
CREATIX POLYMEDIA

PCMCIA 14.4 FAXMODEM

Card Type                    Modem (asynchronous)
Chip Set                     Unidentified
Maximum Data Rate            14.4Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     PCMCIA Type II
Fax Class                    Class I
Data Modulation Protocol     Bell 103A/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis
Fax Modulation Protocol      ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis

                                                                      V1892

                         Proprietary AT Command Set

                    AUTO-RETRAIN - FALLBACK/FALLFORWARD

  Type:                Configuration

  Format:              AT [cmds] %En [cmds]

  Description:         Controls auto-retrain mode and fallback/fall
                       forward

       Command                             Function

         %E0           Auto-retrain disabled

         %E1           Auto-retrain enabled

         %E2           Fallback/fall forward enabled

         %E3           Auto-retrain enabled but modem will disconnect if
                       EQM reaches hang-up threshold

                                BREAK SEND

  Type:          Configuration

  Format:        AT [cmds] \Bn [cmds]

  Default:       3

  Range:         Unidentified

  Unit:          .1 second

  Description:   Sends break to modem

                               BREAK TYPE

  Type          Configuration

  Format        AT [cmds] \Kn [cmds]

  Default       5

  Range         1-5

  Description   Configures action of break signal

                                COMPRESSION

  Type:          Configuration

  Format:        AT %Cn

  Description:   Selects data compression

    Command                              Function

      %C0        Data compression disabled

      %C1        MNP5 enabled

      %C2        V.42bis enabled

      %C3        MNP5 and V.42bis enabled

                           COMPROMISE EQUALIZER

  Type:          Configuration

  Format:        AT [cmds] :En [cmds]

  Description:   Controls V.32 compromise equalizer

    Command                              Function

      :E0        Equalizer disabled

      :E1        Equalizer enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Sets connect mode

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        Reliable mode enabled

      \N3        Auto-reliable mode enabled

      \N4        LAPM mode enabled

      \N5        MNP mode enabled

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] \Gn [cmds]

  Description:   Selects modem port flow control

    Command                              Function

      \G0        Flow control disabled

      \G1        Flow control enabled

                    MAXIMUM BLOCK SIZE FOR TRANSMISSION

  Type:          Configuration

  Format:        AT [cmds] \An [cmds]

  Description:   Sets the maximum transmittable block size

    Command                              Function

      \A0        MNP block size is 64 characters

      \A1        MNP block size is 128 characters

      \A2        MNP block size is 192 characters

      \A3        MNP block size is 256 characters

                           MNP STREAM/BLOCK MODE

  Type:          Configuration

  Format:        AT [cmds] \Ln [cmds]

  Description:   Selects the transfer mode for MNP

    Command                              Function

      \L0        Stream mode for MNP enabled

      \L1        Block mode for MNP enabled

                             MNP10 COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] -Kn [cmds]

  Description:   Selects MNP10 data compression from V.42 LAPM

    Command                              Function

      -K0        MNP10 disabled

      -K1        MNP10 enabled

      -K2        MNP10 enabled on originate mode only

                              MNP10 FALLBACK

  Type:          Configuration

  Format:        AT [cmds] -Qn [cmds]

  Description:   Allows MNP10 to fallback to speeds slower than 4800bps

    Command                              Function

      -Q0        MNP10 at 2400 and 1200bps disabled

      -Q1        MNP10 at 2400 and 1200bps enabled

                          MNP10 LINK NEGOTIATION

  Type:          Configuration

  Format:        AT [cmds] *Hn [cmds]

  Description:   Sets the speed at which MNP10 link negotiation will
                 occur

    Command                              Function

      *H0        Link will be negotiated at highest possible speed

      *H1        Link will be negotiated at 1200bps

      *H2        Link will be negotiated at 4800bps

                         MNP10 POWER LEVEL ADJUST

  Type:                Configuration

  Format:              AT [cmds] )Mn [cmds]

  Description:         Controls automatic transmit power level adjustment
                       during MNP 10 link negotiation

       Command                              Function

         )M0           Power level adjustment disabled

         )M1           Power level adjustment enabled

                         REPORT LINE SIGNAL LEVEL

  Type:          Immediate

  Format:        AT [cmds] %L [cmds]

  Description:   Returns received line signal level

                        REPORT LINE SIGNAL QUALITY

  Type:          Immediate

  Format:        AT [cmds] %Q [cmds]

  Description:   Reports line signal quality

                            TRANSMISSION LEVEL

  Type:          Configuration

  Format:        AT [cmds] @Mn [cmds]

  Default:       0

  Range:         11-31

  Unit:          -1dBm

  Description:   Sets the initial signal level for transmission

    Command                              Function

      @M0        -26dBm

      @M1        -30dBm

    @M2-@M10     -10dBm

