
CARDINAL TECHNOLOGIES, INC

9600BPS V.32 V.42BIS FAX (1/2CARD-VER.1)

Card Type                    Modem (asynchronous)
Chip Set                     Unidentified
Maximum Data Rate            9600bps
Maximum Fax Rate             Unidentified
Data Bus                     8-bit ISA
Fax Class                    Class I & II
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.21, V.22, V.22bis, V.32
Fax Modulation Protocol      Unidentified
Error Correction/Compression MNP5, V.42, V.42bis

[Image]

                                CONNECTIONS

         Function            Label            Function             Label

  Line out/in                    CN1       Line in/out              CN2

            SERIAL PORT ADDRESS

    Setting        SW1/1          SW1/2

  COM1 (3F8h)       Off            Off

  COM2 (2F8h)       Off            On

  COM3 (3E8h)        On            Off

  COM4 (2E8h)        On            On

      INTERRUPT SELECTION

  Setting    SW1/3      SW1/4

     2         On        On

     3        Off        On

     4        Off        Off

     5         On        Off

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, Comma, A/

  A, B, C, E, F, H, L, M, N, O, P, Q, S, T, V, W, X, Y, Z

  &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &U, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \C, \G, \J, \O, \U, \V, \X, \Y, \Z

  %A, %E, %G

                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S25

  S26, S27, S30, S37, S95, S108, S109, S110

                             Special Commands

  "H, "O, -C, -J, -V

  Note: Please see MHI Help file for full command documentation.

                         Proprietary AT Command Set

                          BIT-MAPPED REGISTER S23

  Format                AT [cmds] S23=n [cmds]

  Default:              15

  Range:                0-191

  Unit:                 Bit-mapped

  Description:          Grants/denies remote digital loopback, controls
                        DTE rate and parity, and sets guard tone.

    Bit       Value                         Function

     0              0   Remote digital loopback denied

                   1    Remote digital loopback allowed

   3 - 1          000   Sets serial port speed to 0-300bps

                  001   Sets serial port speed to 1200bps

                  010   Sets serial port speed to 2400bps

                  011   Sets serial port speed to 4800bps

                  100   Sets serial port speed to 7200bps

                  101   Sets serial port speed to 9600bps or 14400bps

                  110   Sets serial port speed to 19200bps

                 111    Sets serial port speed to 38400bps or 57600bps

   5, 4            00   Parity even

                   01   Space or No parity

                   10   Parity odd

                  11    Mark Parity

   7, 6            00   Guard tone disabled

                   01   Guard tone 550Hz enabled

                  10    Guard tone 1800Hz enabled

                                BREAK TYPE

  Type:                Configuration

  Format:              AT [cmds] \Kn [cmds]

  Description:         Configures action of break signal

   Command       Break from        Modem       Break from        Break
                   DTE in       receives \B      DTE in        received
                 RELIABLE or      during      DIRECT mode     from remote
                NORMAL mode       command                       modem
                                  state

     \K0        Online         Break sent     Online         Buffers
                command mode   to remote      command mode   cleared,
                enabled,       modem and      enabled,       break sent
                send no        buffers        send break     to DTE
                break to       cleared        to remote
                remote modem                  modem

     \K1        Break sent     Break sent     Send break     Buffers
                to remote      to remote      to remote      cleared,
                modem and      modem and      modem          break sent
                buffers        buffers        immediately    to DTE
                cleared        cleared

     \K2        Online         Send break     Online         Break sent
                command mode   to remote      command mode   immediately
                enabled,       modem          enabled,       to DTE
                send no        immediately    send break
                break to                      to remote
                remote modem                  modem

     \K3        Send break     Send break     Send break     Break sent
                to remote      to remote      to remote      immediately
                modem          modem          modem          to DTE
                immediately    immediately    immediately

     \K4        Online         Send break     Online         Break sent
                command mode   with           command mode   with
                enabled,       transmitted    enabled,       received
                send no        data           send break     data to the
                break to                      to remote      DTE
                remote modem                  modem

     \K5        Send break     Send break     Send break     Break sent
                with           with           to remote      with
                transmitted    transmitted    modem          received
                data           data           immediately    data to the
                                                             DTE

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] %Cn [cmds]

  Description:   Selects data compression

    Command                              Function

      %C0        MNP5 disabled

      %C1        MNP5 enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        MNP reliable mode enabled

      \N3        V.42 auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

      \N5        LAPM/Normal mode enabled

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Modifier                             Function

           P             Pulse dialing enabled

           R             Answer mode enabled, originate mode disabled
                         following handshake initiation

          S=n            Dial stored telephone number n=0-3

           T             Tone dialing enabled

           W             Dialing resumed following dial tone detection

           ,             Dialing paused for amount of time specified in
                         S8 register

           !             Modem commanded to go off-hook for specified
                         time before returning on-hook

           @             Wait for quiet answer

           ;             Modem returned to command state after dialing

                             DTE CONNECT SPEED

  Type:          Configuration

  Format:        AT [cmds] S112=n [cmds]

  Description:   Select the DTE speed during data transfer

    Command                              Function

     S112=0       Last AT speed

     S112=1       Not used

     S112=2       Sets DTE speed to 300bps

     S112=3       Sets DTE speed to 1200bps

     S112=4       Sets DTE speed to 2400bps

     S112=5       Sets DTE speed to 4800bps

     S112=6       Sets DTE speed to 7200bps

     S112=7       Sets DTE speed to 9600bps

     S112=8       Sets DTE speed to 12000bps

     S112=9       Sets DTE speed to 14400bps

    S112=10       Sets DTE speed to 16800bps

    S112=11       Sets DTE speed to 19200bps

    S112=12       Sets DTE speed to 38400bps

    S112=13       Sets DTE speed to 57600bps

    S112=14       Sets DTE speed to 600bps

                             FLOW CONTROL TYPE

  Type:          Configuration

  Format:        AT [cmds] \Qn [cmds]

  Description:   Sets type of flow control used by modem

    Command                              Function

      \Q0        Flow control disabled

      \Q1        Bi-directional XON/XOFF flow control enabled

      \Q2        Unidirectional hardware flow control enabled

      \Q3        Bi-directional hardware flow control enabled (RTS/CTS)

                             INACTIVITY TIMER

  Type:                  Configuration

  Format:                AT [cmds] \Tn [cmds]

  Default:               0

  Range:                 0-90

  Unit:                  1 minute

  Description:           Sets the length of time that the modem does not
                         receive information before it disconnects.

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports ROM checksum

       I2        Tests and reports ROM checksum

       I3        Reports ROM components

       I4        Reports modem capabilities

