
WISECOM, INC.

WS-2814IM6

Card Type                    Modem (asynchronous)
Chipset                      Rockwell
Maximum Data Rate            33.6Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     8-bit ISA
Fax Class                    Class I & II
Data Modulation              Bell 103A/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34

                             Rockwell V.FC
Fax Modulation               ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis

[Image]

                                CONNECTIONS

          Function             Label           Function             Label

  Line in                      CN1     Line out                     CN2

         SERIAL PORT ADDRESS SELECTION

    Setting          SW1/1          SW1/2

  3F8h (COM1:)        On              On

  2F8h (COM2:)        Off             On

  3E8h (COM3:)        On             Off

  2E8h (COM4:)        Off            Off

                 INTERRUPT SELECTION

  Setting    SW1/3      SW1/4      SW1/5      SW1/6

   IRQ2        On        Off        Off        Off

   IRQ3       Off         On        Off        Off

   IRQ4       Off        Off        On         Off

   IRQ5       Off        Off        Off        On

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, comma, A/

  A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

  &C, &D, &F, &G, &K, &P, &S, &T, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \K, \N

  %C, %E, %L, %Q

                            Special AT Commands

  +MS

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S24, S25

  S26, S27, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48,
  S82, S86, S91, S92, S95

            Note: See MHI documentation for complete information.

  UNIDENTIFIED COMMANDS

   Command      Default

     S37           0

                         Proprietary AT Command Set

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Reports product identification code.

       I1        Reports ROM checksum.

       I2        Tests and reports ROM checksum.

       I3        Reports firmware revision and model ID.

       I6        Reports data pump ID.

                              PROTOCOL/SPEED

  Type:             Configuration

  Format:           AT [cmds] Fn [cmds]

  Description:      Selects the protocol and speed the modem will attempt
                    to connect at.

     Command                              Function

        F0          Auto-detect the highest common connect speed.

        F1          Select V.21 or Bell 103 at 300bps speed.

        F3          Select V.23 at 75/1200bps speed.

        F4          Select V.22 or Bell 212A at 1200bps speed.

        F5          Select V.22bis at 2400bps speed.

        F6          Select V.32 or V.32bis at 4800bps speed.

        F7          Select V.32bis at 7200bps speed.

        F8          Select V.32bis or V.32 at 9600bps speed.

        F9          Select V.32bis at 12Kbps speed.

       F10          Select V.32bis at 14.4Kbps speed.

