
NEWCOM, INC.

336IFXSP(C)

Card Type                    Modem (asynchronous)
Chipset                      Unidentified
I/O Options                  Audio line out, microphone in, speaker out,
                             voice, speakerphone
Maximum Data Rate            33.6Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation              Bell 103A, 212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34
Fax Modulation               ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis
Fax Class                    Class I
Data Bus                     16-bit ISA
Card Size                    Full height, half length

[Image]

                                CONNECTIONS

          Function             Label            Function            Label

  Telephone line out            CN1     Headphone line out          CN4

  Telephone line in             CN2     Speaker out                 CN5

  Microphone in                 CN3

                                            PLUG-N-PLAY

         Setting                   JP1/A                    JP1/B                   JP1/C

         Enabled                   Closed                  Closed                   Closed

         Disabled                   Open                    Open                     Open

            Note: If Plug-N-Play mode is enabled, all other jumper settings must also be set for
            Plug-N-Play.

                            INTERRUPT SELECTION

   Setting      JP1/D   JP1/E    JP1/F    JP1/G    JP1/H    JP1/I    JP1/J

      3         Open     Open     Open     Open     Open    Open     Closed

      4         Open     Open     Open     Open     Open    Closed   Open

      5         Open     Open     Open     Open    Closed   Open     Open

      7         Open     Open     Open    Closed    Open    Open     Open

      10        Closed   Open     Open     Open     Open    Open     Open

      11        Open    Closed    Open     Open     Open    Open     Open

      12        Open     Open    Closed    Open     Open    Open     Open

  Plug-N-Play   Closed  Closed   Closed   Closed   Closed   Closed   Closed

                       SERIAL PORT ADDRESS SELECTION

    Setting         JP1/K          JP1/L          JP1/M         JP1/N

  3F8h (COM1:)      Closed        Closed          Open           Open

  2F8h (COM2:)      Closed         Open           Open          Closed

  3E8h (COM3:)       Open         Closed         Closed          Open

  2E8h (COM4:)       Open          Open          Closed         Closed

  Plug-N-Play        Open          Open           Open           Open

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, comma, A/

  A, C, D, E, F, H, L, M, N, O, P, Q, T, V, X, Y, Z

  &C, &D, &F, &G, &J, &K, &P, &S, &T, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \C, \G, \J, \N, \O, \Q, \T, \U, \X, \Y, \Z

  %A, %C, %E, %G

                            Special AT Commands

  -C, "H, -J, "O

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S25, S27

  S30, S31, S33, S37

            Note: See MHI help file for complete information.

                              IS-101 COMMANDS

                                +V Commands

  +VBT, +VCID, +VCSD, +VDR, +VEM, +VGM, +VGR, +VGS, +VGT, +VIP, +VIT,
  +VLS, +VNH, +VRA, +VRN

  +VRX, +VSD, +VSM, +VSP, +VTD, +VTS, +VTX, #VSPS

                                -S Commands

  -SAC, -SCD, -SDA, -SDS, -SER, -SFX, -SIC, -SIP, -SQR, -SSP, -SSQ, -SSR,
  -SSV

            Note: The functions of the IS-101 commands are unidentified.

                         Proprietary AT Command Set

                                             BREAK TYPE

  Type:                    Configuration

  Format:                  AT [cmds] \Kn [cmds]

  Description:             Configures action of break signal.

   Command         Break from DTE        Break from DTE     Modem receives \B    Break from remote
                                                                                       modem
                  Reliable/Normal         Direct mode
                       mode

     \K0        Enter command mode,   Send break to         Buffers cleared      Buffers cleared
                do not send break     remote modem          and break sent to    and break sent to
                to remote modem.      immediately, then     remote modem.        DTE.
                                      enter command
                                      mode.

     \K1        Buffers cleared and   Send break to         Buffers cleared      Buffers cleared
                break sent to         remote modem          and break sent to    and break sent to
                remote modem.         immediately.          remote modem.        DTE.

     \K2        Enter command mode,   Send break to         Send break to        Send break to DTE
                do not send break     remote modem          remote modem         immediately.
                to remote modem.      immediately, then     immediately.
                                      enter command
                                      mode.

     \K3        Send break to         Send break to         Send break to        Send break to DTE
                remote modem          remote modem          remote modem         immediately.
                immediately.          immediately.          immediately.

     \K4        Enter command mode,   Send break to         Send break to        Break sent with
                do not send break     remote modem          remote modem with    received data to
                to remote modem.      immediately, then     transmitted data.    the DTE.
                                      enter command
                                      mode.

     \K5        Send break with       Send break to         Send break to        Break sent with
                transmitted data.     remote modem          remote modem with    received data to
                                      immediately.          transmitted data.    the DTE.

                          COMMUNICATION PROTOCOLS

  Type:           Configuration

  Format:         AT [cmds] Bn [cmds]

  Description:    Selects the communication protocol for low-speed data
                  calls.

    Command                              Protocol

       B0         Modem will use ITU-T V.22 at 1200bps.

       B1         Modem will use Bell 212A at 1200bps.

       B2         Modem will use ITU-T V.23 at 1200/75bps.

       B3         Modem will use ITU-T V.23 at 75/1200bps.

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Displays product identification code.

       I1        Displays chip firmware revision.

       I2        Tests and displays ROM checksum result.

       I3        Displays modem chipset name.

       I5        Displays hardware configuration.

       I6        Displays country code.

       I7        Displays board firmware revision.

       I8        Displays chipset feature bitmap.

      I10        Displays board feature bitmap.

      I11        Displays board feature bitmap.

      I14        Displays digital SAFE device information.

      I20        Displays the revision level of the modem's voice
                 chipset.

      I21        Displays the revision level of the modem's voice
                 firmware.

      I22        Displays the voice chipset manufacturers name.

      I23        Displays the model name of the modem's voice chipset.

                             DISPLAY PROFILES

  Type:          Immediate

  Format:        AT [cmds] &Vn [cmds]

  Description:   Displays active and stored configuration profiles.

    Command                              Function

      &V0        Displays stored profile 0.

      &V1        Displays stored profile 1.

      &V3        Displays relay status and I/O information.

                           EXTENDED RESULT CODES

  Type:                  Configuration

  Format:                AT [cmds] Wn [cmds]

  Description:           Selects which result codes the modem will
                         report.

        Command                              Function

           W0            Enables CONNECT result codes to report DTE
                         speed.

           W1            Enables CONNECT result codes to report DTE
                         speed.

           W2            Enables CONNECT result codes to report DCE
                         speed.

           W3            Enables CONNECT result codes to report DTE speed
                         with error correction and compression
                         information.

           W4            Enables CONNECT result codes to report DTE speed
                         with modulation protocol, error correction, and
                         compression information.

                              MODE SELECTION

  Type:          Immediate

  Format:        AT [cmds] +FCLASS=n

  Description:   Sets what mode the modem will operate in.

    Command                              Function

   +FCLASS=0     Data mode.

   +FCLASS=1     Class 1 fax mode.

   +FCLASS=8     Voice mode.

   +FCLASS=80    IS-101 voice mode.

                              TRELLIS CODING

  Type:          Configuration

  Format:        AT [cmds] &Un [cmds]

  Description:   Selects whether the modem will use trellis coding.

    Command                              Function

      &U0         Trellis coding enabled.

      &U1         Trellis coding disabled.

