
PURE DATA, LTD.

SATISFAXTION MODEM/200

Card Type                    Modem(asynchronous)
Chip Set                     Intel
Maximum Data Rate            2400bps
Maximum Fax Rate             9600bps
Data Bus                     16 bit ISA
Fax Class                    Class I & II
Data Modulation Protocol     Bell 103A/212A

                             ITU-T V.21, V.22, V.22bis
Fax Modulation Protocol      Unidentified
Error Correction/Compression MNP5, V.42, V.42bis

[Image]

                                CONNECTIONS

        Function           Label             Function              Label

  Line in                      CN1      Unidentified                CN3

  Line out                     CN2

                         Proprietary AT Command Set

                        ACCEPT RELIABLE CONNECTION

  Type:          Configuration

  Format:        AT [cmds] \U [cmds]

  Description:        Accepts remote modems request for MNP reliable
                      link.

                     AUTO-RELIABLE FALLBACK CHARACTER

  Type:            Configuration

  Format:          AT [cmds] %An [cmds]

  Default:         19

  Range:           0-127

  Unit:            ASCII

  Description:     Sets the character used as the auto-reliable fallback
                   character

                  AUTO-RELIABLE TIME BUFFER CONFIGURATION

  Type:                  Configuration

  Format:                AT [cmds] \Cn [cmds]

  Description:           Controls the handling of incoming data during
                         auto-reliable time period

        Command                              Function

          \CO            Disabled

          \C1            Enable 200 character buffer. If 200 characters
                         received without reliable character, establish
                         normal connection

          \C2            Auto reliable buffer disabled. Establish normal
                         connection on receipt of escape character

                          BIT-MAPPED REGISTER S14

  Format               AT [cmds] S14=n [cmds]

  Default:             138

  Range:               0-174

  Unit:                Bit-mapped

  Description:         Controls echo, result codes, result code display,
                       dial mode, and answer/originate mode

   Bit       Value                          Function

    0              0   Not used

    1               0  Command echo disabled

                   1   Command echo enabled

    2               0  Result codes enabled

                   1   Result codes disabled

    3               0  Display result codes in numeric format

                   1   Display result codes in verbose format

    4              0   Not used

    5               0  Tone dial enabled

                   1   Pulse dial enabled

    6              0   Not used

    7               0  Answer mode enabled

                   1   Originate mode enabled

                          BIT-MAPPED REGISTER S21

  Format                 AT [cmds] S21=n [cmds]

  Default:               48

  Range:                 0 - 254

  Unit:                  Bit-mapped

  Description:           Controls S23, CTS action, DTR action, DCD
                         action, DSR action and the Long Space Disconnect
                         function.

    Bit       Value                          Function

     0               0   Not used

     1                0  Option 1 for bits 1, 2 and 3 of S32 enabled

                     1   Option 2 for bits 1, 2 and 3 of S23 enabled

     2                0  CTS signal normal

                     1   CTS signal forced high

   4, 3              00  DTR signal ignored

                     01  Modem goes to command mode on low DTR

                     10  Modem disconnects on low DTR. Auto-Answer is
                         disabled
                    11
                         Modem is initialized on low DTR

     5                0  DCD signal forced high

                     1   DCD signal normal

     6                0  DSR signal forced high

                     1   DSR signal normal

     7                0  Long Space Disconnect function disabled

                     1   Long Space Disconnect function enabled

                          BIT-MAPPED REGISTER S22

  Format                AT [cmds] S22=n [cmds]

  Default:              118

  Range:                0-255

  Unit:                 Bit-mapped

  Description:          Controls speaker, result codes and make/break
                        ratio

    Bit       Value                         Function

   1, 0            00   Off volume

                   01   On volume

                   10   Medium level volume

                  11    High level volume

   3, 2            00   Speaker off

                   01   Speaker off on carrier

                   10   Speaker always on

                  11    Speaker on during handshake

  6, 5, 4         000   Blind dial and basic result codes only enabled

                  100   Blind dial and basic and connection speed result
                        codes enabled
                  101
                        Blind dial and basic and connection speed result
                  110   codes and dialtone detection enabled

                 111    Blind dial, basic and connection speed result
                        codes and dialtone detection enabled

                        Blind dial, basic and connection speed result
                        codes, busy and dialtone detection enabled

