
NETCOMM LIMITED

THE OFFICIAL X-FILES MODEM 336 (MNP10)

Card Type                    Modem (asynchronous)
Chipset                      Unidentified
Maximum Data Rate            33.6Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation              Bell 103A, 212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34

                             Rockwell V.FC
Fax Modulation               ITU-T V.17, V.27ter, V.29
Error Correction/Compression MNP5, MNP10, V.42, V.42bis
Fax Class                    Class I & II
Data Bus                     Serial

                                                                      53447

                          DIAGNOSTIC LED(S)

    LED        Color      Status               Condition

     TM         Red         On           Modem is in test mode

     TM         Red         Off        Modem is not in test mode

     TD         Red      Blinking      Modem is transmitting data

     TD         Red         Off      Modem is not transmitting data

     RD         Red      Blinking       Modem is receiving data

     RD         Red         Off       Modem is not receiving data

     OH         Red         On             Modem is off-hook

     OH         Red         Off             Modem is on-hook

     CD         Red         On          Carrier signal detected

     CD         Red         Off       Carrier signal not detected

     AA         Red         On            Auto-answer enabled

     AA         Red         Off           Auto-answer disabled

     AA         Red      Blinking           Phone is ringing

     TR         Red         On             DTR signal is high

     TR         Red         Off            DTR signal is low

     CP         Red         On            Compression enabled

     CP         Red         Off           Compression disabled

     EC         Red         On          Error correction enabled

     EC         Red         Off        Error correction disabled

   POWER        Red         On                Power is on

   POWER        Red         Off               Power is off

   MISCELLANEOUS TECHNICAL NOTES

            Diagram not available.

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, comma, A/

  A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

  &C, &D, &F, &G, &K, &Q, &R, &S, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \G, \L, \N, \V

  %C, %E, %L, %Q

                            Special AT Commands

  :E, *H, -K, )M, @M, +MS, -Q

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S24, S25,
  S29, S30, S32, S33, S38

  S48, S82, S86, S95

            Note: See MHI help file for complete information.

     UNIDENTIFIED COMMANDS

    Command         Default

       \K        Unidentified

       *S        Unidentified

                         Proprietary AT Command Set

                               CALLING TONE

  Type:                Configuration

  Format:              AT [cmds] #Cn [cmds]

  Description:         Controls whether the modem will send a V.25
                       calling tone when originating a call.

  Note:                This command may not work on all THE OFFICIAL
                       X-FILES MODEM 336 (MNP10)s.

       Command                              Function

         #C0           Calling tone disabled.

         #C1           1300Hz V.25 calling tone enabled.

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#>;[cmds]

  Description:           Dials the telephone number indicated according
                         to any modifiers included in the string.

        Command                             Function

          DJ             MNP10 link will be negotiated at 1200bps for
                         this call.

          DK             MNP10 power level adjustment enabled for this
                         call.

          DL             Re-dial last number.

          DP             Pulse dialing enabled.

         DS=n            Dial stored telephone number n.

          DT             Tone dialing enabled.

          DW             Dialing resumed following dial tone detection.

                               DIAL (CON'T)

      Command                              Function

         D,           Dialing paused for amount of time specified in S8
                      register.

         D!           Flash function initiated. Modem commanded to go
                      off-hook for specified time before returning
                      on-hook.

         D@           Wait for Quiet Answer function enabled. Modem waits
                      until a "quiet answer," a ring-back signal followed
                      by silence up to the time specified in S7, is
                      received prior to executing the rest of the dial
                      string.

         D^           Calling tone disabled for this call.

         D;           Modem returned to idle state after dialing. The
                      semicolon can only be placed at the end of the dial
                      command.

                             DISTINCTIVE RING

  Format:                 AT [cmds] -SDR=n [cmds]

  Default:                0

  Range:                  0 - 7

  Description:            Selects which distinctive ring signals the
                          modem will respond to and how it will respond.

      Bit          Value                       Function

       0                 0   Respond to ring type 1 as RING.

                        1    Respond to ring type 1 as RING1.

        1                 0  Respond to ring type 2 as RING.

                         1   Respond to ring type 2 as RING2.

        2                 0  Respond to ring type 3 as RING.

                         1   Respond to ring type 3 as RING3.

                   DISPLAY CONFIGURATION AND STATISTICS

  Type:                Immediate

  Format:              AT [cmds] \S [cmds]

  Description:         Displays the settings of all commands and
                       statistics about the current connection.

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Displays product identification code.

       I1        Displays ROM checksum.

       I2        Tests and displays ROM checksum result.

       I3        Displays firmware revision.

       I4        Displays feature bitmap.

       I9        Displays product name and version.

      I100       Plays the theme song to the X-Files.

                            FAX/DATA SWITCHING

  Type:                  Configuration

  Format:                AT [cmds] *SMn [cmds]

  Description:           Selects whether the modem will automatically
                         detect the type of incoming call and switch to
                         the appropriate mode.

        Command                              Function

         *SM0            Fax/data switching disabled.

         *SM1            Fax/data switching enabled.

                        FAX/DATA SWITCHING - MANUAL

  Type:                Configuration

  Format:              AT [cmds] *SC=<#> [cmds]

  Description:         Sets the modem to switch to fax mode when it
                       receives the indicated DTMF digit.

                          FAX/DATA SWITCHING MODE

  Type:          Configuration

  Format:        AT [cmds] *STn [cmds]

  Description:   Selects how the modem switches modes between data and
                 fax.

    Command                              Function

      *ST0       Manual switching only.

      *ST1       Automatic switching only.

      *ST2       Automatic or manual switching.

                              RINGBACK SIGNAL

  Type:                 Configuration

  Format:               AT [cmds] *SSn [cmds]

  Description:          Selects whether the modem will transmit a
                        ringback signal while the line is ringing.

       Command                              Function

         *SS0           Ringback signal disabled.

         *SS1           Ringback signal enabled.

