
STOLLMANN GMBH

TA-DD

Card Type                ISDN TA
Chip Set                 Unidentified
Maximum Data Rate        64Kbps x 2
Data Bus                 External
ISDN Modulation Protocol V.110, 1TR6, DSS1, X.30

[Image]

                                CONNECTIONS

         Function           Label             Function             Label

  Line out                       CN1       V.24 or X.21 port 1      CN4

  DC power                       CN2       Reset button             SW1

  V.24 or X.21 port 2            CN3

            Note: X.21 functionality is provided by an included adapter
            cable.

                        USER CONFIGURABLE SETTINGS

                    Setting                       Label       Position

  Editor debug mode disabled                        J3          Open

  Editor debug mode enabled                         J3         Closed

  TA will use saved profile                         J4          Open

  TA will use default profile only                  J4         Closed

  Remote configuration enabled                      J6          Open

  Remote configuration disabled                     J6         Closed

  Port 1 is in V.24 mode                            J9          Open

  Port 1 is in X.21 mode                            J9         Closed

  Port 2 is in V.24 mode                           J10          Open

  Port 2 is in X.21 mode                           J10         Closed

  Port 1 is in DCE mode                            J13         Closed

  Port 1 is in DTE mode                            J13          Open

  Pin 25 of port 1 is not connected                J13A         Open

  Pin 25 of port 1 is +9V DC                       J13A        Closed

  Port 2 is in DCE mode                            J14         Closed

  Port 2 is in DTE mode                            J14          Open

  Pin 25 of port 2 is not connected                J14A         Open

  Pin 25 of port 2 is +9V DC                       J14A        Closed

  Pin 1 of port 1 is capacitive ground             JN1          Open

  Pin 1 of port 1 is galvanic ground               JN1         Closed

  Pin 1 of port 2 is capacitive ground             JN2          Open

  Pin 1 of port 2 is galvanic ground               JN2         Closed

  Factory configured - do not alter                 J5       Unidentified

  Factory configured - do not alter                 J7       Unidentified

  Factory configured - do not alter                 J8       Unidentified

                     ISDN INTERFACE TYPE

       Setting               J11                  J12

     S-interface       Pins 1 & 2 closed   Pins 1 & 2 closed

     U-interface       Pins 2 & 3 closed   Pins 2 & 3 closed

                          LINE TYPE

       Setting                J1                  J2

     Public ISDN             Open                Open

      ISDN PBX              Closed               Open

  ISDN PBX with LLC          Open               Closed

                             DIAGNOSTIC LED(S)

                   LED1 Status                           Condition

                       On                               Power is on

                       Off                              Power is off

                    Blinking                            ISDN failed

   LED2 Status     LED3 Status     LED4 Status           Condition

       Off             Off             Off          Normal operation for
                                                         channel 1

       On              Off             Off             ISDN connection
                                                   established on channel
                                                             1

   Alternating     Alternating         Off              Hotline call
                                                   repetition in progress
                                                        on channel 1

    Blinking         Blinking          Off              Hotline call
                                                     repetition error on
                                                         channel 1

    Blinking           Off             Off         Hotline active without
                                                    connection on channel
                                                             1

       On              Off             Off          Profile editor in use
                                                    locally on channel 1

       On               On              On             Profile editor
                                                   password being entered
                                                        on channel 1

       On            Blinking        Blinking       Profile editor in use
                                                   remotely on channel 1

       Off             Off              On           Unable to determine
                                                     correct connection
                                                     rate on channel 1

       Off              On             Off          Buffer has overflowed
                                                        on channel 1

   Alternating       Blinking      Alternating       Checksum error has
                                                      been detected on
                                                         channel 1

   LED5 Status     LED6 Status     LED7 Status           Condition

       Off             Off             Off          Normal operation for
                                                         channel 2

       On              Off             Off             ISDN connection
                                                   established on channel
                                                             2

   Alternating     Alternating         Off              Hotline call
                                                   repetition in progress
                                                        on channel 2

    Blinking         Blinking          Off              Hotline call
                                                     repetition error on
                                                         channel 2

    Blinking           Off             Off         Hotline active without
                                                    connection on channel
                                                             2

