
KINGSTON

KFM-PC144

Card Type                    Fax, Modem (asynchronous)
Chip Set                     Unidentified
Maximum Data Rate            14.4Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     PCMCIA Type II
Fax Class                    Class I
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis
Fax Modulation Protocol      ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis

                                                                      V1912

                         Proprietary AT Command Set

                 AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

  Type:          Configuration

  Format:        AT [cmds] %En [cmds]

  Description:   Controls auto-retrain mode and fallback/fall-forward

    Command                              Function

      %E0        Auto-retrain disabled

      %E1        Auto-retrain enabled

      %E2        Auto-fallback/fall-forward enabled

                          BIT-MAPPED REGISTER S14

  Format:             AT [cmds] S14=n [cmds]

  Default:            138

  Range:              0-174

  Unit:               Bit-mapped

  Description:        Controls echo, result codes and display, dial mode,
                      and answer/originate mode.

   Bit       Value                         Function

    0             0   Not used

    1              0  Command echo disabled

                  1   Command echo enabled

    2              0  Result codes enabled

                  1   Result codes disabled

    3              0  Display result codes in numeric format

                  1   Display result codes in verbose format

    4             0   Not used

    5              0  Tone dial enabled

                  1   Pulse dial enabled

    6             0   Not used

    7              0  Answer mode enabled

                  1   Originate mode enabled

                          BIT-MAPPED REGISTER S21

  Format                AT [cmds] S21=n [cmds]

  Default:              52

  Range:                0-252

  Unit:                 Bit-mapped

  Description:          Selects CTS/DCD/DSR signals, low DTR action, and
                        the long space disconnect function.

    Bit       Value                         Function

   0, 1           00    Not used

     2              0   CTS forced high

                   1    CTS follows RTS

   4, 3            00   DTR signal ignored

                   01   Modem goes to command mode on low DTR

                   10   Modem disconnects on low DTR; Auto-Answer is
                        disabled.
                  11
                        Modem is initialized on low DTR

     5              0   DCD forced high

                   1    DCD normal

     6              0   DSR forced high

                   1    DSR normal

     7              0   Long space disconnect function disabled

                   1    Long space disconnect function enabled

                          BIT-MAPPED REGISTER S22

  Format            AT [cmds] S22=n [cmds]

  Default:          117

  Range:            0-127

  Unit:             Bit-mapped

  Description:      Controls speaker volume and controls, and limits
                    results codes.

   Bit     Value                          Function

  1, 0         00   Volume off

               01   Low level volume

               10   Medium level volume

              11    High level volume

  3, 2         00   Speaker off

               01   Speaker off on carrier

               10   Speaker always on

              11    Speaker on during handshake

  6 - 4       000   Basic result codes only enabled

              100   Basic and connection speed result codes enabled

              101   Basic and connection speed result codes and dialtone
                    detection enabled
              110
                    All result codes except dialtone detection enabled
             111
                    All result codes enabled

                          BIT-MAPPED REGISTER S23

  Format                AT [cmds] S23=n [cmds]

  Default:              183

  Range:                0-189

  Unit:                 Bit-mapped

  Description:          Grants/denies remote digital loopback, controls
                        DTE rate and parity, and sets guard tone.

    Bit       Value                         Function

     0              0   Remote digital loopback denied

                   1    Remote digital loopback allowed

   3 - 1          000   Sets serial port speed to 0-300bps

                  001   Sets serial port speed to 600bps

                  010   Sets serial port speed to 1200bps

                  011   Sets serial port speed to 2400bps

                  100   Sets serial port speed to 4800bps

                  101   Sets serial port speed to 9600bps

                 110    Sets serial port speed to 19200bps

   5, 4            00   Parity even

                   01   Not used

                   10   Parity odd

                  11    No Parity

   7, 6            00   Guard tone disabled

                   01   Guard tone disabled

                  10    Guard tone 1800Hz enabled

                          BIT-MAPPED REGISTER S27

  Format               AT [cmds] S27=n [cmds]

  Default:             9

  Range:               0-75

  Unit:                Bit-mapped

  Description:         Selects asynchronous mode and ITU-T/Bell modes.

