
ACTIONTEC ELECTRONICS, INC.

FME288

Card Type                    Fax, Modem (synchronous/asynchronous),
                             Network Interface Card
Chip Set                     Unidentified
I/O Options                  Ethernet 10BaseT connector
NIC Type                     Ethernet
Network Transfer Rate        10Mbps
Maximum Modem Rate           28.8Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     PCMCIA Type II
Fax Class                    Class I & II
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.25bis,
                             V.32, V.32bis, V.34
Fax Modulation Protocol      ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, MNP10, V.42, V.42bis
Topology                     Star
Wiring Type                  Unshielded twisted pair
Boot ROM                     Not available

                                                                      V2286

                         Proprietary AT Command Set

                 AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

  Type:          Configuration

  Format:        AT [cmds] %En [cmds]

  Description:   Controls auto-retrain mode and fallback/fall-forward

    Command                              Function

      %E0        Auto-retrain disabled

      %E1        Auto-retrain enabled

      %E2        Auto-fallback/fall-forward enabled

      BIT MAPPED REGISTERS

    Register        Default

      S28        Unidentified

                          BIT-MAPPED REGISTER S14

  Format:             AT [cmds] S14=n [cmds]

  Default:            138

  Range:              0-174

  Unit:               Bit-mapped

  Description:        Controls echo, result codes and display, dial mode,
                      and answer/originate mode.

   Bit       Value                         Function

    0             0   Not used

    1              0  Command echo disabled

                  1   Command echo enabled

    2              0  Result codes enabled

                  1   Result codes disabled

    3              0  Display result codes in numeric format

                  1   Display result codes in verbose format

    4             0   Not used

    5              0  Tone dial enabled

                  1   Pulse dial enabled

    6             0   Not used

    7              0  Answer mode enabled

                  1   Originate mode enabled

                          BIT-MAPPED REGISTER S21

  Format                 AT [cmds] S21=n [cmds]

  Default:               4

  Range:                 0-253

  Unit:                  Bit-mapped

  Description:           Selects jack type, CTS/DCD/DSR signals, low DTR
                         action, and the long space disconnect function

    Bit       Value                          Function

     0               0   Selects RJ-11, RJ-41S, or RJ45S jack

                    1    Selects RJ-12 or RJ-13 jack

     1              0    Not used

     2               0   CTS forced high

                    1    CTS follows RTS

   4, 3             00   DTR signal ignored

                    01   Modem goes to command mode on low DTR

                    10   Modem disconnects on low DTR; Auto-Answer is
                         disabled
                   11
                         Modem is initialized on low DTR

     5               0   DCD forced high

                    1    DCD normal

     6               0   DSR forced high

                    1    DSR normal

     7               0   Long space disconnect function disabled

                    1    Long space disconnect function enabled

                          BIT-MAPPED REGISTER S22

  Format            AT [cmds] S22=n [cmds]

  Default:          117

  Range:            0-127

  Unit:             Bit-mapped

  Description:      Controls speaker volume and controls, and limits
                    results codes.

   Bit     Value                          Function

  1, 0         00   Volume off

               01   Low level volume

               10   Medium level volume

              11    High level volume

  3, 2         00   Speaker off

               01   Speaker off on carrier

               10   Speaker always on

              11    Speaker on during handshake

  6 - 4       000   Basic result codes only enabled

              100   Basic and connection speed result codes enabled

              101   Basic and connection speed result codes and dialtone
                    detection enabled
              110
                    All result codes except dialtone detection enabled
             111
                    All result codes enabled

                          BIT-MAPPED REGISTER S23

  Format                AT [cmds] S23=n [cmds]

  Default:              55

  Range:                0-189

  Unit:                 Bit-mapped

  Description:          Grants/denies remote digital loopback, controls
                        DTE rate and parity, and sets guard tone

