result codes enabled.

  \V3            DTE speed result codes enabled.

                             FLOW CONTROL TYPE

  Type:          Configuration

  Format:        AT [cmds] \Qn [cmds]

  Example:       AT \Q3 A <CR>

  Description:   Sets type of flow control used by modem.

  Command                                Function

  \Q0            Flow control disabled.

  \Q1            XON/XOFF flow control enabled.

   \Q3          RTS/CTS flow control enabled.

                             INACTIVITY TIMER

  Type:             Configuration

  Format:           AT [cmds] \Tn [cmds]

  Example:          AT\T5<CR>

  Default:          0

  Range:            0-42

  Unit:             1 minute

  Description:      Sets the length of time that the modem does not
                    receive information before it disconnects.

                    MAXIMUM BLOCK SIZE FOR TRANSMISSION

  Type:          Configuration

  Format:        AT [cmds] \An [cmds]

  Example:       AT \A3 &MB28800<CR>

  Description:   Sets the maximum transmittable block size.

    Command                              Function

  \A0            Maximum MNP block size is 64 characters.

  \A1            Maximum MNP block size is 128 characters.

   \A2          Maximum MNP block size is 192 characters.

  \A3            Maximum MNP block size is 256 characters.

                         ON-LINE IN RELIABLE MODE

  Type:          Immediate

  Format:        AT [cmds] \O

  Example:       AT \O <CR>

  Description:   Returns to on-line and requests reliable mode
                 connection.

                              PROTOCOL/SPEED

  Type:          Register

  Format:        AT [cmds] S31=n [cmds]

  Example:       AT S31=0 <CR>

  Description:   Selects the maximum DCE speed.

    Command                              Function

   S31=0        Select last speed at AT command.

  S31=3          Select 300bps speed.

  S31=5          Select 1200bps speed.

  S31=6          Select 2400bps speed.

  S31=7          Select 4800bps speed.

  S31=8          Select 7200bps speed.

  S31=9          Select 9600bps speed.

  S31=10         Select 12Kbps speed.

  S31=11         Select 14.4Kbps speed.

                          RETURN TO RELIABLE MODE

  Type:          Immediate

  Format:        AT [cmds] \Z [cmds]

  Example:       AT \Z <CR>

  Description:   Ends reliable mode link, initiate return to normal mode.

                                TEST MODES

  Format                  AT [cmds] S16=n [cmds]

  Example:                ATS16=40<CR>

  Default:                0

  Range:                  0-125

  Unit:                   Bit-mapped

  Description:            Controls loopback tests, analog, digital,
                          remote digital, and self tests.

      Bit          Value                       Function

       0          0         Local analog loopback not in progress.

                 1           Local analog loopback in progress.

       1          0         Not used.

     5 - 1       0           Not used.

       6          0         Local analog loopback w/ self-test not in
                             progress.
                 1
                             Local analog loopback w/ self-test in
                             progress.

                        V.42bis COMPRESSION CONTROL

  Type:          Configuration

  Format:        AT [cmds] "Hn [cmds]

  Example:       AT "H3 &W<CR>

  Description:   Controls V.42bis data compression

  Command                                Function

  "H0            V.42bis disabled.

  "H1            V.42bis when transmitting enabled.

  "H2            V.42bis when receiving enabled.

   "H3          V.42bis when transmitting/receiving enabled.

                           XON/XOFF PASS-THROUGH

  Type:          Configuration

  Format:        AT [cmds] \Xn [cmds]

  Example:       AT \X1 O<CR>

  Description:   Selects whether XON/XOFF signals are sent to remote
                 modem.

  Command                                Function

   \X0          XON/XOFF signals trapped by local modem.

  \X1            XON/XOFF passed through local modem.