       On              Off             Off          Profile editor in use
                                                    locally on channel 2

       On               On              On             Profile editor
                                                   password being entered
                                                        on channel 2

       On            Blinking        Blinking       Profile editor in use
                                                   remotely on channel 2

       Off             Off              On           Unable to determine
                                                     correct connection
                                                     rate on channel 2

       Off              On             Off          Buffer has overflowed
                                                        on channel 2

   Alternating       Blinking      Alternating       Checksum error has
                                                      been detected on
                                                         channel 2

  LED2    LED3    LED4    LED5     LED6    LED7          Condition

  Blink    Off     Off    Blink    Off     Off        TA is resetting

                         Proprietary AT Command Set

                             AUTO-ANSWER TIME

  Type:                  Register

  Format:                AT [cmds] S0=n [cmds]

  Default:               Unidentified

  Range:                 0-24

  Unit:                  5 seconds

  Description:           Sets the amount of time that will elapse before
                         the TA will answer an incoming call. When this
                         value is set to 0 the TA will not automatically
                         answer calls. A value of 1 will answer
                         immediately. Values greater than 1 set the time
                         to (n-1) * 5 seconds.

                                CTS SIGNAL

  Type:          Configuration

  Format:        AT [cmds] &Rn [cmds]

  Description:   Controls the operation of the Clear to Send signal.

    Command                              Function

      &R0         CTS follows RTS.

      &R1         CTS forced high.

      &R2         CTS follows V.110 flow control.

                             FLOW CONTROL MODE

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Sets the type of flow control used.

    Command                              Function

      &K0         Flow control disabled.

      &K3         CTS/RTS flow control enabled.

      &K4         XON/XOFF flow control enabled.

      &K5         Flow control disabled.

                               RESULT CODES

  Type:          Register

  Format:        AT [cmds] S15=n [cmds]

  Description:   Enables caller ID information and extended result codes.

    Command                              Function

     S15=0        Caller ID information and extended result codes
                  disabled.

     S15=1        Caller ID information enabled.

     S15=3        Caller ID information and extended result codes
                  enabled.

                          BIT-MAPPED REGISTER S14

  Format:            AT [cmds] S14=n [cmds]

  Default:           Unidentified

  Range:             0-14

  Description:       Controls echo mode and result codes.

     Bit      Value                         Function

      0            0   Not used.

      1             0   Command echo disabled.

                   1    Command echo enabled.

      2             0   Result codes enabled.

                   1    Result codes disabled.

      3             0   Numerical result codes enabled.

                   1    Verbose result codes enabled.

                          Proprietary Command Set

                              COMMAND ECHOING

  Type:          Configuration

  Format:        Jn

  Description:   Selects whether commands will be echoed back to the DTE.

    Command                              Function

       J0         Command echoing disabled.

       J1         Command echoing enabled.

                             CONNECTION SPEED

  Type:          Configuration

  Format:        Hn

  Description:   Sets the speed of the remote connection.

    Command                              Function

       H1         Set speed to 300bps.

       H2         Set speed to 600bps.

       H3         Set speed to 1200bps.

       H4         Set speed to 2400bps.

       H5         Set speed to 4800bps.

       H6         Set speed to 9600bps.

       H7         Set speed to 19.2Kbps.

       H8         Set speed to 38.4Kbps.

                          CHANGE PROFILE CHANNEL

  Type:          Configuration

  Format:        PROn

  Description:   Selects which channels profile is being edited.

    Command                              Function

      PRO1        Edit profile for channel 1.

      PRO2        Edit profile for channel 2.

                        CTS SIGNAL - NO CONNECTION

  Type:              Configuration

  Format:            NCTS 0xhh

  Description:       Controls the behaviour of the CTS signal when there
                     is no ISDN connection.

      Command                              Function

     NCTS 0x01        CTS is forced low.

     NCTS 0x02        CTS is forced high.

     NCTS 0x04        CTS follows DTR.

     NCTS 0x08        CTS follows RTS.

     NCTS 0x10        CTS is forced high during connection and
                      negotiation only.

     NCTS 0x20        CTS follows remote DTR.

     NCTS 0x40        CTS follows remote RTS.

     NCTS 0x80        CTS follows V.110 flow control.