    Bit       Value                         Function

     0              0   Remote digital loopback denied

                   1    Remote digital loopback allowed

   3 - 1          000   Sets serial port speed to 0-300bps

                  001   Sets serial port speed to 600bps

                  010   Sets serial port speed to 1200bps

                  011   Sets serial port speed to 2400bps

                  100   Sets serial port speed to 4800bps

                  101   Sets serial port speed to 9600bps

                 110    Sets serial port speed to 19200bps

   5, 4            00   Parity even

                   01   Not used

                   10   Parity odd

                  11    No parity

   7, 6            00   Guard tone disabled

                   01   Guard tone disabled

                  10    Guard tone 1800Hz enabled

                          BIT-MAPPED REGISTER S27

  Format               AT [cmds] S27=n [cmds]

  Default:             74

  Range:               0-111

  Unit:                Bit-mapped

  Description:         Selects synchronous/asynchronous mode, line type,
                       clock source, and ITU-T/Bell modes.

   Bit       Value                          Function

  3, 1,          000   Asynchronous mode, serial port speed follows
    0                  connect speed
                 001
                       Asynchronous off-line command mode and synchronous
                 010   connect mode

                 011   Asynchronous off-line command mode; modem
                       auto-dials first number in directory, then
                 100   synchronous connect mode

                 101   Asynchronous off-line command mode on low DTR,
                       synchronous connect mode on high DTR
                111
                       Auto-synchronous mode

                       Error correction mode

                       Buffered asynchronous mode

    2              0   Switched line

                  1    Leased line

  5, 4            00   Local modem generates transmit clock source

                  01   Local DTE generates transmit clock source

                 10    Remote DCE/DTE generates transmit clock source

    6              0   ITU/T mode

                  1    Bell mode

                          BIT-MAPPED REGISTER S31

  Format:                    AT [cmds] S31=n [cmds]

  Default:                   2

  Range:                     0-2

  Description:               Select automode

        Bit           Value                     Function

         0                  0   Not used

         1                   0  Auto-mode detection disabled

                            1   In originate mode, handshake begins at
                                line speed designated by the S37
                                register. Modem can shift to a slower
                                speed if necessary.

                                In answer mode, handshake attempted with
                                the following protocols in order -
                                V.32bis, V.32, V.22bis, V.22 or Bell 212,
                                V.21, and Bell 103

                          BIT-MAPPED REGISTER S40

  Format                AT [cmds] S40=n [cmds]

  Default:              105

  Range:                0-255

  Unit:                 Bit-mapped

  Description:          Controls MNP extended services, fallback, power
                        level, break handling, and block size.

    Bit       Value                         Function

     0              0   MNP extended services disabled

                   1    MNP extended services enabled

     1              0   MNP10 at 2400 and 1200bps disabled

                   1    MNP10 at 2400 and 1200bps enabled

     2              0   Power level adjustment enabled

                   1    Power level adjustment disabled

  5, 4, 3         000   \K0

                  001   \K1

                  010   \K2

                  011   \K3

                  100   \K4

                 101    \K5

   7, 6            00   MNP block size is 64 characters

                   01   MNP block size is 128 characters

                   10   MNP block size is 192 characters

                  11    MNP block size is 256 characters

                          BIT-MAPPED REGISTER S41

  Format           AT [cmds] S41=n [cmds]

  Default:         Unidentified

  Range:           0-31

  Unit:            Bit-mapped

  Description:     Selects compression, auto-retrain, flow control, and
                   MNP mode.

   Bit    Value                           Function

  1 - 0       00   Data compression disabled

              01   MNP5 enabled

              10   V.42bis enabled

             11    MNP5 and V.42bis enabled

  6, 2        00   Auto-retrain disabled

              01   Auto-retrain enabled

             10    Auto-retrain and auto-fallback enabled

    3          0   Flow control disabled

              1    Flow control enabled

    4          0   Stream mode for MNP

              1    Block mode for MNP

                         BIT-MAPPED REGISTER S201

  Format:              AT [cmds] S201=n [cmds]

  Default:             32

  Range:               0-62

  Description:         Controls power level and compromise equalizer

     Bit         Value                        Function

    4 - 0           00000  Initial power level -26dBm

                    00001  Initial power level -30dBm

                    00010  Initial power level -10dBm

                      ...  ...

