
SIIG, INC.

DASH 14.4I FAX/MODEM INTERNAL

Card Type                    Fax, Modem (asynchronous)
Chip Set                     Unidentified
Maximum Data Rate            14.4Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     8-bit ISA
Fax Class                    Class I
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis
Fax Modulation Protocol      ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis

[Image]

                                CONNECTIONS

         Function            Label            Function             Label

  Phone line out                  CN1       Phone line in           CN2

                           SERIAL PORT ADDRESS

    Setting        JP1/D          JP1/E          JP1/F          JP1/G

  COM1 (3F8h)      Closed          Open         Closed          Open

  COM2 (2F8h)       Open          Closed        Closed          Open

  COM3 (3E8h)      Closed          Open          Open          Closed

  COM4 (2E8h)       Open          Closed         Open          Closed

            INTERRUPT SELECTION

  Setting    JP1/A      JP1/B      JP1/C

     3       Closed      Open      Open

     4        Open      Closed     Open

     5        Open       Open     Closed

                         Proprietary AT Command Set

                 AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

  Type:          Configuration

  Format:        AT [cmds] %En [cmds]

  Description:   Controls auto-retrain mode and fallback/fall-forward

    Command                              Function

      %E0        Auto-retrain disabled

      %E1        Auto-retrain enabled

      %E2        Auto-fallback/fall-forward enabled

  BIT MAPPED REGISTERS

  Register     Default

    S14          138

    S16           0

    S21           0

    S22          117

    S23          55

    S27          73

    S28           0

    S31           2

    S40          105

    S41           3

                                BREAK TYPE

  Type:           Configuration

  Format:         AT [cmds] \Kn [cmds]

  Description:    Configures action of break signal

    Command                              Function

      \K0         Online command mode enabled, send no break to remote
                  modem

      \K1         Break sent to remote modem and buffers cleared

      \K2         Online command mode enabled, send no break to remote
                  modem

      \K3         Send break to remote modem immediately

      \K4         Online command mode enabled, send no break to remote
                  modem

      \K5         Send break with transmitted data

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

                                   DIAL

  Type:                 Immediate

  Format:               AT [cmds] D<#> [cmds]

  Description:          Dials telephone number according to any modifiers
                        included in the string

  Note:                 Any combination of modifiers can be used to
                        produce the desired dial functions in sequence.

       Modifier                             Function

           L            Re-dial last number

           P            Pulse dialing enabled

           R            Accepted but not acted upon

          S=n           Dial stored telephone number n (n=0-3)

           T            Tone dialing enabled

           W            Dialing resumed following dial tone detection

           !            Modem commanded to go off-hook for specified time
                        before returning on-hook.

           @            Wait 5 seconds for quiet answer

           &            Waits for prompt tone

           ,            Dialing paused for amount of time specified in S8
                        register

           ;            Modem returned to command state after dialing

           ^            Toggles Calling tone enabled/disabled, for
                        current call

                         FLASH DIAL MODIFIER TIME

  Type:                Register

  Format               AT [cmds] S29=n [cmds]

  Default:             0

  Range:               0-255

  Unit:                .01 second

  Description:         Time the modem will go on-hook upon receiving the
                       ! dial modifier in dial string.

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] \Gn [cmds]

  Description:   Selects modem port flow control

    Command                              Function

      \G0        Flow control disabled

      \G1        Flow control enabled

                               FLOW CONTROL

  Type:          Register

  Format         AT [cmds] S39? [cmds]

  Description:   Displays the current flow control

     Value                               Meaning

       0         Flow control disabled

       3         RTS/CTS flow control enabled

       4         XON/XOFF flow control enabled

       5         Transparent XON/XOFF flow control enabled

       6         Both RTS/CTS and XON/XOFF flow control enabled

                       FLOW CONTROL CHARACTER - XOFF

  Type:          Register

  Format:        AT [cmds] S33=n [cmds]

  Default:       19

  Range:         0-255

  Unit:          ASCII

  Description:   Sets the character used to represent XOFF

                       FLOW CONTROL CHARACTER - XON

  Type:          Register

  Format:        AT [cmds] S32=n [cmds]

  Default:       17

  Range:         0-255

  Unit:          ASCII

  Description:   Sets the character used to represent XON

                             INACTIVITY TIMER

  Type:                   Register

  Format                  AT [cmds] S30=n [cmds]

  Default:                0

  Range:                  0-255

  Unit:                   10 seconds

  Description:            Maximum duration of DTE and DCE inactivity
                          allowed prior to initiating hang-up process.
                          S30=0 will disable timer.

                             LINE SIGNAL LEVEL

  Type:           Immediate

  Format:         AT [cmds] %L [cmds]

  Description:    Returns a value which indicates the received line
                  signal level

                            LINE SIGNAL QUALITY

  Type:          Immediate

  Format:        AT [cmds] %Q [cmds]

  Description:   Returns a value which indicates line signal quality

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports precomputed checksum

       I2        Reports OK

       I3        Reports firmware revision

       I4        Reports OEM defined identifier string

       I5        Reports country code

       I6        Reports data pump model and internal code revision

                               RPI/DTE SPEED

  Type:           Configuration

  Format:         AT [cmds] +Hn [cmds]

  Description:    Controls Rockwell Protocol Interface processing and DTE
                  speed

     Command                             Function

       +H0        RPI disabled

       +H1        RPI enabled and set DTE speed to 19.2Kbps

       +H2        RPI enabled and set DTE speed to 38.4Kbps

       +H3        RPI enabled and set DTE speed to 57.6Kbps

                                SLEEP TIMER

  Type:                   Register

  Format                  AT [cmds] S24=n [cmds]

  Default:                0

  Range:                  0-255

  Unit:                   1 second

  Description:            Maximum duration of DTE and DCE inactivity
                          allowed prior to initiating low-power sleep
                          mode. S24=0 will disable timer.

                         TRANSMISSION LEVEL - FAX

  Type:          Register

  Format:        AT [cmds] S92=n [cmds]

  Default:       10

  Range:         0-15

  Unit:          -1 dBm

  Description:   Sets the signal level for transmission while in fax mode

                         TRANSMISSION LEVEL - PSTN

  Type             Register or Configuration

  Format           AT [cmds] S91=n [cmds]

  Default          10

  Range            10-15

  Unit             -1 dBm

  Description      Sets the signal level for transmission over switched
                   phone lines

