
ANGIA COMMUNICATIONS, INC.

HIGH SPEED V.32BIS

Card Type                    Modem (asynchronous)
Chipset                      Unidentified
Maximum Data Rate            14.4Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation              Bell 103A/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis
Fax Modulation               ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, MNP10, V.42, V.42bis
Fax Class                    Class II
Data Bus                     PCMCIA Type II

                                                                      53159

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, comma, A/

  A, B, E, H, L, M, N, O, Q, V, W, X, Y, Z

  &C, &D, &F, &G, &J, &L, &P, &R, &S, &T, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \C, \G, \J, \N, \V, \Y, \Z

  %A, %C, %L

                            Special AT Commands

  *H, )M, @M

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S24, S25, S26

  S27, S28, S36, S38

            Note: See MHI help file for complete information.

                         Proprietary AT Command Set

                                AUTO-REDIAL

  Type:                  Register

  Format:                AT [cmds] S41=n [cmds]

  Default:               0

  Range:                 0 - 10

  Unit:                  1 retry

  Description:           Sets the number of times the modem will
                         automatically redial a call that failed to
                         connect.

                     AUTO-RELIABLE FALLBACK CHARACTER

  Type:            Configuration

  Format:          AT [cmds] S46=n [cmds]

  Default:         13

  Range:           0 - 127

  Unit:            1 ASCII character

  Description:     Sets the character used as the auto-reliable fallback
                   character.

                  AUTO-RELIABLE FALLBACK CHARACTER ENABLE

  Type:          Configuration

  Format:        AT [cmds] &Nn [cmds]

  Description:   Enables or disables the auto-reliable fallback
                 character.

    Command                              Function

      &N0        Auto-reliable fallback character disabled.

      &N1        Auto-reliable fallback character enabled.

                  AUTO-RELIABLE TIME BUFFER CONFIGURATION

  Type:                  Configuration

  Format:                AT [cmds] &On [cmds]

  Description:           Controls the handling of incoming data during
                         the auto-reliable negotiation time period.

        Command                              Function

          &O0            Data is discarded.

          &O1            Date is sent to DTE.

                               AUTO-RETRAIN

  Type:          Configuration

  Format:        AT [cmds] &En [cmds]

  Description:   Controls auto-retrain mode.

    Command                              Function

      &E0        Auto-retrain disabled.

      &E1        Auto-retrain enabled.

                    ANSWER/ORIGINATE DETECTION PATTERNS

  Type:                  Configuration

  Format:                AT [cmds] &An [cmds]

  Description:           Selects whether the modem will use answer and
                         originate detection patterns in originate mode.

        Command                              Function

          &A0            Answer and originate detection patterns disabled
                         in originate mode.

          &A1            Answer and originate detection patterns enabled
                         in originate mode.

                          BIT-MAPPED REGISTER S39

  Format:                AT [cmds] S39=n [cmds]

  Default:               0

  Range:                 0 - 187

  Description:           Controls power-up profile, local serial port
                         speed, break type, and auto-retrain.

      Bit         Value                       Function

      1, 0             00   Restore profile 0 on power-up.

                       01   Restore profile 1 on power-up.

                       10   Restore profile 2 on power-up.

                      11    Restore profile 3 on power-up.

       2               0    Not used.

       3                0   Local serial port speed set with S23.

                       1    Local serial port speed fixed at 115.2Kbps.

      5, 4             00   Break sent with transmitted data.

                       01   Break sent to remote modem immediately.

                      10    Break sent to remote modem and buffers
                            cleared.

       6               0    Not used.

       7                0   Auto-retrain enabled.

                       1    Auto-retrain disabled.

                          BIT-MAPPED REGISTER S49

  Format:             AT [cmds] S49=n [cmds]

  Default:            Unidentified

  Range:              0 - 148

  Description:        Controls flow control type and the compromise
                      equalizer.

     Bit        Value                        Function

    4 - 0         00000   Flow control disabled.

                  00011   RTS/CTS flow control enabled.

                  00100   XON/XOFF flow control enabled.

                  01000   Unidirectional transparent XON/XOFF flow
                          control enabled.
                  01100
                          Local transparent XON/XOFF flow control
                  10000   enabled.

                 10100    Internal XON/XOFF flow control enabled.

                          Internal local XON/XOFF flow control enabled.

     6, 5            00   Not used.

      7                0  Compromise equalizer enabled.