                         CTS SIGNAL - NEGOTIATION

  Type:                 Configuration

  Format:               WCTS 0xhh

  Description:          Controls the behaviour of the CTS signal while
                        dialing and negotiating a connection.

        Command                             Function

       WCTS 0x01        CTS is forced low.

       WCTS 0x02        CTS is forced high.

       WCTS 0x04        CTS follows DTR.

       WCTS 0x08        CTS follows RTS.

       WCTS 0x10        CTS is forced high during connection and
                        synchronization only.

       WCTS 0x20        CTS follows remote DTR.

       WCTS 0x40        CTS follows remote RTS.

       WCTS 0x80        CTS follows V.110 flow control.

                          CTS SIGNAL - CONNECTION

  Type:           Configuration

  Format:         CCTS 0xhh

  Description:    Controls the behaviour of the CTS signal while
                  connected.

     Command                              Function

    CCTS 0x01      CTS is forced low.

    CCTS 0x02      CTS is forced high.

    CCTS 0x04      CTS follows DTR.

    CCTS 0x08      CTS follows RTS.

    CCTS 0x10      CTS is forced high during connection and
                   synchronization only.

    CCTS 0x20      CTS follows remote DTR.

    CCTS 0x40      CTS follows remote RTS.

    CCTS 0x80      CTS follows V.110 flow control.

                                DATA LENGTH

  Type:          Configuration

  Format:        Ln

  Description:   Selects how many data bits will be transmitted.

    Command                              Function

       L0         Synchronous mode.

       L7         7 data bits.

       L8         8 data bits.

                                DATA PARITY

  Type:          Configuration

  Format:        Mn

  Description:   Selects how many parity bits will be transmitted.

    Command                              Function

       M0         No parity.

       M1         Odd parity.

       M2         Even parity.

                                 DATA STOP

  Type:          Configuration

  Format:        Nn

  Description:   Selects how many stop bits will be transmitted.

    Command                              Function

       M1         1 stop bit.

       M2         2 stop bits.

                        DCD SIGNAL - NO CONNECTION

  Type:              Configuration

  Format:            NDCD 0xhh

  Description:       Controls the behavior of the DCD signal when there
                     is no ISDN connection.

      Command                              Function

     NDCD 0x01       DCD is forced low.

     NDCD 0x02       DCD is forced high.

     NDCD 0x04       DCD follows DTR.

     NDCD 0x08       DCD follows RTS.

     NDCD 0x10       DCD is forced high during connection and negotiation
                     only.

     NDCD 0x20       DCD follows remote DTR.

     NDCD 0x40       DCD follows remote RTS.

     NDCD 0x80       DCD follows V.110 flow control.

                         DCD SIGNAL - NEGOTIATION

  Type:                 Configuration

  Format:               WDCD 0xhh

  Description:          Controls the behavior of the DCD signal while
                        dialing and negotiating a connection.

       Command                              Function

      WDCD 0x01         DCD is forced low.

      WDCD 0x02         DCD is forced high.

      WDCD 0x04         DCD follows DTR.

      WDCD 0x08         DCD follows RTS.

      WDCD 0x10         DCD is forced high during connection and
                        synchronization only.

      WDCD 0x20         DCD follows remote DTR.

      WDCD 0x40         DCD follows remote RTS.

      WDCD 0x80         DCD follows V.110 flow control.

                          DCD SIGNAL - CONNECTION

  Type:           Configuration

  Format:         CDCD 0xhh

  Description:    Controls the behaviour of the DCD signal while
                  connected.

     Command                              Function

    CDCD 0x01      DCD is forced low.

    CDCD 0x02      DCD is forced high.

    CDCD 0x04      DCD follows DTR.

    CDCD 0x08      DCD follows RTS.

    CDCD 0x10      DCD is forced high during connection and
                   synchronization only.

    CDCD 0x20      DCD follows remote DTR.

    CDCD 0x40      DCD follows remote RTS.

    CDCD 0x80      DCD follows V.110 flow control.

                               DEBUG PROFILE

  Type:          Immediate

  Format:        TEST

  Description:   Displays the profile editor debug page.

                                 DIAL MODE

  Type:          Configuration

  Format:        En

  Description:   Selects the dial mode the TA will use.

