
MAXATECH

PCM144C

Card Type                    Fax, Modem (asynchronous)
Chip Set                     Unidentified
Maximum Data Rate            14.4Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     PCMCIA Type II
Fax Class                    Class I
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.21, V.22, V.22bis, V.32, V.32bis
Fax Modulation Protocol      ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis

                                                                      V1857

                         Proprietary AT Command Set

                         ACCEPT MNP RELIABLE MODE

  Type:          Immediate

  Format:        AT [cmds] \U [cmds]

  Description:   Accept remote modems request for MNP reliable mode

                        AUTO-FALLBACK/FALL-FORWARD

  Type:          Configuration

  Format:        AT [cmds] %Gn [cmds]

  Description:   Selects auto-fallback/fall-forward

    Command                              Function

      %G0        Auto-fallback/fall-forward disabled

      %G1        Auto-fallback/fall-forward enabled

                     AUTO-RELIABLE FALLBACK CHARACTER

  Type:                  Configuration

  Format:                AT [cmds] %An [cmds]

  Default:               Unidentified

  Range:                 0-127

  Unit:                  ASCII

  Description:           Sets the character used as the auto-reliable
                         fallback character; %A0 will disable this
                         function.

                  AUTO-RELIABLE TIME BUFFER CONFIGURATION

  Type:                  Configuration

  Format:                AT [cmds] \Cn [cmds]

  Description:           Controls the handling of incoming data during
                         auto-reliable time period

        Command                              Function

          \C0            Data is discarded

          \C1            Data is buffered

          \C2            Data is discarded; modem returns to normal mode
                         on receiving auto-reliable fallback character.

                               AUTO-RETRAIN

  Type:          Configuration

  Format:        AT [cmds] %En [cmds]

  Description:   Controls auto-retrain mode

    Command                              Function

      %E0        Auto-retrain disabled

      %E1        Auto-retrain enabled

      BIT MAPPED REGISTERS

    Register        Default

      S14        Unidentified

      S21        Unidentified

      S22        Unidentified

      S23        Unidentified

      S27        Unidentified

                                BREAK SEND

  Type:          Configuration

  Format:        AT [cmds] \Bn [cmds]

  Default:       3

  Range:         1-9

  Unit:          .1 second

  Description:   Sends break to modem

                                BREAK TYPE

  Type:          Configuration

  Format:        AT [cmds] \Kn [cmds]

  Default:       5

  Range:         0-5

  Description:   Configures action of break signal

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] %Cn [cmds]

  Description:   Selects data compression

    Command                              Function

      %C0        Data compression disabled

      %C1        MNP5 enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        MNP reliable mode enabled

      \N3        Auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

                       CONVERT TO MNP RELIABLE MODE

  Type:          Immediate

  Format:        AT [cmds] \Y [cmds]

  Description:   Converts to MNP reliable mode from normal or direct mode

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] \Gn [cmds]

  Description:   Selects modem port flow control

    Command                              Function

      \G0        Flow control disabled

      \G1        Flow control enabled

                             FLOW CONTROL TYPE

  Type:          Configuration

  Format:        AT [cmds] \Qn [cmds]

  Description:   Sets type of flow control used by modem

    Command                              Function

      \Q0        Flow control disabled

      \Q1        Bidirectional XON/XOFF flow control enabled

      \Q2        CTS flow control by DCE enabled

      \Q3        Bidirectional RTS/CTS flow control enabled

                           EXTENDED RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] \Vn [cmds]

  Description:   Selects extended result codes

    Command                              Function

      \V0        Extended result codes disabled

      \V1        Extended result codes set 1 enabled

      \V2        Extended result codes set 2 enabled

                             INACTIVITY TIMER

  Type:                  Configuration

  Format:                AT [cmds] \Tn [cmds]

  Default:               0

  Range:                 0-90

  Unit:                  1 minute

  Description:           Sets the length of time that the modem does not
                         receive information before it disconnects.

                             INACTIVITY TIMER

  Type:                  Register

  Format:                AT [cmds] S90=n [cmds]

  Default:               0

  Range:                 0-255

  Unit:                  1 second

  Description:           Sets the length of time that the modem does not
                         receive information before it disconnects; S90=0
                         will disable.

                        INITIATE MNP RELIABLE MODE

  Type:          Immediate

  Format:        AT [cmds] \O [cmds]

  Description:   Initiates MNP reliable mode from normal

                             LOCK SERIAL PORT

  Type:          Configuration

  Format:        AT [cmds] \Jn [cmds]

  Description:   Sets operation of serial port speed

    Command                              Function

      \J0        Serial speed locked

      \J1        Serial speed follows connect speed

                    MAXIMUM BLOCK SIZE FOR TRANSMISSION

  Type:          Configuration

  Format:        AT [cmds] \An [cmds]

  Description:   Sets the maximum transmittable block size

    Command                              Function

      \A0        MNP block size is 64 characters

      \A1        MNP block size is 128 characters

      \A2        MNP block size is 192 characters

      \A3        MNP block size is 256 characters

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product identification code

       I1        Reports ROM checksum

       I2        Internal memory test

       I3        Reports device ID

       I4        Reports internal ID

                           SWITCH TO NORMAL MODE

  Type:          Immediate

  Format:        AT [cmds] \Z [cmds]

  Description:   Switches to normal mode from MNP mode

                                TEST MODES

  Type:              Register

  Format:            AT [cmds] S16=n [cmds]

  Default:           Unidentified

  Range:             0-125

  Unit:              Bit-mapped

  Description:       Controls loopback tests, analog, digital, remote
                     digital, and self tests.

   Bit      Value                          Function

    0            0   Local analog loopback not in progress

                1    Local analog loopback in progress

    1           0    Not used

    2            0   Local digital loopback not in progress

                1    Local digital loopback in progress

    3            0   Modem not in remote digital loopback

                1    Remote digital loopback in progress

    4            0   Remote digital loopback not requested

                1    Remote digital loopback requested

    5            0   Remote digital loopback w/ self-test not in progress

                1    Remote digital loopback w/ self-test in progress

    6            0   Local analog loopback w/ self-test not in progress

                1    Local analog loopback w/ self-test in progress

                          V.42 - DETECTION PHASE

  Type:          Configuration

  Format:        AT [cmds] -Jn [cmds]

  Description:   Controls V.42 detection

    Command                              Function

      -J0        V.42 detection disabled

      -J1        V.42 detection enabled

                       V.42bis - COMPRESSION CONTROL

  Type:          Configuration

  Format:        AT [cmds] "Hn [cmds]

  Description:   Controls V.42bis data compression

    Command                              Function

      "H0        V.42bis disabled

      "H1        V.42bis when transmitting enabled

      "H2        V.42bis when receiving enabled

      "H3        V.42bis when transmitting/receiving enabled

                      V.42bis - MAXIMUM STRING LENGTH

  Type:          Immediate

  Format:        AT [cmds] "On [cmds]

  Default:       16

  Range:         6-250

  Unit:          Characters

  Description:   Selects string size for V.42bis compression

                           XON/XOFF PASS-THROUGH

  Type:          Configuration

  Format:        AT [cmds] \Xn [cmds]

  Description:   Selects whether XON/XOFF signals are sent to remote
                 modem

    Command                              Function

      \X0        XON/XOFF signals trapped by local modem

      \X1        XON/XOFF passed through local modem

