
MOTOROLA, INC.

VANGUARD 305

Card Type              Frame relay adapter, Token Ring router
Processor              Motorola 68360
Processor Speed        Unidentified
Chip Set               Unidentified
Maximum Onboard Memory 8MB DRAM/2MB Flash RAM
I/O Options            Serial ports (3)
Network Transfer Rate  4Mbps/16Mbps
DSU Transfer Rate      56Kbps
ISDN Transfer Rate     64Kbps x 2
DSU Protocol           DDS
ISDN Protocol          Unidentified
Switch Type            Unidentified
Data Bus               External
Topology               Linear Bus/Star
Wiring Type            Unshielded twisted pair

                       Shielded twisted pair
Boot ROM               Not available

[Image]

                                CONNECTIONS

         Function             Label           Function            Label

  Reset button                 BT1      CTP connector or ISDN      CN4
                                        connector (port 4)

  Lamp test button             BT2      V.24 serial port           CN5
                                        (port 3)

  Header for daughtercard      CN1      V.11, V.24, V.35, or       CN6
                                        V.36 serial port
                                        (port 2)

  Unshielded twisted pair      CN2      120VAC power               CN7
  connector

  Shielded twisted pair        CN3      Power switch               SW3
  connector

            Note:When LED4 is on, press the lamp test button to reset it.

            Port 1 is the daughterboard.

                        USER CONFIGURABLE SETTINGS

                    Setting                        Label       Position

          Port 2 pin 22 used for ring             SW1/1         Off
           indicator

           Port 2 pin 22 used to enter test        SW1/1          On
           mode in DCE mode, ring indicator in
           DTE mode

          Port 2 pin 25 used for test mode        SW1/2         Off
           indicator

           Port 2 pin 25 used for test mode        SW1/2          On
           indicator for DCE mode, busy out
           for DTE mode

          Port 3 pin 22 used for ring             SW1/3         Off
           indicator

           Port 3 pin 22 used to enter test        SW1/3          On
           mode in DCE mode, ring indicator in
           DTE mode

          Port 3 is normal serial port            SW1/4         Off

           Port 3 is the PAD port (forces          SW1/4          On
           serial configuration to 9600bps, no
           parity, 8 data bits, 1 stop bit)

          Factory configured - do not alter       SW1/5         Off

          Normal operation                        SW1/6         Off

           Reset entire configuration to           SW1/6          On
           factory defaults

            Note:To use SW1/6, power up the adapter, turn SW1/6 on, press
            the reset button, and turn SW1/6 back off again.

                    DRAM

    Setting       On Board         S1

      4MB           4MB           None

      8MB           4MB        (1) 4MB x 9

                                PORT 2 TYPE

  Setting     SW2/1      SW2/2     SW2/3     SW2/4      SW2/5     SW2/6

  V.11 DTE     Off        Off       Off       Off        Off        On

  V.11 DCE     Off        Off       Off       Off        Off        On

  V.24 DTE      On        On        On         On        On        Off

  V.24 DCE      On        On        On         On        On        Off

  V.35 DTE     Off        Off       Off       Off        Off        On

  V.35 DCE     Off        Off       Off       Off        Off        On

  V.36 DTE     Off        Off       Off       Off        Off        On

  V.36 DCE     Off        Off       Off       Off        Off        On

    DSU        Off        Off       Off       Off        Off        On

                            PORT 2 TYPE (CONT)

  Setting         SW2/7              SW2/8                  U1

  V.11 DTE          On                On          V.11 module in position
                                                             1

  V.11 DCE          On                On          V.11 module in position
                                                             2

  V.24 DTE         Off                Off         V.24 module in position
                                                             1

  V.24 DCE         Off                Off         V.24 module in position
                                                             2

  V.35 DTE          On                On          V.35 module in position
                                                             1

  V.35 DCE          On                On          V.35 module in position
                                                             2

  V.36 DTE          On                On          V.36 module in position
                                                             1

  V.36 DCE          On                On          V.36 module in position
                                                             2

    DSU             On                On           DSU module in position
                                                             1

                  DIAGNOSTIC LED(S) (RESET AND POWER-UP)

      LED1             LED3                      Condition

    Blinking            Off         Adapter is loading software into DRAM
                                               from flash RAM

       Off           Blinking         Adapter is performing self-test

       Off              Off        Adapter is initializing configuration

       On               Off                   Adapter is ready

       Off              On                    Self-test failed

            Note:On reset or power-up, the LEDs should go through, in
            order, the first four actions shown above. If the adapter
            proceeds immediately to the fourth action, the code in the
            firmware is invalid.

