
BROOKTROUT TECHNOLOGY, INC.

TR114-I4C, TR114-I4D, TR114-I4L (REV. 5)

Card Type              Telephony
Processor              NS32FX16/NS32FX164
Processor Speed        25MHz
Maximum Onboard Memory 1MB DRAM
I/O Options            Line out (4)
Data Bus               8/16-bit ISA
Line Type              DID, Loop-start

[Image]

                                CONNECTIONS

           Function             Label           Function           Label

  Loop-start daughterboard       J3      Lines 1 and 2              PJ1
  header

  Loop-start daughterboard       J4      Lines 3 and 4              PJ2
  header

  DID daughterboard header       J5      Loop-start chip            U1

  48V DC power in                J8

                        USER CONFIGURABLE SETTINGS

                  Setting                       Label        Position

     Internal self-test disabled               SW1/1           Off

      Internal self-test enabled                SW1/1           On

     Interrupt pull-up resistor enabled        SW1/2           On

      Interrupt pull-up resistor disabled       SW1/2           Off

            Note:SW1/2 should be on for only one TR112 or TR114 per
            system.

                                  INTERRUPT

    Setting       J1       J2/A     J2/B     J2/C    J2/D     J2/E     J2/F

      IR/FONT>   Open      Open     Open     Open    Open     Open     Closed

       IRQ3      Open     Closed    Open     Open    Open     Open     Open

       IRQ4      Open      Open    Closed    Open    Open     Open     Open

      IRQ5      Open      Open     Open    Closed   Open     Open     Open

       IRQ6      Open      Open     Open     Open    Closed   Open     Open

       IRQ7      Open      Open     Open     Open    Open     Closed   Open

       IRQ10     Pins 9    Open     Open     Open    Open     Open     Open
                  & 10
                closed

       IRQ11     Pins 7    Open     Open     Open    Open     Open     Open
                  & 8
                closed

       IRQ12     Pins 5    Open     Open     Open    Open     Open     Open
                  & 6
                closed

       IRQ14     Pins 3    Open     Open     Open    Open     Open     Open
                  & 4
                closed

       IRQ15     Pins 1    Open     Open     Open    Open     Open     Open
                  & 2
                closed

                             BASE I/O ADDRESS

   Setting      SW1/3     SW1/4     SW1/5     SW1/6     SW1/7      SW1/8

       000h      On        On        On         On        On        On

       010h      Off       On        On         On        On        On

       020h      On        Off       On         On        On        On

       030h      Off       Off       On         On        On        On

       040h      On        On        Off        On        On        On

      260h      On        Off       Off        On        On        Off

       3B0h      Off       Off       On        Off       Off        Off

       3C0h      On        On        Off       Off       Off        Off

       3D0h      Off       On        Off       Off       Off        Off

       3E0h      On        Off       Off       Off       Off        Off

       3F0h      Off       Off       Off       Off       Off        Off

            Note: A total of 64 base address settings are available. The
            switches are a binary representation of the decimal memory
            addresses. SW1/8 is the Most Significant Bit and switch SW1/3
            is the Least Significant Bit. The switches have the following
            decimal values: SW1/8=512, SW1/7=256, SW1/6=128, SW1/5=64,
            SW1/4=32, SW1/3=16. Turn off the switches and add the values
            of the switches that are off to obtain the correct memory
            address. (Off=1, On=0)

                            DIAGNOSTIC LED(S)

     LED        Color       Status                  Function

    LED1         Red          N/A                    Line 1

    LED2         Red          N/A                    Line 2

    LED3         Red          N/A                    Line 3

    LED4         Red          N/A                    Line 4

            Note:The functions of the LEDs depend on firmware settings.

