
WILDCARD TECHNOLOGIES, INC.

SATISFAXTION MOBILE PDMCIA9023COMBO

Card Type                    Modem (asynchronous), Ethernet
Chipset                      Intel 82595TX
Maximum Onboard Memory       160KB DRAM/128KB PROM
Network Transfer Rate        10Mbps
Maximum Data Rate            28.8Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     PCMCIA Type II
Fax Class                    Class I & II
Data Modulation              Bell 103A/212A

                             ITU-T V.21, V.22, V.23, V.22bis, V.32,
                             V.32bis, V.34

                             Rockwell V.FC
Fax Modulation               Unidentified
Error Correction/Compression MNP5, MNP10, V.42, V.42bis
Topology                     Star
Wire Type                    Unshielded twisted pair
Boot ROM                     Not available

                                                                      52771

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, A/

  A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

  &C, &D, &F, &G, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \G, \J, \K, \L, \N

  %C, %L, %Q

                            Special AT Commands

  -K, -Q, *H, )M, @M, :E, +MS

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S24, S25,

  S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41,
  S46, S48, S82, S86, S91,

  S92, S95, S201

                         Proprietary AT Command Set

                AUTO-RETRAIN AND AUTO-FALLBACK/FALL-FORWARD

  Type:          Configuration

  Format:        AT [cmds] %En [cmds]

  Description:   Controls auto-retrain mode and fallback/fall-forward

    Command                              Function

      %E0        Auto-retrain disabled.

      %E1        Auto-retrain enabled.

      %E2        Auto-fallback/fall-forward enabled.

      %E3        Auto-retrain and fast disconnect enabled.

                                 AUTOSYNC

  Format           AT [cmds] S19=n [cmds]

  Default:         0

  Range:           0 - 63

  Unit:            Bit-mapped

  Description:     Sets options for Hayes AutoSync functions.

   Bit    Value                           Function

    0         0    Not used.

    1          0   BSC enabled.

              1    HDLC enabled.

    2          0   HDLC address detection disabled.

              1    HDLC address detection enabled.

    3          0   NRZI bit encoding enabled.

              1    NRZ bit encoding enabled.

    4          0   Mark idle enabled.

              1    Flag or sync idle enabled.

                           AUTOSYNC HDLC ADDRESS

  Type:          Register

  Format:        AT [cmds] S20=n [cmds]

  Default:       0

  Range:         0-255

  Unit:          Unidentified

  Description:   Sets the HDLC address or BSC character.

                               COUNTRY CODE

  Type:          Configuration

  Format:        AT [cmds] *NCnn [cmds]

  Description:   Changes the country code of the modem to nn.

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

           DJ            MNP10 link will be negotiated at 1200bps for
                         this call.

           DK            MNP10 power level adjustment enabled for this
                         call.

           DL            Re-dial last number.

           DP            Pulse dialing enabled.

           DR            Answer mode enabled; originate mode disabled
                         following handshake initiation.

          DS=n           Dial stored telephone number n.

           DT            Tone dialing enabled.

           DW            Dialing resumed following dial tone detection.

           D,            Dialing paused for amount of time specified in
                         S8 register.

         D"WXY"          Optional method of denoting telephone numbers.
                         Letters enclosed in quotes are interpreted as
                         numbers according to the system found on a
                         telephone keypad.

           D!            Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

           D@            Wait for Quiet Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

           D$            Wait for prompt tone detection function enabled.
                         Modem waits for prompt tone for amount of time
                         specified by the S7 command.

           D;            Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

           D^            Calling tone toggled from current setting for
                         this call.

                              PULSE DIAL CODE

  Type:          Configuration

  Format:        AT [cmds] *Zn [cmds]

  Description:   Sets the currently active pulse dialing code.

    Command                              Function

      *Z0         Use dial code 0.

      *Z1         Use dial code 1.

                          DISPLAY STORED NUMBERS

  Type:          Immediate

  Format:        AT [cmds] \F [cmds]

  Description:   Displays all stored phone numbers.

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options.

    Command                              Function

      &K0        Flow control disabled.

      &K3        RTS/CTS flow control enabled.

      &K4        XON/XOFF flow control enabled.

      &K5        Transparent XON/XOFF flow control enabled.

      &K6        RTS/CTS and XON/XOFF flow control enabled.

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports modem model and speed

       I1        Reports ROM checksum

       I2        Tests and reports ROM checksum

       I3        Reports firmware revision.

       I5        Reports country code.

                     REQUEST LIST OF FORBIDDEN NUMBERS

  Type:          Immediate

  Format:        AT [cmds] *B [cmds]

  Description:   Requests the list of forbidden numbers from the modem.

                      REQUEST LIST OF DELAYED NUMBERS

  Type:          Immediate

  Format:        AT [cmds] *D [cmds]

  Description:   Requests the list of delayed numbers from the modem.