                    01010  Initial power level -10dBm

                    01011  Initial power level -11dBm

                 ...to...  ...to...

                   11110   Initial power level -30dBm

       5                0   Equalizer disabled

                       1    Equalizer enabled

                                BREAK SEND

  Type:          Configuration

  Format:        AT [cmds] \Bn [cmds]

  Default:       3

  Range:         1-9

  Unit:          .1 second

  Description:   Sends break to modem

                                BREAK TYPE

  Type:                    Configuration

  Format:                  AT [cmds] \Kn [cmds]

  Description:             Configures action of break signal

     Command       Break from DTE     Modem receives      Break received
                                            \B          from remote modem

       \K0        Online command     Break sent to      Buffers cleared,
                  mode enabled,      remote modem and   break sent to DTE
                  send no break      buffers cleared
                  to remote modem

       \K1        Break sent to      Break sent to      Buffers cleared,
                  remote modem       remote modem and   break sent to DTE
                  and buffers        buffers cleared
                  cleared

       \K2        Online command     Send break to      Break sent
                  mode enabled,      remote modem       immediately to
                  send no break      immediately        DTE
                  to remote modem

       \K3        Send break to      Send break to      Break sent
                  remote modem       remote modem       immediately to
                  immediately        immediately        DTE

       \K4        Online command     Send break with    Break sent with
                  mode enabled,      transmitted data   received data to
                  send no break                         the DTE
                  to remote modem

       \K5        Send break with    Send break with    Break sent with
                  transmitted        transmitted data   received data to
                  data                                  the DTE

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] %Cn [cmds]

  Description:   Selects data compression

    Command                              Function

      %C0        Data compression disabled

      %C1        MNP5 enabled

      %C2        V.42bis enabled

      %C3        MNP5 and V.42bis enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        Reliable mode enabled

      \N3        Auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

      \N5        MNP reliable mode enabled

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Modifier                             Function

           J             Link will be negotiated at highest possible
                         speed

           K             Power level adjustment enabled

           L             Re-dial last number

           P             Pulse dialing enabled

           R             Accepted, but not acted upon

          S=n            Dial stored telephone number n

           T             Tone dialing enabled

           W             Dialing resumed following dial tone detection

           !             Modem commanded to go off-hook for specified
                         time before returning on-hook

           @             Wait for quiet answer

           ,             Dialing paused for amount of time specified in
                         S8 register

           ;             Modem returned to command state after dialing

           ^             Calling tone disabled

           >             Generate a grounding pulse on ground output

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] \Gn [cmds]

  Description:   Selects modem port flow control

    Command                              Function

      \G0        Flow control disabled

      \G1        Flow control enabled

                               FLOW CONTROL

  Type:          Read-only Register

  Format         AT [cmds] S39? [cmds]

  Description:   Displays the current flow control

     Value                               Meaning

       0         Flow control disabled

       3         RTS/CTS flow control enabled

       4         XON/XOFF flow control enabled

       5         Transparent XON/XOFF flow control enabled

       6         Both XON/XOFF and RTS/CTS flow control enabled

                       FLOW CONTROL CHARACTER - XOFF

  Type:          Register

  Format:        AT [cmds] S33=n [cmds]

  Default:       19

  Range:         0-255

  Unit:          ASCII

  Description:   Sets the character used to represent XOFF

                       FLOW CONTROL CHARACTER - XON

  Type:          Register

  Format:        AT [cmds] S32=n [cmds]

  Default:       17

  Range:         0-255

  Unit:          ASCII

  Description:   Sets the character used to represent XON

                             LOCK SERIAL PORT

  Type:          Configuration

  Format:        AT [cmds] \Jn [cmds]

