
MOTOROLA, INC.

FT100 M

Card Type             T1 CSU/DSU, Ethernet
Chip Set              Unidentified
I/O Options           Monitor ports, alarm port
Network Transfer Rate 10Mbps
Topology              Star
Wiring Type           Unshielded twisted pair
Transfer Rate         1.544Mbps
Data Bus              Serial
Protocol              AMI, B8ZS
Frame Type            SF, ESF

[Image]

                                CONNECTIONS

         Function            Label            Function            Label

  Monitor receive             CN1      Serial control port         CN6

  Monitor transmit            CN2      DSX-1, RS-232, RS-449,      CN7
                                       RS-530, or V.35 serial
                                       data port 2 (on
                                       daughterboard)

  T1 interface                CN3      DC power in                 CN8

  UTP connector               CN4      Alarm port (see pinout      SC1
                                       below)

  DSX-1, RS-232, RS-449,      CN5
  RS-530, or V.35 serial
  data port 1 (on
  daughterboard)

            Note:Standard serial ports are provided on included adapter
            cables.

                                SC1 PINOUT

           Function             Pin             Function             Pin

  Normally closed connection     1      Signal common                 3

  Normally open connection       2      Not used                      4

                        USER CONFIGURABLE SETTINGS

                 Setting                    Label          Position

     Signal ground connected to chassis      E1       Pins 2 & 3 closed
      ground

      Signal ground not connected to          E1       Pins 1 & 2 closed
      chassis ground

     Factory configured - do not alter      S1/1        Unidentified

     Factory configured - do not alter      S1/2        Unidentified

     Factory configured - do not alter      S1/3        Unidentified

     Factory configured - do not alter      S1/4        Unidentified

     Factory configured - do not alter      S1/5        Unidentified

     Factory configured - do not alter      S1/6        Unidentified

     Factory configured - do not alter      S1/7        Unidentified

     Factory configured - do not alter      S1/8        Unidentified

     Factory configured - do not alter      S2/1        Unidentified

     Factory configured - do not alter      S2/2        Unidentified

     Factory configured - do not alter      S2/3        Unidentified

     Factory configured - do not alter      S2/4        Unidentified

     Factory configured - do not alter      S2/5        Unidentified

     Factory configured - do not alter      S2/6        Unidentified

     Factory configured - do not alter      S2/7        Unidentified

     Factory configured - do not alter      S2/8        Unidentified

     Factory configured - do not alter     S28/1             On

     Factory configured - do not alter     S28/2             On

     Factory configured - do not alter     S28/3             On

     Factory configured - do not alter     S28/4             On

     Factory configured - do not alter     S28/5             On

     Factory configured - do not alter     S28/6             On

     Factory configured - do not alter     S28/7             On

     Factory configured - do not alter     S28/8             Off

                    USER CONFIGURABLE SETTINGS (CONT)

                  Setting                      Label         Position

     One stop bit selected                    S29/5            On

      Two stop bits selected                   S29/5            Off

     8 data bits selected                     S29/6            On

      7 data bits selected                     S29/6            Off

                        CONTROL PORT CONFIGURATION

      Setting              E25               E26                E27

         DCE        Pins 1 & 2, 3 &    Pins 1 & 2, 3 &   Pins 1 & 2, 3 &
                        4 closed           4 closed          4 closed

          DTE        Pins 1 & 3, 2 &    Pins 1 & 3, 2 &   Pins 1 & 3, 2 &
                        4 closed           4 closed          4 closed

                        SERIAL PORT SPEED SELECTION

           Setting                    S29/1                  S29/2

              2400bps                  Off                    Off

              4800bps                  Off                    On

              9600bps                   On                    Off

            19.2Kbps                   On                    On

                           DATA PARITY SELECTION

           Setting                    S29/3                  S29/4

            Disabled                   On                    N/A

               Even                    Off                    On

                Odd                    Off                    Off

                          FLOW CONTROL SELECTION

            Setting                    S29/7                 S29/8

      Flow control disabled            On                    On

       XON/XOFF flow control            On                    Off
              enabled

        RTS/CTS flow control            Off                   On
              enabled

                             DIAGNOSTIC LED(S)

     LED         Color         Status                Condition

    TXD2         Green           On         Data is being transmitted to
                                                       port 2

    TXD2         Green          Off         Data is not being transmitted
                                                     to port 2

    RXD2         Green           On          Data is being received from
                                                       port 2

    RXD2         Green          Off          Data is not being received
                                                    from port 2

    TXD1         Green           On         Data is being transmitted to
                                                       port 1

    TXD1         Green          Off         Data is not being transmitted
                                                     to port 1

    RXD1         Green           On          Data is being received from
                                                       port 1

    RXD1         Green          Off          Data is not being received
                                                    from port 1

     YEL          Red            On            Yellow alarm condition
                                                      detected

     YEL          Red           Off          Yellow alarm condition not
                                                      detected

     AIS          Red            On           All Ones Signal detected

     AIS          Red           Off         All Ones Signal not detected

                         DIAGNOSTIC LED(S) (CONT)

    LED          Color         Status                 Condition

    LOS           Red            On            Loss of signal detected

    LOS           Red            Off         Loss of signal not detected

    SYN          Green           On             Valid framing pattern
                                             received from T1 interface

    SYN          Green           Off          Valid framing pattern not
                                             received from T1 interface

    PWR          Green           On                  Power is on

    PWR          Green           Off                Power is off

                        USER CONFIGURABLE SETTINGS

                   Setting                      Label        Position

     Factory configured - do not alter          SW1            Off

     Factory configured - do not alter          SW2            Off

     Factory configured - do not alter          SW3            On

     Factory configured - do not alter          SW4            On

     Factory configured - do not alter          SW5            Off

     Factory configured - do not alter          SW6            On

     Factory configured - do not alter          SW7            Off

     Factory configured - do not alter          SW8            Off

    MISCELLANEOUS TECHNICAL NOTES

            Diagram not available.

FT100 M (RS-449/530 INTERFACE)

                     MISCELLANEOUS TECHNICAL NOTES

            Diagram not available.

            The card's jumper(s) must be set for Test Mode operation.