                      1   Compromise equalizer disabled.

                                BREAK TYPE

  Type:          Configuration

  Format:        AT [cmds] &In [cmds]

  Description:   Configures action of break signal.

    Command                              Function

      &I0        Break sent with transmitted data.

      &I1        Break sent to remote modem immediately.

      &I2        Break sent to remote modem and buffers cleared.

                                BREAK TYPE

  Type:          Configuration

  Format:        AT [cmds] \Kn [cmds]

  Description:   Configures action of break signal.

    Command                              Function

      \K1        Break sent to remote modem and buffers cleared.

      \K3        Break sent to remote modem immediately.

      \K5        Break sent with transmitted data.

                            COMMUNICATIONS MODE

  Type:          Configuration

  Format:        AT [cmds] &Qn [cmds]

  Description:   Selects the communications mode the modem will use.

    Command                              Function

      &Q0        Modem will operate in asynchronous mode.

      &Q4        Modem will operate in direct mode.

      &Q5        Modem will use MNP reliable in asynchronous mode.

      &Q6        Modem will use V.42 auto-reliable asynchronous mode.

      &Q7        Modem will use V.42 reliable asynchronous mode.

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] &Un [cmds]

  Description:   Selects whether the modem will use data compression.

    Command                              Function

      &U0         Data compression disabled.

      &U1         Data compression enabled.

                     COMPRESSION/ERROR CORRECTION TYPE

  Type:                  Register

  Format:                AT [cmds] S44=n [cmds]

  Description:           Returns a value indicating the type of error
                         correction and compression in use for the last
                         connection.

         Value                               Meaning

           0             Last connection used no error correction.

           2             Last connection used MNP2 error correction.

           3             Last connection used MNP3 error correction.

           4             Last connection used MNP4 error correction.

           5             Last connection used MNP5 compression.

           6             Last connection used V.42 error correction.

           7             Last connection used V.42bis compression.

                              CONNECTION TYPE

  Type:             Register

  Format:           AT [cmds] S43? [cmds]

  Description:      Returns a value indicating the type and speed of the
                    last connection.

      Value                                Meaning

        0           Last connection was at 300bps with no
                    error-correction.

        1           Last connection was at 1200bps with no
                    error-correction.

        2           Last connection was at 2400bps with no
                    error-correction.

        3           Last connection was at 1200bps in MNP mode.

        4           Last connection was at 2400bps in MNP mode.

        5           Last connection was at 1200bps in V.42 mode.

        6           Last connection was at 2400bps in V.42 mode.

        7           Last connection was at 4800bps with no
                    error-correction.

        8           Last connection was at 4800bps in MNP mode.

        9           Last connection was at 4800bps in V.42 mode.

        10          Last connection was at 9600bps with no
                    error-correction.

        11          Last connection was at 9600bps in MNP mode.

        12          Last connection was at 9600bps in V.42 mode.

        13          Last connection was at 300bps in MNP mode.

        14          Last connection was at 300bps in V.42 mode.

        15          Last connection was at 7200bps with no
                    error-correction.

        16          Last connection was at 7200bps in MNP mode.

        17          Last connection was at 7200bps in V.42 mode.

        18          Last connection was at 12Kbps with no
                    error-correction.

        19          Last connection was at 12Kbps in MNP mode.

        20          Last connection was at 12Kbps in V.42 mode.

        21          Last connection was at 14.4Kbps with no
                    error-correction.

        22          Last connection was at 14.4Kbps in MNP mode.

        23          Last connection was at 14.4Kbps in V.42 mode.

                         CONNECTION FAILURE CODES

  Type:            Register

  Format           AT [cmds] S45? [cmds]

  Description:     Returns a value which indicate the cause of a
                   connection failure.

      Value                               Meaning

        0          Carrier signal lost.

        1          User interrupted the connection.

        2          Train sequence failed.

        3          Retrain sequence failed.

        4          Inactivity timer time limit reached.

        5          Long Space Disconnect time limit reached.

        6          Remote modem failed to respond to feature negotiation.

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials the telephone number indicated according
                         to any modifiers included in the string.

        Command                              Function

           DJ            MNP10 link will be negotiated at 1200bps for
                         this call.

           DK            MNP10 power level adjustment enabled for this
                         call.

           DL            Re-dial last number.

           DP            Pulse dialing enabled.

           DR            Answer mode enabled; originate mode disabled
                         following handshake initiation.

          DS=n           Dial stored telephone number n.

           DT            Tone dialing enabled.

           DW            Dialing resumed following dial tone detection.