    Command                              Function

       E1         Manual dialing only; prompt for number will be
                  displayed.

       E2         Asynchronous V.25bis dial mode.

       E3         Hotline dial mode; DTR is used for call signalling.

       E4         Hotline dial mode; RTS is used for call signalling.

       E5         Hotline dial mode; automatic dial attempt.

       E6         Incoming calls only.

       E7         Hayes dialing mode.

       E8         Synchronous V.25bis dial mode.

                        DSR SIGNAL - NO CONNECTION

  Type:              Configuration

  Format:            NDSR 0xhh

  Description:       Controls the behaviour of the DSR signal when there
                     is no ISDN connection.

      Command                              Function

     NDSR 0x01        DSR is forced low.

     NDSR 0x02        DSR is forced high.

     NDSR 0x04        DSR follows DTR.

     NDSR 0x08        DSR follows RTS.

     NDSR 0x10        DSR is forced high during connection and
                      negotiation only.

     NDSR 0x20        DSR follows remote DTR.

     NDSR 0x40        DSR follows remote RTS.

     NDSR 0x80        DSR follows V.110 flow control.

                         DSR SIGNAL - NEGOTIATION

  Type:                 Configuration

  Format:               WDSR 0xhh

  Description:          Controls the behaviour of the DSR signal while
                        dialing and negotiating a connection.

        Command                             Function

       WDSR 0x01        DSR is forced low.

       WDSR 0x02        DSR is forced high.

       WDSR 0x04        DSR follows DTR.

       WDSR 0x08        DSR follows RTS.

       WDSR 0x10        DSR is forced high during connection and
                        synchronization only.

       WDSR 0x20        DSR follows remote DTR.

       WDSR 0x40        DSR follows remote RTS.

       WDSR 0x80        DSR follows V.110 flow control.

                          DSR SIGNAL - CONNECTION

  Type:           Configuration

  Format:         CDSR 0xhh

  Description:    Controls the behaviour of the DSR signal while
                  connected.

     Command                              Function

    CDSR 0x01      DSR is forced low.

    CDSR 0x02      DSR is forced high.

    CDSR 0x04      DSR follows DTR.

    CDSR 0x08      DSR follows RTS.

    CDSR 0x10      DSR is forced high during connection and
                   synchronization only.

    CDSR 0x20      DSR follows remote DTR.

    CDSR 0x40      DSR follows remote RTS.

    CDSR 0x80      DSR follows V.110 flow control.

                               DTE/DCE MODE

  Type:          Configuration

  Format:        Sn

  Description:   Sets whether the TA will operate as a DTE or a DCE
                 device.

    Command                              Function

       S0         TA will operate as DCE.

       S1         TA will operate as DTE.

                                DTR SIGNAL

  Type:                  Configuration

  Format:                Dn

  Description:           Controls the operation of the Data Terminal
                         Ready signal.

        Command                              Function

           D0            Incoming calls accepted regardless of DTR state;
                         low DTR does not disconnect.

           D1            Incoming calls accepted only if DTR is high; DTR
                         or RTS transition to high will initiate a
                         hotline call if in hotline mode; low DTR
                         disconnects.

           D2            Incoming calls accepted only if DTR is high;
                         high DTR or RTS will initiate a hotline call if
                         in hotline mode; low DTR disconnects.

           D3            Incoming calls accepted regardless of DTR state;
                         DTR or RTS transition to high will initiate a
                         hotline call if in hotline mode; low DTR
                         disconnects.

           D4            Incoming calls accepted regardless of DTR state;
                         high DTR or RTS will initiate a hotline call if
                         in hotline mode; low DTR disconnects.

           D5            Incoming calls accepted only if DTR is high; DTR
                         or RTS transition to high will initiate a
                         hotline call if in hotline mode; low DTR does
                         not disconnect.

           D6            Incoming calls accepted only if DTR is high;
                         high DTR or RTS will initiate a hotline call if
                         in hotline mode; low DTR does not disconnect.

                                    EAZ

  Type:                  Configuration

  Format:                An

  Description:           Sets which incoming calls are answered.

        Command                              Function

           A0             All incoming calls are answered; all channels
                          are notified of the call.