    Bit      Value                          Function

  3, 1, 0        000   Asynchronous mode, serial port speed follows
                       connect speed
                 101
                       Error correction mode
                111
                       Buffered asynchronous mode

  5, 4, 2       000    Not used

     6             0   ITU/T mode

                  1    Bell mode

                          BIT-MAPPED REGISTER S28

  Format             AT [cmds] S28=n [cmds]

  Default:           0

  Range:             0-128

  Unit:              Bit-mapped

  Description:       Controls MNP10 link negotiation.

   Bit      Value                          Function

  5 - 0    000000    Not used

   7, 6         00   Link will be negotiated at highest possible speed

                01   Link will be negotiated at 1200bps

               10    Link will be negotiated at 4800bps

                          BIT-MAPPED REGISTER S31

  Format:            AT [cmds] S31=n [cmds]

  Default:           194

  Range:             0-202

  Description:       Select auto-mode and extended result code format.

     Bit       Value                        Function

      0            0    Not used

      1             0   Auto-mode detection disabled

                   1    Auto-mode detection enabled

     3, 2          00   Enables CONNECT result codes to report DTE speed

                   01   Full reporting of CONNECT result codes

                  10    Enables CONNECT result codes to report DCE speed

    7 - 4       1100    Not used

                          BIT-MAPPED REGISTER S40

  Format                AT [cmds] S40=n [cmds]

  Default:              105

  Range:                0-238

  Unit:                 Bit-mapped

  Description:          Controls MNP extended services, power level
                        adjustment, break handling, and block size.

    Bit       Value                         Function

   0, 1            00   Conversion disabled

                   01   Conversion enabled

                  10    Conversion enabled except during LAPM answer
                        detection phase.

     2              0   Power level adjustment enabled

                   1    Power level adjustment disabled

  5, 4, 3         000   \K0

                  001   \K1

                  010   \K2

                  011   \K3

                  100   \K4

                 101    \K5

   7, 6            00   MNP block size is 64 characters

                   01   MNP block size is 128 characters

                   10   MNP block size is 192 characters

                  11    MNP block size is 256 characters

                          BIT-MAPPED REGISTER S41

  Format             AT [cmds] S41=n [cmds]

  Default:           131

  Range:             0-219

  Unit:              Bit-mapped

  Description:       Selects compression, auto-retrain, flow control, MNP
                     mode and MNP10 fallback.

   Bit      Value                          Function

  1, 0           00  Data compression disabled

                 01  MNP5 enabled

                 10  V.42bis enabled

                11   MNP5 and V.42bis enabled

  6, 2           00  Auto-retrain disabled

                 01  Auto-retrain enabled

                10   Auto-fallback/fall-forward enabled

    3             0  Flow control disabled

                 1   Flow control enabled

    4             0  Stream mode for MNP

                 1   Block mode for MNP

    5            0   Not used

    7             0  MNP10 at 2400 and 1200bps disabled

                 1   MNP10 at 2400 and 1200bps enabled

                         BIT-MAPPED REGISTER S201

  Format:             AT [cmds] S201=n [cmds]

  Default:            58

  Range:              0-62

  Description:        Controls power level, and compromise equalizer.

     Bit        Value                        Function

    4 - 0          00000  Initial power level -26dBm

                   00001  Initial power level -30dBm

                   00010  Initial power level -10dBm

                     ...  ...

                   01010  Initial power level -10dBm

                   01011  Initial power level -11dBm

                ...to...  ...to...

                   11010  Initial power level -26dBm

                ...to...  ...to...

                  11110   Initial power level -30dBm

      5                0   Equalizer disabled

                      1    Equalizer enabled

                                BREAK SEND

  Type:          Configuration

  Format:        AT [cmds] \Bn [cmds]

  Default:       3

  Range:         1-9

  Unit:          .1 second

  Description:   Sends break to modem

                                BREAK TYPE

  Type:                    Configuration

  Format:                  AT [cmds] \Kn [cmds]

  Description:             Configures action of break signal

     Command       Break from DTE     Modem receives      Break received
                                            \B          from remote modem

       \K0        Online command     Break sent to      Buffers cleared,
                  mode enabled,      remote modem and   break sent to DTE
                  send no break      buffered cleared
                  to remote modem

