
ANGIA COMMUNICATIONS, INC.

PCMCIA 14400BPS DATA/14400BPS FAX

Card Type                    Fax, Modem (asynchronous)
Chip Set                     Unidentified
Maximum Data Rate            14.4Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     PCMCIA Type II
Fax Class                    Class I
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis
Fax Modulation Protocol      ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis

                                                                      V2329

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, +++, Comma, A/

  A, B, C, D, E, F, H, L, M, O, P, Q, S, T, V, W, X, Y, Z

  &C, &D, &E, &G, &J, &L, &M, &P, &Q, &R, &T, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \C, \G, \J, \K, \N \Q, \V, \X, \Z, %A, %E

                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S11, S12, S16, S18, S25, S26,
  S36

  S38, S39, S46, S48

  Note: See MHI Help file for full command documentation.

                         Proprietary AT Command Set

   BIT MAPPED REGISTERS

  Register     Default

     S14      Read-only

     S19          26

     S20          32

     S21      Read-only

     S22      Read-only

     S23      Read-only

     S27      Read-only

                                COMPRESSION

  Type:           Configuration

  Format:         AT [cmds] %Cn [cmds]

  Description:    Selects data compression

     Command                             Function

       %C0        Data compression disabled

       %C1        Data compression enabled; V.42bis during LAPM, MNP5
                  during MNP

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Direct mode enabled

      \N1        Normal mode enabled

      \N2        MNP reliable mode enabled

      \N3        MNP auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

      \N5        V.42 auto-reliable mode enabled

      \N6        Reliable mode enabled

      \N7        Auto-reliable mode enabled

                         DISPLAY FIRMWARE VERSION

  Type:          Immediate

  Format:        AT [cmds] %V [cmds]

  Description:   Displays firmware version information

                                  ENQ/ACK

  Type:          Configuration

  Format:        AT [cmds] \Hn [cmds]

  Description:   Controls Hewlett Packard ENQ/ACK protocol

    Command                              Function

      \H0         Hewlett Packard ENQ/ACK disabled

      \H1         Hewlett Packard ENQ/ACK emulating terminal enabled

      \H2         Hewlett Packard ENQ/ACK emulating host

                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] &F [cmds]

  Description:      Sets values in active profile to values found in the
                    default profile

      Command                             Function

        &F0         Restore auto-reliable compression/correction default
                    profile

        &F1         Restore auto-reliable compression/correction default
                    profile

                             INACTIVITY TIMER

  Type:                  Configuration

  Format:                AT [cmds] \Tn [cmds]

  Default:               0

  Range:                 0-90

  Unit:                  1 minute

  Description:           Sets the length of time that the modem does not
                         receive information before it disconnects.

                          MINIMUM MODEM PORT RATE

  Type:          Configuration

  Format:        AT [cmds] %Mn [cmds]

  Description:   Selects the minimum modem port rate

    Command                              Function

     %M300        300bps selected

     %M1200       1200bps selected

     %M2400       2400bps selected

     %M4800       4800bps selected

     %M7200       7200bps selected

     %M9600       9600bps selected

    %M12000       12000bps selected

    %M14400       14400bps selected

                              MODEM PORT RATE

  Type:          Configuration

  Format:        AT [cmds] %Bn [cmds]

  Description:   Selects the modem port rate

    Command                              Function

     %B300        300bps selected

     %B1200       1200bps selected

     %B2400       2400bps selected

     %B4800       4800bps selected

     %B7200       7200bps selected

     %B9600       9600bps selected

    %B12000       12000bps selected

    %B14400       14400bps selected

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports ROM checksum

       I2        Reports OK

       I3        Reports a date code

