
TDK ELECTRONICS CORPORATION

DF2814 V.34 PC CARD DATA/FAX MODEM

Card Type                    Fax, Modem (asynchronous)
Chip Set                     Unidentified
Maximum Data Rate            28.8Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     PCMCIA Type II
Fax Class                    Class I
Data Modulation Protocol     Bell 103J/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34

                             Rockwell V.FC
Fax Modulation Protocol      ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, MNP10, V.42, V.42bis

                                                                      V2309

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, A/

  A, B, D, E, H, I, L, M, O, P, Q, S, T, V, W, X, Y, Z

  &C, &D, &F, &G, &P, &S, &T, &W, &Y, &Z

                           Extended AT Commands

  %A, %C, %F, %G, \A, \B, \C, \E, \G, \J, \K, \N, \Q, \T, \V, \X

                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S25,
  S26

                             Special Commands

  -K, -Q, )M, *H, :E, @M

  Note: See MHI Help file for full command documentation.

  BIT MAPPED S-REGISTERS

  Register      Default

     S14          170

     S21           48

     S22          118

     S23           31

     S27           64

    BIT MAPPED :T-REGISTERS

    Register        Default

      :T15            128

      :T19             1

      :T23       Unidentified

      :T26             0

                         PROPRIETARY AT% COMMANDS

    Command                    Description                     Default

       %B                  Modem port data rate                %B28800

       %D                Disconnect buffer delay                 %D0

       %I           Edit connection security password        Unidentified

       %L                     Speed matching                     %L1

       %O                 V.23 equalizer control                 %O1

       %R                 Display all registers                 None

       %U                Clear serial port speed                 %U2

       %V             Display modem firmware version            None

       %W                  Pulse digit command                   %W0

               PROPRIETARY AT\ COMMANDS

  Command             Description            Default

     \D       Serial port DSR/CTS control      \D0

     \F       Display stored phone numbers     None

     \H         Hewlett Packard ENQ/ACK        \H0

     \P       Write a stored phone number      None

     \R       Serial port ring indicator       \R1

     \S         Display on-line status         None

             PROPRIETARY AT- COMMANDS

  Command           Description           Default

    -D              Repeat dial             None

    -M       MNP class connect message      -M0

    -O          Serial port parity          -O4

    -P             Check parity             -P0

                       PROPRIETARY AT$ COMMANDS

    Command                  Description                   Default

      $A                Auto-answer auto-logon               $A0

      $B                Serial port data rate              $B38400

      $D                 Power-up diagnostics                None

      $G                 Dial access security                $G0

      $H          Edit Dial access security database         None

      $I         Display Dial access security database       None

      $J                 Clear dial database                 None

      $L                    Logon sequence                   None

      $M         Verify connection security password         $M0

      $N          List connection security passwords         None

      $P              Database security password             None

      $V                   Logon view mode                   $V1

                    PROPRIETARY AT) COMMANDS

   Command                 Description                 Default

      )H        Auto-dial connection restore timer       )H0

      )Q          Serial port inactivity timer           )Q5

                        PROPRIETARY AT* COMMANDS

    Command                  Description                   Default

      *A                Request remote access                None

      *E                Enable remote access                 *E0

      *I           Remote access modem identifier            None

      *M             Modify remote access level              None

      *P               Remote access passwords               None

      *Q         Recover remote access configuration         None

      *R            Enable remote access security            *R0

      *S          Remote access attention character          *S42

      *U         Update remote access configuration          None

      *W            Store complete configuration             *W0

      *X                 Exit remote access                  None

             PROPRIETARY AT: COMMANDS

  Command          Description           Default

    :D             Manual dial             :D0

    :K        Kermit/UUCP protocol         :K0

    :Q        Kermit mark character        :Q1

    :U           DCD time delay            :U0

    :V           CTS time delay            :V0

    :X           DSR time delay            :X0

               PROPRIETARY AT@ COMMANDS

  Command            Description            Default

     @C       CTS/DSR/CD connect message      @C0

                  PROPRIETARY AT^ COMMANDS

   Command            Description              Default

     ^V       Display bootstrap revision         None

                        PROPRIETARY AT:T REGISTERS

     Command                  Description                   Default

       :T0             V.22/22bis/32 mode timer                40

       :T1            V.23 split-speed mode timer              30

       :T2                  V.21 mode timer                    0

       :T3             V.21/23 answer tone timer               3

       :T4          Line turnaround delay-carrier on           20
                                 timer

       :T5          V.23 intercharacter delay timer            7

       :T6              DCD turn on delay timer               200

       :T7             False answer abort timer                60

      :T14            Connect message delay timer              0

      :T16              CTS turn on delay timer                0

      :T17           V.32/32bis connection training            0
                                 timer

      :T22                     DSR timer                       34

      :T29               Parallel packet size                  16