  Description:   Sets operation of serial port speed

    Command                              Function

      \J0        Serial speed locked

      \J1        Serial speed follows connect speed

                    MAXIMUM BLOCK SIZE FOR TRANSMISSION

  Type:          Configuration

  Format:        AT [cmds] \An [cmds]

  Description:   Sets the maximum transmittable block size

    Command                              Function

      \A0        MNP block size is 64 characters

      \A1        MNP block size is 128 characters

      \A2        MNP block size is 192 characters

      \A3        MNP block size is 256 characters

                             LINE SIGNAL LEVEL

  Type:           Immediate

  Format:         AT [cmds] %L [cmds]

  Default:        Unidentified

  Range:          9-43

  Unit:           -1 dBm

  Description:    Returns a value which indicates the received line
                  signal level

                            LINE SIGNAL QUALITY

  Type:          Immediate

  Format:        AT [cmds] %Q [cmds]

  Description:   Returns a value which indicates line signal quality

                          MNP - EXTENDED SERVICES

  Type:          Configuration

  Format:        AT [cmds] -Kn [cmds]

  Description:   Selects MNP extended services

    Command                              Function

      -K0        MNP extended services disabled

      -K1        MNP extended services enabled

                          MNP - STREAM/BLOCK MODE

  Type:          Configuration

  Format:        AT [cmds] \Ln [cmds]

  Description:   Selects the transfer mode for MNP link

    Command                              Function

      \L0        Stream mode for MNP enabled

      \L1        Block mode for MNP enabled

                             MNP10 - FALLBACK

  Type:          Configuration

  Format:        AT [cmds] -Qn [cmds]

  Description:   Allows MNP10 to fall back to speeds slower than 4800bps

    Command                              Function

      -Q0        MNP10 at 2400 and 1200bps disabled

      -Q1        MNP10 at 2400 and 1200bps enabled

                         MNP10 - LINK NEGOTIATION

  Type:          Configuration

  Format:        AT [cmds] *Hn [cmds]

  Description:   Sets the speed at which MNP10 link negotiation will
                 occur

    Command                              Function

      *H0        Link will be negotiated at highest possible speed

      *H1        Link will be negotiated at 1200bps

      *H2        Link will be negotiated at 4800bps

                        MNP10 - POWER LEVEL ADJUST

  Type:                Configuration

  Format:              AT [cmds] )Mn [cmds]

  Description:         Controls automatic transmit power level adjustment
                       during MNP 10 link negotiation

       Command                              Function

         )M0           Power level adjustment disabled

         )M1           Power level adjustment enabled

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports OK

       I6        Reports modem data pump model and internal code revision

                                TEST MODES

  Type:              Register

  Format:            AT [cmds] S16=n [cmds]

  Default:           0

  Range:             0-125

  Unit:              Bit-mapped

  Description:       Controls loopback tests: analog, digital, remote
                     digital, and self tests

   Bit      Value                          Function

    0            0   Local analog loopback not in progress

                1    Local analog loopback in progress

    1           0    Not used

    2            0   Local digital loopback not in progress

                1    Local digital loopback in progress

    3            0   Modem not in remote digital loopback

                1    Remote digital loopback in progress

    4            0   Remote digital loopback not requested

                1    Remote digital loopback requested

    5            0   Remote digital loopback w/ self-test not in progress

                1    Remote digital loopback w/ self-test in progress

    6            0   Local analog loopback w/ self-test not in progress

                1    Local analog loopback w/ self-test in progress

                              TEST MODE - PTT

  Type:          Immediate

  Format:        AT [cmds] %TTn [cmds]

  Description:   Send PTT test signals for a line tests

                         TRANSMISSION LEVEL - FAX

  Type:          Register

  Format:        AT [cmds] S92=n [cmds]

  Default:       10

  Range:         0-15

  Unit:          -1 dBm

  Description:   Sets the signal level for transmission while in fax mode

                     TRANSMISSION LEVEL - LEASED-LINE

  Type:          Register

  Format:        AT [cmds] S99=n [cmds]