                             DIAGNOSTIC LED(S)

     LED         Color          Status                Condition

    LED1         Green            On             Software is running

    LED1         Green           Off             Software not running

    LED1         Green         Blinking       Software is downloading or
                                                   card is booting

    LED2         Green            On                 Power is on

    LED2         Green           Off                 Power is off

    LED3          Red             On                 Test failed

    LED3          Red            Off          No test in progress or test
                                                        passed

    LED3          Red          Blinking            Test in progress

    LED4          Red             On            Processor did not reset
                                                  timer in set time

    LED4          Red            Off               Normal operation

    LED5         Yellow           On           Card is transmitting MARK
                                                   signal to port 1

    LED5         Yellow          Off          Card is transmitting SPACE
                                                   signal to port 1

    LED6         Yellow           On            Card is receiving MARK
                                                  signal from port 1

    LED6         Yellow          Off            Card is receiving SPACE
                                                  signal from port 1

    LED7         Yellow           On           Card is transmitting MARK
                                                   signal to port 2

    LED7         Yellow          Off          Card is transmitting SPACE
                                                   signal to port 2

    LED8         Yellow           On            Card is receiving MARK
                                                  signal from port 2

    LED8         Yellow          Off            Card is receiving SPACE
                                                  signal from port 2

    LED9         Yellow           On           Card is transmitting MARK
                                                   signal to port 3

    LED9         Yellow          Off          Card is transmitting SPACE
                                                   signal to port 3

    LED10        Yellow           On            Card is receiving MARK
                                                  signal from port 3

    LED10        Yellow          Off            Card is receiving SPACE
                                                  signal from port 3

    LED11        Yellow           On           Card is transmitting MARK
                                                   signal to port 4

    LED11        Yellow          Off          Card is transmitting SPACE
                                                   signal to port 4

    LED12        Yellow           On            Card is receiving MARK
                                                  signal from port 4

    LED12        Yellow          Off            Card is receiving SPACE
                                                  signal from port 4

    LED13        Yellow           On           Card is transmitting MARK
                                                  signal to network

    LED13        Yellow          Off          Card is transmitting SPACE
                                                  signal to network

    LED14        Yellow           On            Card is receiving MARK
                                                 signal from network

    LED14        Yellow          Off            Card is receiving SPACE
                                                 signal from network

Card Type   Serial
I/O Options Serial port

[Image]

                                CONNECTIONS

        Function            Label            Function             Label

  V.11 V.24, V.35, V.36,     CN1       Header to main board       CN2B
  or DSU port                          (on both front and
                                       back of card)

                        USER CONFIGURABLE SETTINGS

                   Setting                      Label        Position

          Pin 22 used for ring indicator        P22         Pins 2 & 3
                                                              closed

           Pin 22 used to enter test mode        P22         Pins 1 & 2
           in DCE mode, ring indicator in                     closed
           DTE mode

          Pin 25 used for test mode             P25         Pins 1 & 2
           indicator                                          closed

           Pin 25 used for test mode             P25         Pins 2 & 3
           indicator for DCE mode, busy out                   closed
           for DTE mode

                             SERIAL PORT TYPE

  Setting     SW1/1      SW1/2     SW1/3     SW1/4      SW1/5     SW1/6

  V.11 DTE     Off        Off       Off       Off        Off        On

  V.11 DCE     Off        Off       Off       Off        Off        On

  V.24 DTE      On        On        On         On        On        Off

  V.24 DCE      On        On        On         On        On        Off

  V.35 DTE     Off        Off       Off       Off        Off        On

  V.35 DCE     Off        Off       Off       Off        Off        On

  V.36 DTE     Off        Off       Off       Off        Off        On

  V.36 DCE     Off        Off       Off       Off        Off        On

    DSU        Off        Off       Off       Off        Off        On

                         SERIAL PORT TYPE (CONT)

  Setting         SW1/7              SW1/8                  U1

  V.11 DTE          On                On          V.11 module in position
                                                             1

  V.11 DCE          On                On          V.11 module in position
                                                             2

  V.24 DTE         Off                Off         V.24 module in position
                                                             1

  V.24 DCE         Off                Off         V.24 module in position
                                                             2

  V.35 DTE          On                On          V.35 module in position
                                                             1

  V.35 DCE          On                On          V.35 module in position
                                                             2

  V.36 DTE          On                On          V.36 module in position
                                                             1

  V.36 DCE          On                On          V.36 module in position
                                                             2

    DSU             On                On           DSU module in position
                                                             1

Card Type          ISDN TA
ISDN Transfer Rate 64Kbps x 2
ISDN Protocol      Unidentified
Switch Type        Unidentified

[Image]

                                CONNECTIONS

        Function            Label            Function             Label

  Line in/out                CN1       Line in/out                 CN3

  Header to main board       CN2B
  (on both front and
  back of card)

            Note:Two connectors are provided so the user can daisy-chain
            devices on the S/T bus.

                        USER CONFIGURABLE SETTINGS

                   Setting                      Label        Position

     S/T bus not terminated                     SW1            Off

      S/T bus terminated                         SW1            On

Card Type          ISDN TA
ISDN Transfer Rate 64Kbps x 2
ISDN Protocol      Unidentified
Switch Type        Unidentified

[Image]

                                CONNECTIONS

        Function            Label            Function             Label

  Line out                   CN1       Header to main board       CN2B
                                       (on both front and
                                       back of card)

VANGUARD 305 (DSU DAUGHTERCARD)

Card Type           DDS DSU
DSU Transfer Rate   56Kbps
Modulation Protocol Unidentified

[Image]

                                CONNECTIONS

        Function            Label            Function             Label

  Line out                   CN1       Header to main board       CN2B
                                       (on both front and
                                       back of card)

