
TOSHIBA

T1100PLUS MODEM (VER.1)/T1200 MODEM/T3100 MODEM (VER.1)/T5100 MODEM/T5200
MODEM

Card Type                Modem (asynchronous)
Chip Set                 Unidentified
Maximum Data Rate        2400bps
Data Bus                 Internal/Toshiba bus
Data Modulation Protocol Bell 103/212A

                         ITU-T V.21, V.22, V.22bis

[Image]

                                CONNECTIONS

       Function           Label             Function              Label

  RS-232-C                    CN1       Line in                    CN3

  Line out                    CN2       Proprietary connection     CN4
                                        to computer

                                   POWER

                 Setting                                 SW1

     Auto-start with telecommunication               Position 1
                 software

    Serial port in use/modem disabled                Position 2

                    On                               Position 3

                               PORT ADDRESS

          Modem                  Serial Port                 SW6

       COM1 (3F8h)               COM2 (2F8h)                  Up

       COM2 (2F8h)               COM1 (3F8h)                 Down

            Only T3100 and T5100 has SW6, T1100PLUS and T1200 are
            defaulted to COM2, T1600 uses software to determine the COM
            setting, T5200 uses the SETUP program to set the COM port.

            When SW1 is set to position 2 (serial port in use), serial
            port address is used.

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, +++, Comma, Semicolon, A/

  A, B, C, E, F, H, I, L, M, O, P, Q, S, T, V, X, Y, Z

  &C, &D, &F, &G, &P, &T, &W, &Y, &Z

                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S25

  Note: See MHI Help file for full command documentation.

                         Proprietary AT Command Set

                          BIT-MAPPED REGISTER S23

  Format            AT [cmds] S23=n [cmds]

  Default:          Unidentified

  Range:            0-55

  Unit:             Bit-mapped

  Description:      Grants/denies remote digital loopback, controls DTE
                    rate and parity.

   Bit     Value                          Function

    0           0   Remote digital loopback denied

               1    Remote digital loopback allowed

  2, 1         00   Sets serial port speed to 0-300bps

               01   Not used

               10   Sets serial port speed to 1200bps

              11    Sets serial port speed to 2400bps

    3          0    Not used

  5, 4         00   Parity even

               01   Space Parity

               10   Parity odd

              11    Mark or No Parity

                          BIT-MAPPED REGISTER S27

  Format           AT [cmds] S27=n [cmds]

  Default:         Unidentified

  Range:           0-116

  Unit:            Bit-mapped

  Description:     Selects ITU-T/Bell modes.

   Bit    Value                           Function

  1, 0       00    Not used

    2         0    Not used

    3         0    Not used

  5, 4       00    Not used

    6          0   ITU/T mode

              1    Bell mode

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DP             Pulse dialing enabled

          DR             Answer mode enabled; originate mode disabled
                         following handshake initiation.

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

           /             Pause for .125 second

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