       \K1        Break sent to      Break sent to      Buffers cleared,
                  remote modem       remote modem and   break sent to DTE
                  and buffered       buffered cleared
                  cleared

       \K2        Online command     Send break to      Break sent
                  mode enabled,      remote modem       immediately to
                  send no break      immediately        DTE
                  to remote modem

       \K3        Send break to      Send break to      Break sent
                  remote modem       remote modem       immediately to
                  immediately        immediately        DTE

       \K4        Online command     Send break with    Break sent with
                  mode enabled,      transmitted data   received data to
                  send no break                         the DTE
                  to remote modem

       \K5        Send break with    Send break with    Break sent with
                  transmitted        transmitted data   received data to
                  data                                  the DTE

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] %Cn [cmds]

  Description:   Selects data compression

    Command                              Function

      %C0        Data compression disabled

      %C1        MNP5 enabled

      %C2        V.42bis enabled

      %C3        MNP5 and V.42bis enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Normal mode enabled

      \N2        Reliable mode enabled

      \N3        Auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

      \N5        MNP auto-reliable mode enabled

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Modifier                             Function

           L             Re-dial last number

           P             Pulse dialing enabled

           Sn            Dial stored telephone number n (n=1-3)

          S=n            Dial stored telephone number n (n=1-3)

           T             Tone dialing enabled

           W             Dialing resumed following dial tone detection

           ,             Dialing paused for amount of time specified in
                         S8 register

           @             Wait for quiet answer

           ;             Modem returned to command state after dialing

           !             Modem commanded to go on-hook for specified time
                         before returning off-hook.

           ^             Calling tone disabled for this call only

                         FLASH DIAL MODIFIER TIME

  Type:                Register

  Format               AT [cmds] S29=n [cmds]

  Default:             0

  Range:               0-255

  Unit:                .01 second

  Description:         Time the modem will go on-hook upon receiving the
                       ! dial modifier in dial string.

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] \Gn [cmds]

  Description:   Selects modem port flow control

    Command                              Function

      \G0        Flow control disabled

      \G1        Flow control enabled

                               FLOW CONTROL

  Type:          Read-only Register

  Format         AT [cmds] S39? [cmds]

  Description:   Displays the current flow control

     Value                               Meaning

       0         Flow control disabled

       3         RTS/CTS flow control enabled

       4         XON/XOFF flow control enabled

       5         XON/XOFF and RTS/CTS flow control enabled

                       FLOW CONTROL CHARACTER - XOFF

  Type:          Register

  Format:        AT [cmds] S33=n [cmds]

  Default:       19

  Range:         0-255

  Unit:          ASCII

  Description:   Sets the character used to represent XOFF

                       FLOW CONTROL CHARACTER - XON

  Type:          Register

  Format:        AT [cmds] S32=n [cmds]

  Default:       17

  Range:         0-255

  Unit:          ASCII

  Description:   Sets the character used to represent XON

                             INACTIVITY TIMER

  Type:                   Register

  Format                  AT [cmds] S30=n [cmds]

  Default:                0

  Range:                  0-255

  Unit:                   10 seconds

  Description:            Maximum duration of DTE and DCE inactivity
                          allowed prior to initiating hang-up process.
                          S30=0 will disable timer.

                             LINE SIGNAL LEVEL

  Type:           Immediate

  Format:         AT [cmds] %L [cmds]

  Description:    Returns a value which indicates the received line
                  signal level

                            LINE SIGNAL QUALITY

  Type:          Immediate

  Format:        AT [cmds] %Q [cmds]

  Description:   Returns a value which indicates line signal quality

                             LOCK SERIAL PORT

  Type:          Configuration

  Format:        AT [cmds] \Jn [cmds]

  Description:   Sets operation of serial port speed

    Command                              Function

      \J0        Serial speed locked

      \J1        Serial speed follows connect speed

                    MAXIMUM BLOCK SIZE FOR TRANSMISSION

  Type:          Configuration

  Format:        AT [cmds] \An [cmds]

  Description:   Sets the maximum transmittable block size

    Command                              Function

      \A0        MNP block size is 64 characters

      \A1        MNP block size is 128 characters

      \A2        MNP block size is 192 characters

      \A3        MNP block size is 256 characters

                          MNP - EXTENDED SERVICES

  Type:           Configuration

  Format:         AT [cmds] -Kn [cmds]

  Description:    Controls conversion of a LAPM connection to MNP10
                  connection

    Command                              Function

      -K0         Conversion disabled

      -K1         Conversion enabled

      -K2         Conversion enabled except during LAPM answer detection
                  phase.