        A1 - A8           Only calls with a matching EAZ are answered.

           A9             All incoming calls are answered; only the
                          channel matching the EAZ is notified of the
                          call.

                               EAZ - EDITOR

  Type:             Configuration

  Format:           Tn

  Description:      Sets which incoming calls should be routed for remote
                    configuration.

      Command                             Function

        T0          Only calls ending in "e" are routed to the editor.

      T1 - T8       Only calls with a matching EAZ are answered.

        T9          Calls matching the EAZ or ending in "e" are routed to
                    the editor.

                           ENTER PROFILE EDITOR

  Type:             Immediate

  Description:      Enters the profile editor so that changes may be
                    made.

       Mode                                Command

    Manual dial      <CR><ESC>

   V.25bis dial      <CR><ESC>

    Hayes dial       AT<CR><ESC>

  All other modes    Push reset button, then <CR><CR><ESC><ESC>

                            EXIT PROFILE EDITOR

  Type:          Immediate

  Format:        EXIT

                 <ESC>

  Description:   Quits the editor without saving changes.

                          FLOW CONTROL MODE - DCE

  Type:          Configuration

  Format:        Bn

  Description:   Sets the type of flow control used.

    Command                              Function

       B0         Flow control disabled.

       B1         XON/XOFF flow control enabled.

       B2         CTS flow control enabled.

                          FLOW CONTROL MODE - DTE

  Type:          Configuration

  Format:        Cn

  Description:   Sets the type of flow control used.

    Command                              Function

       C0         Flow control disabled.

       C1         XON/XOFF flow control enabled.

       C2         RTS flow control enabled.

       C3         DTR flow control enabled.

                              HOTLINE NUMBER

  Type:                  Configuration

  Format:                HOT <#>

  Description:           Sets the number for hotline calling. If no
                         number is given, hotline calling will not be
                         allowed.

                             INACTIVITY TIMER

  Type:                  Configuration

  Format:                Fn

  Default:               0

  Range:                 0 - 60

  Unit:                  1 minute

  Description:           Sets the amount of time that there must be no
                         activity on the ISDN line before the TA
                         disconnects.

                           INCOMING CALL NUMBER

  Type:          Configuration

  Format:        RUFn <#>

  Description:   Sets the number in position n of allowed incoming calls.

                                 LANGUAGE

  Type:          Configuration

  Format:        Kn

  Description:   Selects the language the TA will display messages in.

    Command                              Function

       K0         Messages will be displayed in English.

       K1         Messages will be displayed in German.

                                 LINE TYPE

  Type:          Configuration

  Format:        Rn

  Description:   Sets the type of line the TA will be operating on.

    Command                              Function

       R0         ISDN with BRI service.

       R1         Group 3 leased line service with 1TR6.

       R2         Group 2 leased line, 2B+D or B+D.

       R3         Group 0 leased line, single B channel only.

       R4         Point-to-point switched line.

       R5         Point-to-point group 3 leased line with 1TR6.

                              LLC - INCOMING

  Type:          Configuration

  Format:        Pn

  Description:   Sets the use of LLC for incoming DSS1 calls.

    Command                              Function

       P1         Only calls with matching LLC will be answered.

       P2         Ignore LLC when answering calls.

       P3         All data calls will be answered.

       P4         All calls will be answered.

                              LLC - OUTGOING

  Type:          Configuration

  Format:        On

  Description:   Sets the use of LLC for outgoing DSS1 calls.

    Command                              Function

       O1         Standard LLC enabled.

       O2         LLC disabled.

       O3         User-defined LLC enabled.

                       LLC - USER-DEFINED DATA OCTET

  Type:          Configuration

  Format:        LLC=hh hh hh..

  Description:   Sets the user-defined LLC octets in hexadecimal.

                          LOCAL SERIAL PORT SPEED

  Type:          Configuration

  Format:        Gn

  Description:   Sets the speed of the serial port.

    Command                              Function

       G1         Set speed to 300bps.

       G2         Set speed to 600bps.

       G3         Set speed to 1200bps.

       G4         Set speed to 2400bps.

       G5         Set speed to 4800bps.

       G6         Set speed to 9600bps.