           D,            Dialing paused for amount of time specified in
                         S8 register.

           D/            Dialing paused for 1/8 second.

           D!            Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

           D@            Wait for Quiet Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

           D;            Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                          DISCONNECT BUFFER DELAY

  Type:                  Configuration

  Format                 AT [cmds] %Dn [cmds]

  Default:               20

  Range:                 0-255

  Unit:                  .1 second

  Description:           Sets maximum duration allowed during buffered
                         data calls for modem to perform clearing
                         functions after losing carrier-signal or
                         receiving a clear call signal from the remote
                         modem and before initiating hang-up process. A
                         value of 0 causes the modem to hang up without
                         waiting.

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Displays product identification code.

       I1        Displays ROM checksum.

       I2        Tests and reports ROM checksum.

       I3        Displays firmware revision.

       I4        Displays ASCII test string.

       I5        Displays chipset revision.

                          DISPLAY STORED PROFILES

  Type:           Immediate

  Format:         AT [cmds] \Sn [cmds]

  Description:    Displays the requested stored information.

    Command                              Function

      \S0         Displays stored profiles 0 and 1, and stored numbers 0
                  - 2.

      \S1         Displays stored profiles 2 and 3, and stored numbers 0
                  - 3.

                          DISPLAY STORED PROFILES

  Type:           Immediate

  Format:         AT [cmds] &Vn [cmds]

  Description:    Displays the requested stored information.

    Command                              Function

      &V0         Displays stored profiles 0 and 1, and stored numbers 0
                  - 2.

      &V1         Displays stored profiles 2 and 3, and stored numbers 0
                  - 3.

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options.

    Command                              Function

      &K0        Flow control disabled.

      &K3        RTS/CTS flow control enabled.

      &K4        XON/XOFF flow control enabled.

      &K8        Unidirectional transparent XON/XOFF flow control
                 enabled.

      &K12       Local transparent XON/XOFF flow control enabled.

      &K16       Internal XON/XOFF flow control enabled.

      &K20       Internal local XON/XOFF flow control enabled.

                       FLOW CONTROL CHARACTER - XON

  Type:          Register

  Format:        AT [cmds] S47=n [cmds]

  Default:       17

  Range:         0-255

  Unit:          1 ASCII character

  Description:   Sets the character used to represent XON.

                       FLOW CONTROL CHARACTER - XOFF

  Type:          Register

  Format:        AT [cmds] S48=n [cmds]

  Default:       10

  Range:         0-255

  Unit:          1 ASCII character

  Description:   Sets the character used to represent XOFF.

                             INACTIVITY TIMER

  Type:                  Register

  Format:                AT [cmds] S40=n [cmds]

  Default:               0

  Range:                 0 - 255

  Unit:                  1 minute

  Description:           Sets the length of time that the modem does not
                         receive information before it disconnects; S40=0
                         will disable.

                                LINE SPEED

  Type:                 Register

  Format                AT [cmds] S37=n [cmds]

  Description:          Sets the maximum allowable data exchange rate
                        attempted during handshaking process.

       Command                              Function

        S37=0           Speed of last connection

        S37=3           Set speed to 300bps.

        S37=5           Set speed to 1200bps.

        S37=6           Set speed to 2400bps.

        S37=7           Set speed to 4800bps.

        S37=9           Set speed to 9600bps.

        S37=10          Set speed to 9600bps.

        S37=11          Set speed to 300bps.

        S37=15          Set speed to 4800bps.

        S37=16          Set speed to 7200bps.

        S37=17          Set speed to 9600bps.

        S37=18          Set speed to 12Kbps.

        S37=19          Set speed to 14.4Kbps.

                             LOCK SERIAL PORT

  Type:          Configuration

  Format:        AT [cmds] &Bn [cmds]

  Description:   Sets operation of serial port speed.

    Command                              Function

      &B0        Serial speed follows connect speed.

      &B1        Serial speed locked.

               TRANSMISSION LEVEL ATTENUATION - LEASED LINE

  Type                Register

  Format              AT [cmds] S35=n [cmds]

  Default             9

  Range               0 - 15

  Unit                -1 dBm

  Description         Sets the signal attenuation level for transmission
                      over leased phone lines.

                        V.32 - COMPROMISE EQUALIZER

  Type%          Configuration

  Format%        AT [cmds] %En [cmds]

  Description%   Controls V.32 compromise equalizer.

    Command                              Function

      %E0        Compromise equalizer disabled.

      %E1        Compromise equalizer enabled.