                          MNP - STREAM/BLOCK MODE

  Type:          Configuration

  Format:        AT [cmds] \Ln [cmds]

  Description:   Selects the transfer mode for MNP link

    Command                              Function

      \L0        Stream mode for MNP enabled

      \L1        Block mode for MNP enabled

                             MNP10 - FALLBACK

  Type:          Configuration

  Format:        AT [cmds] -Qn [cmds]

  Description:   Allows MNP10 to fall back to speeds slower than 4800bps

    Command                              Function

      -Q0        MNP10 at 2400 and 1200bps disabled

      -Q1        MNP10 at 2400 and 1200bps enabled

                         MNP10 - LINK NEGOTIATION

  Type:          Configuration

  Format:        AT [cmds] *Hn [cmds]

  Description:   Sets the speed at which MNP10 link negotiation will
                 occur

    Command                              Function

      *H0        Link will be negotiated at highest possible speed

      *H1        Link will be negotiated at 1200bps

      *H2        Link will be negotiated at 4800bps

                        MNP10 - POWER LEVEL ADJUST

  Type:                Configuration

  Format:              AT [cmds] )Mn [cmds]

  Description:         Controls automatic transmit power level adjustment
                       during MNP 10 link negotiation

       Command                              Function

         )M0           Power level adjustment disabled

         )M1           Power level adjustment enabled

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports ROM checksum

       I2        Tests ROM and reports OK or ERROR

       I3        Reports ROM revision level

       I4        Reports modem identifier string

       I5        Report country code

       I6        Reports data pump model

                                SLEEP TIMER

  Type:                   Register

  Format                  AT [cmds] S24=n [cmds]

  Default:                32

  Range:                  0-255

  Unit:                   1 second

  Description:            Maximum duration of DTE and DCE inactivity
                          allowed prior to initiating low-power sleep
                          mode. S24=0 will disable timer.

                                TEST MODES

  Type:              Register

  Format:            AT [cmds] S16=n [cmds]

  Default:           0

  Range:             0-125

  Unit:              Bit-mapped

  Description:       Controls loopback tests, analog, digital, remote
                     digital, and self tests.

   Bit      Value                          Function

    0            0   Local analog loopback not in progress

                1    Local analog loopback in progress

    1           0    Not used

    2            0   Local digital loopback not in progress

                1    Local digital loopback in progress

    3            0   Modem not in remote digital loopback

                1    Remote digital loopback in progress

    4            0   Remote digital loopback not requested

                1    Remote digital loopback requested

    5            0   Remote digital loopback w/ self-test not in progress

                1    Remote digital loopback w/ self-test in progress

    6            0   Local analog loopback w/ self-test not in progress

                1    Local analog loopback w/ self-test in progress

                       TRANSMISSION LEVEL - CELLULAR

  Type:           Configuration

  Format:         AT [cmds] @Mn [cmds]

  Default:        26

  Range:          0-31

  Unit:           -1dBm

  Description:    Sets the signal level for transmission while in
                  cellular mode

    Command                              Function

      @M0         -26 dBm

      @M1         -30 dBm

    @M2-@M10      -10 dBm

                                 V.23 MODE

  Type:          Configuration

  Format:        AT [cmds] %Fn [cmds]

  Description:   Selects V.23 split-speed and half-duplex

    Command                              Function

      %F1         75bps transmit, 1200bps receive (split-speed)

      %F2         1200bps transmit, 75bps receive (split-speed)

                        V.32 - COMPROMISE EQUALIZER

  Type:          Configuration

  Format:        AT [cmds] :En [cmds]

  Description:   Controls V.32 compromise equalizer

    Command                              Function

      :E0        Equalizer disabled

      :E1        Equalizer enabled