  Default:       10

  Range:         0-15

  Unit:          -1 dBm

  Description:   Sets the signal level for transmission over leased-lines

                        TRANSMISSION LEVEL - PSTN

  Type          Register

  Format        AT [cmds] S91=n [cmds]

  Default       10

  Range         0-15

  Unit          -1 dBm

  Description   Sets the signal level for transmission over PSTN

                            V.25bis COMMAND SET

                          CONNECT INCOMING CALLS

  Type:                   Immediate

  Format:                 CIC

  Description:            Instructs the modem to answer an incoming call;
                          if no call is currently incoming, a result of
                          INV will be returned.

                 CALL REQUESTED NUMBER AND IDENTIFICATION

  Type:          Immediate

  Format:        CRI<#>

  Description:   Adds dial string and identifier into memory.

                           CALL REQUESTED NUMBER

  Type:                   Immediate

  Format:                 CRN<#>

  Description:            Dials the number given; it will ignore spaces
                          and hyphens in the string; if the string is
                          more than fifty characters long, a result of
                          INV will be returned.

                         CALL REQUEST WITH ADDRESS

  Type:          Immediate

  Format:        CRSn

  Description:   Dials the number stored in memory register n

                          DISREGARD INCOMING CALL

  Type:                  Immediate

  Format:                DIC

  Description:           Instructs the modem to ignore the incoming call,
                         if the modem is set to automatically answer; if
                         no call is currently incoming, a result of INV
                         will be returned.

                              PROGRAM NUMBER

  Type:                  Configuration

  Format:                PRNn or PRN

  Description:           Stores a phone number in memory address n. If
                         the second form of this command is issued (i.e.
                         with no string to store), it will clear memory
                         address n.

                      REQUEST LIST OF DELAYED NUMBERS

  Type:                   Immediate

  Format:                 RLD

  Description:            Requests the list of delayed numbers from the
                          modem; this is a list of numbers that the modem
                          attempted to call and failed, and is not
                          allowed to call again until a set amount of
                          time has elapsed; this is usually to prevent
                          repeated dialing of a number (which could
                          indicate an attempted security breach).

                     REQUEST LIST OF FORBIDDEN NUMBERS

  Type:                   Immediate

  Format:                 RLF

  Description:            Requests the list of forbidden numbers from the
                          modem; the modem is unable to dial numbers on
                          this list until its power has been cycled.

                          REQUEST LISTED NUMBERS

  Type:          Immediate

  Format:        RLI

  Description:   The modem will return VAL message.

                      V.25BIS COMMAND SET RESULT CODES

                          CALL FAILURE INDICATOR

  Type:                     Response

  Format:                   CFIxx

  Description:              Indicates that the attempt to connect failed

      Response            Name                    Description

       CFIAB             Abort        The call was aborted because either
                                      no dialtone was detected or a
                                      character was received from the
                                      host computer.

       CFICB            DCE Busy      An incoming call was detected after
                                      the dialing command was issued.

       CFIET          Engaged Tone    A busy signal was detected.

       CFIFC            Forbidden     The number given is on the
                          Call        forbidden list.

       CFINS           Not Stored     The memory address given did not
                                      contain a valid telephone number.

       CFINT            No Tone       The remote party did not issue a
                                      response tone.

       CFIRT           Ring Tone      A responding tone was detected, but
                                      the call timed out before it was
                                      completed.

                                CONNECTION

  Type:          Response

  Format:        CNX

  Description:   A connection has been successfully established

                               DELAYED CALL

  Type:                   Response

  Format:                 DLCn

  Description:            The telephone number given is on the delayed
                          call list; the call cannot be completed until n
                          minutes elapse.

                               INCOMING CALL

  Type:          Response

  Format:        INC

  Description:   An incoming call has been detected

                                  INVALID

  Type:          Response

  Format:        INV

  Description:   The modem was issued an improper command

                                   VALID

  Type:          Response

  Format:        VAL

  Description:   The command issued is valid and is being executed