     7              0   Make/Break pulse ratio at 39/61

                   1    Make/Break pulse ration at 33/67

                          BIT-MAPPED REGISTER S23

  Format                AT [cmds] S23=n [cmds]

  Default:              Unidentified

  Range:                0-191

  Unit:                 Bit-mapped

  Description:          Grants/denies remote digital loopback, controls
                        DTE rate and parity, and sets guard tone

            Note: See S21 bit one to set option 1 and 2

    Bit       Value                         Function

     0              0   Remote digital loopback ignored

                   1    Remote digital loopback accepted

                        Option 1 (bit 1 of S21 = 0)

  3, 2, 1         000   Sets serial port speed to 0-300bps

                  001   Sets serial port speed to 1200bps

                  010   Sets serial port speed to 2400bps

                  011   Sets serial port speed to 4800bps

                  101   Sets serial port speed to 9600bps

                  110   Sets serial port speed to 19.2Kbps

                 111    Sets serial port speed to 38.4Kbps

                        Option 2 (bit 1 of S21 = 1)

  3, 2, 1         000   Sets serial port speed to 12.0Kbps

                  001   Sets serial port speed to 14.4Kbps

                 010    Sets serial port speed to 57.6Kbps

    5,4            00   Parity even

                   01   Parity space/no parity

                   10   Parity odd

                  11    Parity mark

   7, 6            00   Guard tone disabled

                   01   550Hz guard tone enabled

                  10    1800Hz guard tone enabled

                          BIT-MAPPED REGISTER S27

  Format           AT [cmds] S27=n [cmds]

  Default:         73

  Range:           0 - 255

  Unit:            Bit-mapped

  Description:     Controls communications mode, line type, and protocol
                   type

   Bit    Value                           Function

    0         0    Not used

    1         0    Not used

  7, 2        00   Switched line

              01   Leased line

              10   Not used

             11    Leased line

    3         0    Not used

    4         0    Not used

    5         0    Not used

    6          0   Select CCITT protocols

              1    Select Bell protocols

                               BREAK SEND

  Type          Configuration

  Format        AT [cmds] \Bn [cmds]

  Default       3

  Range         1 -9

  Unit          .1 second

  Description   Sends break of n

                                BREAK TYPE

  Type:                    Configuration

  Format:                  AT [cmds] \Kn [cmds]

  Description:             Configures action of break signal

    Command       Break from DTE      Break from DTE    Break from remote
                                     while in command         modem
                                          mode

      \K0         Enter command     Buffers cleared     Buffers cleared
                  mode, do not      and break sent to   and break sent to
                  send break to     remote modem        remote modem
                  remote modem

      \K1         Buffers cleared   Buffers cleared     Buffers cleared
                  and break sent    and break sent to   and break sent to
                  to remote modem   remote modem        remote modem

      \K2         Enter command     Send break to       Send break to
                  mode, do not      remote modem        remote modem
                  send break to     immediately         immediately
                  remote modem

      \K3         Send break to     Send break to       Send break to
                  remote modem      remote modem        remote modem
                  immediately       immediately         immediately

      \K4         Enter command     Send break to       Send break to
                  mode, do not      remote modem with   remote modem with
                  send break to     transmitted data    transmitted data
                  remote modem

      \K5         Send break with   Send break to       Send break to
                  transmitted       remote modem with   remote modem with
                  data              transmitted data    transmitted data

                                COMPRESSION

  Type:          Configuration

  Format:        AT %Cn

  Description:   Selects MNP5 data compression

    Command                              Function

      %C0        Data compression disabled

      %C1        Data compression enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Sets connect mode

    Command                              Function

      \N0        Normal mode enabled

      \N2        MNP mode enabled

      \N3        LAPM mode enabled

      \N4        LAPM mode enabled

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] \Gn [cmds]

  Description:   Selects modem port flow control

    Command                              Function

      \G0        Flow control disabled

      \G1        Flow control enabled

                             FLOW CONTROL TYPE

  Type:                Configuration

  Format:              AT [cmds] \Qn [cmds]

  Description:         Sets type of flow control used by modem

       Command                              Function

         \Q0           Flow control disabled

         \Q1           Bidirectional XON/XOFF flow control enabled

         \Q2           CTS flow control by DCE enabled

         \Q3           Bidirectional CTS/RTS flow control enabled

         \Q4           XON/XOFF flow control by DCE enabled

         \Q5           CTS flow control by DCE enabled. CTS low until
                       connection established

