
AMT INTERNATIONAL, INC.

STAR 9600 (ERROR CORRECTION AND COMPRESSION)

Card Type                    Modem (asynchronous)
Chipset                      Unidentified
Maximum Data Rate            9600bps
Data Modulation              Bell 103A, 212A

                             ITU-T V.21, V.22, V.22bis, V.32
Error Correction/Compression MNP5, V.42, V.42bis
Data Bus                     8-bit ISA
Card Size                    Full height (length is unidentified)

[Image]

                                CONNECTIONS

          Function             Label           Function             Label

  Telephone line out           CN1     Telephone line in            CN2

                       SERIAL PORT ADDRESS SELECTION

    Setting          J1/A          J1/B           J1/C           J1/D

  3F8h (COM1:)      Closed         Open           Open           Open

  2F8h (COM2:)       Open         Closed          Open           Open

  3E8h (COM3:)       Open          Open          Closed          Open

  2E8h (COM4:)       Open          Open           Open          Closed

                 INTERRUPT SELECTION

  Setting    JP2/A      JP2/B      JP2/C      JP2/D

     2       Closed      Open      Open       Open

     3        Open      Closed     Open       Open

     4        Open       Open     Closed      Open

     5        Open       Open      Open      Closed

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, comma, A/

  A, D, E, H, L, M, O, Q, V, X, Z

  &C, &D, &G, &S, &V, &W, &Y, &Z

                           Extended AT Commands

  %A, %C

  \A, \C, \E, \G, \J, \K, \N, \O, \Q, \T, \U, \X, \Y, \Z

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S24, S25,
  S26

            Note: See MHI help file for complete information.

                         Proprietary AT Command Set

                          COMMUNICATION PROTOCOLS

  Type:           Configuration

  Format:         AT [cmds] Bn [cmds]

  Description:    Selects the communication protocol for low-speed data
                  calls.

    Command                              Protocol

       B0         Modem will use ITU-T V.22 at 1200bps.

       B1         Modem will use Bell 212A at 1200bps.

       B2         Modem will only connect with V.22bis, V.22, or Bell
                  103.

       B3         Modem will only connect with V.22, or Bell 103.

       B4         Modem will only connect with Bell 103.

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Displays product identification code.

       I1        Displays ROM checksum.

       I2        Tests and displays ROM checksum result.

       I3        Displays firmware part number and revision.

       I4        Displays modem configuration.

       I5        Displays firmware date.

                   DISPLAY CONFIGURATION AND STATISTICS

  Type:                Immediate

  Format:              AT [cmds] \S [cmds]

  Description:         Displays the settings of all commands and
                       statistics about the current connection.

                            DSR AND CTS SIGNALS

  Type:                  Configuration

  Format:                AT [cmds] \Dn [cmds]

  Description:           Controls the behaviour of the DSR and CTS
                         signals.

        Command                              Function

          \D0            DSR and CTS forced high.

          \D1            CTS follows CD. If &C is not set to 1 then DSR
                         also follows CD, otherwise it follows OH.

          \D2            DSR and CTS follow CD.

                             ENQ/ACK PROTOCOL

  Type:          Configuration

  Format:        AT [cmds] \Hn [cmds]

  Description:   Selects the Hewlett-Packard ENQ/ACK protocol.

    Command                              Function

      \H0         ENQ/ACK protocol disabled.

      \H1         ENQ/ACK protocol enabled in terminal mode.

      \H2         ENQ/ACK protocol enabled in host mode.

                           EXTENDED RESULT CODES

  Type:            Configuration

  Format:          AT [cmds] \Vn [cmds]

  Description:     Selects error correction and compression extended
                   result codes.

     Command                              Function

       \V0         Error correction and compression extended result codes
                   disabled.

       \V1         /REL extended result codes enabled.

       \V2         V.42 extended result codes enabled.

                          FACTORY DEFAULT PROFILE

  Type:                  Immediate

  Format:                AT [cmds] &F [cmds]

  Description:           Returns the command settings to the values found
                         in the specified factory default profile.

        Command                              Function

          &F0            Resets commands to the standard factory profile.

          &F1            Resets commands to the MNP factory profile.

          &F2            Resets commands to the LAPM factory profile.

