
UNIQUE HARDWARE CO., LTD.

FAXSENGER 34

Card Type                    Modem (synchronous/asynchronous)
Chipset                      Unidentified
Maximum Data Rate            28.8Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation              Bell 103A, 212A

                             ITU-T V.21, V.22, V.22bis, V.32, V.32bis,
                             V.34

                             Rockwell V.FC
Fax Modulation               ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis
Fax Class                    Class I & II
Data Bus                     Serial

[Image]

                                CONNECTIONS

          Function            Label            Function            Label

  4 AA alkaline cells (on      BAT     DC power in                  CN4
  bottom)

  Serial port                  CN1     Telephone line out           CN5

  Serial port                  CN2     Power switch                 SW1

  DC power in                  CN3

                             DIAGNOSTIC LED(S)

     LED         Color         Status                 Condition

     288         Green           On          Modem connected at 28.8Kbps

     288         Green           Off          Modem connected at slower
                                                    than 28.8Kbps

     144         Green           On          Modem connected at 14.4Kbps
                                                      or faster

     144         Green           Off          Modem connected at slower
                                                    than 14.4Kbps

     EC          Green           On           Error correction enabled

     EC          Green           Off          Error correction disabled

    LBAT         Green           On               Batteries are low

    LBAT         Green           Off             Batteries are good

     AA          Green           On              Auto-answer enabled

     AA          Green           Off            Auto-answer disabled

     AA          Green        Blinking            Phone is ringing

     CD          Green           On            Carrier signal detected

     CD          Green           Off         Carrier signal not detected

     OH          Green           On               Modem is off-hook

     OH          Green           Off              Modem is on-hook

     OH          Green        Blinking        Modem is dialing in pulse
                                                        mode

                         DIAGNOSTIC LED(S) (CON'T)

     LED         Color        Status                Condition

     SD          Green          On          Modem is transmitting data

     SD          Green         Off        Modem is not transmitting data

     RD          Green          On           Modem is receiving data

     RD          Green         Off         Modem is not receiving data

     TR          Green          On              DTR signal is high

     TR          Green         Off              DTR signal is low

     PWR         Green          On                 Power is on

     PWR         Green         Off                 Power is off

   FAX/TM        Green          On        Modem is connected in FAX mode

   FAX/TM        Green       Blinking         Modem is in test mode

   FAX/TM        Green         Off         Modem is not connected in FAX
                                                       mode

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, comma, A/

  A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

  &C, &D, &F, &G, &K, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z

                           Extended AT Commands

  \A, \B, \G, \K, \L, \N

  %C, %E, %L, %Q

                            Special AT Commands

  +MS

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S25, S26

  S27, S29, S30, S31, S32, S33, S36, S38, S40, S41, S46, S48, S82, S86,
  S95

            Note: See MHI help file for complete information.

                         Proprietary AT Command Set

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#>;[cmds]

  Description:           Dials the telephone number indicated according
                         to any modifiers included in the string.

        Command                              Function

           DJ            MNP10 link will be negotiated at highest
                         possible speed for this call.

           DL            Re-dial last number.

           DP            Pulse dialing enabled.

          DS=n           Dial stored telephone number n.

           DT            Tone dialing enabled.

           DW            Dialing resumed following dial tone detection.

           D,            Dialing paused for amount of time specified in
                         S8 register.

           D!            Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

           D@            Wait for Quiet Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

           D^            Calling tone disabled for this call.

           D;            Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Displays product identification code.

       I1        Displays ROM checksum.

       I2        Tests and displays ROM checksum result.

       I3        Displays firmware revision.

       I4        Displays chipset model.

       I5        Displays country code.

       I6        Displays product name.

                             DISTINCTIVE RING

  Type:            Configuration

  Format:          AT [cmds] &In [cmds]

  Description:     Selects which distinctive ring signals the modem will
                   respond to.

     Command                              Function

       &I0         Modem will respond to any ring signal.

       &I1         Modem will only respond to Homefax II type B ring
                   signal.

                               FLOW CONTROL

  Type:          Register

  Format         AT [cmds] S39=n [cmds]

  Description:   Selects the type of flow control the modem will use.

    Command                              Function

     S39=0       Flow control disabled.

     S39=3       RTS/CTS flow control enabled.

     S39=4       XON/XOFF flow control enabled.

     S39=5       Transparent XON/XOFF flow control enabled.

     S39=6       Both RTS/CTS and XON/XOFF flow control enabled.

                                LINE SPEED

  Type:                  Register

  Format:                AT [cmds] S37=n [cmds]

  Description:           Sets the maximum allowable data exchange rate
                         attempted during the handshaking process.

        Command                             Function

         S37=0           Attempt to connect at fastest common speed.

         S37=1           Set speed to 300bps.

         S37=2           Set speed to 300bps.

         S37=3           Set speed to 300bps.

         S37=5           Set speed to 1200bps.

         S37=6           Set speed to 2400bps.

         S37=7           Attempt to connect with V.23.

         S37=8           Set speed to 4800bps.

         S37=9           Set speed to 9600bps.

        S37=10           Set speed to 12Kbps.

        S37=11           Set speed to 14.4Kbps.

        S37=12           Set speed to 7200bps.

                              PROTOCOL/SPEED

  Type:             Configuration

  Format:           AT [cmds] Fn [cmds]

  Description:      Selects the protocol and speed the modem will attempt
                    to connect at.

     Command                              Function

        F0          Auto-detect the highest common connect speed.

        F1          Select V.21 or Bell 103 at 300bps speed.

        F4          Select V.22 or Bell 212A at 1200bps speed.

        F5          Select V.22bis at 2400bps speed.

        F6          Select V.32 or V.32bis at 4800bps speed.

        F7          Select V.32bis at 7200bps speed.

        F8          Select V.32bis or V.32 at 9600bps speed.

        F9          Select V.32bis at 12Kbps speed.

       F10          Select V.32bis at 14.4Kbps speed.