       G7         Set speed to 19.2Kbps.

       G8         Set speed to 38.4Kbps.

                          LOCK SERIAL PORT SPEED

  Type:              Configuration

  Format:            In

  Description:       Selects whether the serial port speed will be
                     adjusted to the DTE speed.

      Command                              Function

         I0          Serial port speed locked.

         I1          Serial port speed will match DTE speed.

                                    MSN

  Type:              Configuration

  Format:            MALL <#>*n

  Description:       Sets the MSN and subaddress for both channels of the
                     TA and the editor.

                                 MSN - TA

  Type:          Configuration

  Format:        MTAX <#>*n

  Description:   Sets the MSN and subaddress for both channels of the TA.

                               MSN - EDITOR

  Type:           Configuration

  Format:         MEDX <#>*n

  Description:    Sets the MSN and subaddress for both channels of the
                  editor.

                          MSN - EDITOR CHANNEL 1

  Type:          Configuration

  Format:        MED1 <#>*n

  Description:   Sets the MSN and subaddress for channel 1 of the editor.

                          MSN - EDITOR CHANNEL 2

  Type:          Configuration

  Format:        MED2 <#>*n

  Description:   Sets the MSN and subaddress for channel 2 of the editor.

                            MSN - TA CHANNEL 1

  Type:          Configuration

  Format:        MTA1 <#>*n

  Description:   Sets the MSN and subaddress for channel 1 of the TA.

                            MSN - TA CHANNEL 2

  Type:          Configuration

  Format:        MTA2 <#>*n

  Description:   Sets the MSN and subaddress for channel 2 of the TA.

                                 NEXT PAGE

  Type:          Immediate

  Format:        NEXT

  Description:   Shows the next page of values.

                               PREVIOUS PAGE

  Type:          Immediate

  Format:        PREV

  Description:   Shows the previous page of values.

                       REMOTE CONFIGURATION PASSWORD

  Type:                  Configuration

  Format:                PWD xxxx

  Description:           Sets the password for remote configuration. If
                         no password is given, no password will be
                         required.

                         RESET TO FACTORY DEFAULTS

  Type:          Immediate

  Format:        DEFA

  Description:   Resets all settings to their factory defaults.

                               SAVE PROFILE

  Type:            Immediate

  Format:          SAVE

  Description:     Saves the current settings into the profile and quits
                   the editor.

                             SERVICE INDICATOR

  Type:          Configuration

  Format:        Pn

  Description:   Sets the 1TR6 Service Indicator.

    Command                              Function

       P0         Service Indicator reports standard line.

       P1         Service Indicator reports Private SI.

       P2         Service Indicator reports Private 2.

                         SERVICE INDICATOR DETAILS

  Type:                Configuration

  Format:              On

  Description:         Sets the details for the 1TR6 Service Indicator.

      Pn Setting          Command                   Function

          P0                 O1         Service Indicator reports 1TR6.

                             O2         Service Indicator reports X.21.

                             O3         Service Indicator reports AOI
                                        synch/asynch mode.

          P1                 O1         Service Indicator reports V.24
                                        asynch.

                             O2         Service Indicator reports 64Kbps
                                        asynch.

                             O3         Service Indicator reports V.24
                                        BTX.

                             O4         Service Indicator reports V.24
                                        Text.

                             O5         Service Indicator reports 64Kbps
                                        PC-Net.

          P2                 O1         Service Indicator reports Private
                                        2 LLC with the data octet equal
                                        to 0.

                             O2         Service Indicator reports Private
                                        2 LLC with the data octet not
                                        equal to 0.

                             O3         Service Indicator reports Private
                                        2 with the data octet equal to 0.

                             SYNCHRONOUS SPEED

  Type:              Configuration

  Format:            Qn

  Description:       Selects what data rate the TA will operate in when
                     in synchronous mode.

      Command                              Function

        Q0           Use V.24 asynchronous mode.

        Q1           Use data rate set with Gn and Hn.

        Q2           Use 64Kbps data rate.

        Q3           Use 56Kbps data rate.

        Q4           Use 48Kbps data rate.

                              UPDATE PROFILE

  Type:          Immediate

  Format:        UPDA

  Description:   Saves the current settings into the profile.