         \Q6           Bidirectional CTS/RTS flow control enabled. CTS
                       low until connection established

                             INACTIVITY TIMER

  Type:                  Configuration

  Format:                AT [cmds] \Tn [cmds]

  Default:               0

  Range:                 0-90

  Unit:                  1 minute

  Description:           Sets the length of time that the modem does not
                         receive information before it disconnects

                             LOCK SERIAL PORT

  Type:          Configuration

  Format:        AT [cmds] \Jn [cmds]

  Description:   Sets operation of serial port speed

    Command                              Function

      \J0        Serial speed locked

      \J1        Serial speed follows connect speed

                              LOOPBACK TESTS

  Format            AT [cmds] S16=n [cmds]

  Default:          0

  Range:            0 - 125

  Unit:             Bit-mapped

  Description:      Enables loopback tests

   Bit     Value                          Function

    0            0  Local analog loopback test disabled

                1   Local analog loopback test enabled

    1           0   Not used

    2            0  Local digital loopback test disabled

                1   Local digital loopback test enabled

    3            0  Modem is not performing remotely requested remote
                    digital loopback test
                1
                    Modem is performing remotely requested remote digital
                    loopback test

    4            0  Modem is not performing locally requested remote
                    digital loopback test
                1
                    Modem is performing locally requested remote digital
                    loopback test

    5            0  Remote digital loopback with local self-test disabled

                1   Remote digital loopback with local self-test enabled

    6            0  Local analog loopback with local self-test disabled

                1   Local analog loopback with local self-test enabled

                    MAXIMUM BLOCK SIZE FOR TRANSMISSION

  Type:          Configuration

  Format:        AT [cmds] \An [cmds]

  Description:   Sets the maximum transmittable block size

    Command                              Function

      \A0        MNP block size is 64 characters

      \A1        MNP block size is 128 characters

      \A2        MNP block size is 192 characters

      \A3        MNP block size is 256 characters

                           MNP STREAM/BLOCK MODE

  Type:          Configuration

  Format:        AT [cmds] \Ln [cmds]

  Description:   Selects the transfer mode for MNP

    Command                              Function

      \L0        Stream mode for MNP enabled

      \L1        Block mode for MNP enabled

                            RESULT CODE FORMAT

  Type:          Configuration

  Format:        AT [cmds] \Vn [cmds]

  Description:   Selects format for information-text and result codes

    Command                              Function

       V0        Numeric format enabled

       V1        Verbose (word) format enabled

                           SWITCH TO NORMAL MODE

  Type:          Configuration

  Format:        AT [cmds] \Z [cmds]

  Description:   Switches to normal mode from MNP mode

                             TEST TIME LIMIT

  Type          Configuration

  Format        AT [cmds] S18=n [cmds]

  Default       0

  Range         0 - 255

  Unit          1 second

  Description   Limits time allowed for diagnostic test

                           V.42 DETECTION PHASE

  Type:          Configuration

  Format:        AT [cmds] -Jn [cmds]

  Description:   Controls V.42 detection

    Command                              Function

      -J0        V.42 detection disabled

      -J1        V.42 detection enabled

                        V.42bis COMPRESSION CONTROL

  Type:          Configuration

  Format:        AT [cmds] "Hn [cmds]

  Description:   Controls V.42bis data compression

    Command                              Function

      "H0        V.42bis disabled

      "H1        V.42bis when transmitting enabled

      "H2        V.42bis when receiving enabled

      "H3        V.42bis when transmitting/receiving enabled

                       V.42bis MAXIMUM STRING LENGTH

  Type:          Configuration

  Format:        AT [cmds] "O=n [cmds]

  Default:       250

  Range:         6 -250

  Unit:          Unidentified

  Description:   Selects string size for V.42bis compression

                           XON/XOFF PASS-THROUGH

  Type:          Configuration

  Format:        AT [cmds] \Xn [cmds]

  Description:   Selects whether XON/XOFF signals are sent to remote
                 modem

    Command                              Function

      \X0        XON/XOFF signals trapped by local modem

      \X1        XON/XOFF passed through local modem

