
OLICOM, INC.

OC-3232

Card Type                    Modem (synchronous/asynchronous), Token Ring
Modem Chipset                Rockwell RC288ACL
Network Chipset              Texas Instruments TMS380C30
Maximum Onboard Memory       160KB RAM/128KB Flash ROM
Boot ROM                     Not available
Network Transfer Rate        4Mbps/16Mbps
Topology                     Ring
Wire Type                    Shielded/Unshielded twisted pair
Maximum Data Rate            33.6Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation              Bell 103A, 212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34

                             Rockwell V.FC
Fax Modulation               Unidentified
Error Correction/Compression MNP5, MNP10EC, V.42, V.42bis
Fax Class                    Class I & II
Data Bus                     PCMCIA Type II

                                                                      53760

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, comma, A/

  A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

  &C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \G, \J, \K, \L, \N, \V

  %C, %E, %L, %Q

                            Special AT Commands

  :E, -K, @M, +MS

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S18, S24, S25, S26,
  S29, S30, S32, S33

  S36, S38, S39, S46, S48, S82, S86, S91, S92, S95, S201

            Note: See MHI help file for complete information.

     UNIDENTIFIED COMMANDS

    Command         Default

      S14        Unidentified

      S16        Unidentified

      S21        Unidentified

      S22        Unidentified

      S23        Unidentified

      S27        Unidentified

      S28        Unidentified

      S31        Unidentified

      S37        Unidentified

      S40        Unidentified

      S41        Unidentified

      S80        Unidentified

                         Proprietary AT Command Set

                             AUTOSYNC OPTIONS

  Type:                 Register

  Format                AT [cmds] S19=n [cmds]

  Default:              26

  Range:                0 - 30

  Description:          Controls AutoSync protocol, HDLC address
                        detection, bit coding type, and HDLC idle.

    Bit       Value                         Function

     0             0    Not used

     1              0   Binary synchronous protocol used.

                   1    HDLC protocol used.

     2              0   HDLC address detection disabled.

                   1    HDLC address detection enabled.

     3              0   NRZI bit coding used.

                   1    NRZ bit coding used.

     4              0   HDLC idle sends MARK.

                   1    HDLC idle sends FLAG or SYNC.

                           AUTOSYNC HDLC ADDRESS

  Type:          Register

  Format:        AT [cmds] S20=n [cmds]

  Default:       0

  Range:         0-255

  Unit:          Unidentified

  Description:   Sets the HDLC address and binary synchronous character.

                         CELLULAR STATUS INDICATOR

  Format:            AT [cmds] ^T6 [cmds]

  Default:           Read-only

  Range:             0-255

  Description:       Indicates the status of cellular phone.

     Bit      Value                         Function

      0             0  Cellular phone is not receiving a call.

                   1   Cellular phone is receiving a call.

      1             0   Cellular phone is not in use.

                   1    Cellular phone is in use.

      2             0   Cellular phone is not locked.

                   1    Cellular phone is locked.

      3             0   Cellular service detected.

                   1    Cellular service not detected.

      4             0   Cellular phone is powered off.

                   1    Cellular phone is powered on.

      5             0   Cellular driver is initialized.

                   1    Cellular driver is not initialized.

      6            0    Not used.

      7             0   Cellular cable not detected.

                   1    Cellular cable detected.

                               COUNTRY CODE

  Type:                  Configuration

  Format:                AT [cmds] *NCnn [cmds]

  Description:           Sets the modem's country code. The values and
                         associated meanings for this command are
                         unidentified.

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#>;[cmds]

  Description:           Dials the telephone number indicated according
                         to any modifiers included in the string.

        Command                              Function

           DJ            MNP10 link will be negotiated at 1200bps for
                         this call.

           DK            MNP10 power level adjustment enabled for this
                         call.

           DL            Re-dial last number.

           DP            Pulse dialing enabled.

           DR            Answer mode enabled; originate mode disabled
                         following handshake initiation.

          DS=n           Dial stored telephone number n.

           DT            Tone dialing enabled.

           DW            Dialing resumed following dial tone detection.

           D,            Dialing paused for amount of time specified in
                         S8 register.

           D!            Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

                               DIAL (CON'T)

      Command                              Function

         D@           Wait for Quiet Answer function enabled. Modem waits
                      until a "quiet answer," a ring-back signal followed
                      by silence up to the time specified in S7, is
                      received prior to executing the rest of the dial
                      string.

         D^           Calling tone disabled for this call.

         D;           Modem returned to idle state after dialing. The
                      semicolon can only be placed at the end of the dial
                      command.

                        DISPLAY BLACKLISTED NUMBERS

  Type:            Immediate

  Format:          AT [cmds] *B [cmds]

  Description:     Displays the list of all blacklisted numbers and their
                   statuses.

                          DISPLAY CELLULAR DRIVER

  Type:          Immediate

  Format:        AT [cmds] ^I [cmds]

  Description:   Displays cellular phone driver information.

                          DISPLAY DELAYED NUMBERS

  Type:           Immediate

  Format:         AT [cmds] *D [cmds]

  Description:    Displays the list of all delayed numbers and their
                  statuses.

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Displays product identification code.

       I1        Displays ROM checksum.

       I2        Tests and displays ROM checksum result.

       I3        Displays firmware revision.

       I5        Displays country code.

                          DISPLAY STORED NUMBERS

  Type:          Immediate

  Format:        AT [cmds] \F [cmds]

  Description:   Displays all stored telephone numbers.

                         DOWNLOAD CELLULAR DRIVER

  Type:          Immediate

  Format:        AT [cmds] ^C2 [cmds]

  Description:   Download cellular phone driver.

                            PULSE DIALING MODE

  Type:          Configuration

  Format:        AT [cmds] *Zn [cmds]

  Description:   Selects the type of pulse dialing the modem will use.

    Command                              Function

      *Z0        Modem will use pulse dialing type 0.

      *Z1        Modem will use pulse dialing type 1.

                      REMOTE CONFIGURATION CHARACTER

  Type:                  Register

  Format:                AT [cmds] S202=n [cmds]

  Default:               Unidentified

  Range:                 Unidentified

  Unit:                  1 ASCII character

  Description:           Defines the character that, when sent four times
                         within the guard time set by S12, will notify
                         the remote modem that a remote configuration
                         session has been requested.

