
ACTIONTEC ELECTRONICS, INC.

56K X2 DATA/FAX

Card Type                    Modem (asynchronous)
Chipset                      Unidentified
Maximum Data Rate            56Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation              Bell 103A, 212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34

                             U.S. Robotics x2
Fax Modulation               ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis
Fax Class                    Class I
Data Bus                     8-bit ISA
Card Size                    Full height, half length

[Image]

                                CONNECTIONS

          Function             Label           Function             Label

  Telephone line out           CN1     Telephone line in            CN2

                        USER CONFIGURABLE SETTINGS

                      Setting                        Label     Position

  Plug-N-Play enabled                                J3/C        Open

  Plug-N-Play disabled                               J3/C       Closed

         SERIAL PORT ADDRESS SELECTION

    Setting          J3/A            J3/B

  3F8h (COM1:)      Closed          Closed

  2E8h (COM2:)       Open           Closed

  3F8h (COM3:)      Closed           Open

  2E8h (COM4:)       Open            Open

  Plug-N-Play        Open            Open

                            INTERRUPT SELECTION

    Setting       J2/A        J2/B        J2/C        J2/D        J2/E

       2         Closed       Open        Open        Open        Open

       3          Open       Closed       Open        Open        Open

       4          Open        Open       Closed       Open        Open

       5          Open        Open        Open       Closed       Open

       7          Open        Open        Open        Open       Closed

  Plug-N-Play     Open        Open        Open        Open        Open

                 SUPPORTED STANDARD COMMANDS

                      Basic AT Commands

  +++, comma, A/

  A, B, D, E, F, H, L, M, O, Q, V, X, Y, Z

  &C, &D, &F, &G, &P, &R, &S, &T, &W, &Z

                         S-Registers

  The S-registers are unidentified.

            Note: See MHI help file for complete information.

                                BREAK TYPE

  Type:          Configuration

  Format:        AT [cmds] &Yn [cmds]

  Description:   Configures action of break signal.

    Command                              Function

      &Y0        Break empties buffer.

      &Y1        Break empties buffer and is sent immediately.

      &Y2        Break does not empty buffer and is sent immediately.

                             COMPRESSION MODE

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Selects the type of data compression that will be used.

    Command                              Function

      &K0        Data compression disabled.

      &K1        Auto-detect compression mode.

      &K2        Data compression enabled.

      &K3        MNP5 data compression only enabled.

                       CONNECTION SPEED LOWER LIMIT

  Type:            Configuration

  Format:          AT [cmds] &Un [cmds]

  Description:     Sets slowest allowed connection speed if &N is set to
                   1 or higher.

     Command                              Function

       &U0         No minimum connect speed.

       &U1         Set minimum connect speed to 300bps.

       &U2         Set minimum connect speed to 1200bps.

       &U3         Set minimum connect speed to 2400bps.

       &U4         Set minimum connect speed to 4800bps.

       &U5         Set minimum connect speed to 7200bps.

       &U6         Set minimum connect speed to 9600bps.

       &U7         Set minimum connect speed to 12Kbps.

       &U8         Set minimum connect speed to 14.4Kbps.

       &U9         Set minimum connect speed to 16.8Kbps.

       &U10        Set minimum connect speed to 19.2Kbps.

       &U11        Set minimum connect speed to 21.6Kbps.

       &U12        Set minimum connect speed to 24Kbps.

       &U13        Set minimum connect speed to 26.4Kbps.

       &U14        Set minimum connect speed to 28.8Kbps.

       &U15        Set minimum connect speed to 31.2Kbps.

       &U16        Set minimum connect speed to 33.6Kbps.

       &U17        Set minimum connect speed to 33.3Kbps.

       &U18        Set minimum connect speed to 37.3Kbps.

       &U19        Set minimum connect speed to 41.3Kbps.

       &U20        Set minimum connect speed to 42.6Kbps.

       &U21        Set minimum connect speed to 44Kbps.

       &U22        Set minimum connect speed to 45.3Kbps.

       &U23        Set minimum connect speed to 46.6Kbps.

       &U24        Set minimum connect speed to 48Kbps.

       &U25        Set minimum connect speed to 49.3Kbps.

       &U26        Set minimum connect speed to 50.6Kbps.

       &U27        Set minimum connect speed to 52Kbps.

       &U28        Set minimum connect speed to 53.3Kbps.

       &U29        Set minimum connect speed to 54.6Kbps.

       &U30        Set minimum connect speed to 56Kbps.

       &U31        Set minimum connect speed to 57.3Kbps.

                       CONNECTION SPEED UPPER LIMIT

  Type:                  Configuration

  Format:                AT [cmds] &Nn [cmds]

  Description:           Sets required connection speed if &U is set to
                         0; otherwise, sets fastest allowed connection
                         speed.

        Command                              Function

          &N0            No maximum connect speed.

          &N1            Set maximum connect speed to 300bps.

          &N2            Set maximum connect speed to 1200bps.

          &N3            Set maximum connect speed to 2400bps.

          &N4            Set maximum connect speed to 4800bps.

          &N5            Set maximum connect speed to 7200bps.

          &N6            Set maximum connect speed to 9600bps.

          &N7            Set maximum connect speed to 12Kbps.

          &N8            Set maximum connect speed to 14.4Kbps.

          &N9            Set maximum connect speed to 16.8Kbps.

          &N10           Set maximum connect speed to 19.2Kbps.

          &N11           Set maximum connect speed to 21.6Kbps.

          &N12           Set maximum connect speed to 24Kbps.

          &N13           Set maximum connect speed to 26.4Kbps.

          &N14           Set maximum connect speed to 28.8Kbps.

          &N15           Set maximum connect speed to 31.2Kbps.

          &N16           Set maximum connect speed to 33.6Kbps.

          &N17           Set maximum connect speed to 33.3Kbps.

          &N18           Set maximum connect speed to 37.3Kbps.

          &N19           Set maximum connect speed to 41.3Kbps.

          &N20           Set maximum connect speed to 42.6Kbps.

          &N21           Set maximum connect speed to 44Kbps.

          &N22           Set maximum connect speed to 45.3Kbps.

          &N23           Set maximum connect speed to 46.6Kbps.

          &N24           Set maximum connect speed to 48Kbps.

          &N25           Set maximum connect speed to 49.3Kbps.

          &N26           Set maximum connect speed to 50.6Kbps.

          &N27           Set maximum connect speed to 52Kbps.

          &N28           Set maximum connect speed to 53.3Kbps.

          &N29           Set maximum connect speed to 54.6Kbps.

          &N30           Set maximum connect speed to 56Kbps.

          &N31           Set maximum connect speed to 57.3Kbps.

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays modem properties.

    Command                              Function

       I0        Displays product identification code.

       I1        Tests and displays ROM checksum result.

       I2        Tests and displays RAM checksum result.

       I3        Displays product identification.

       I4        Displays current command settings.

       I5        Displays current NVRAM settings.

       I6        Displays current connections statistics.

       I7        Displays product configuration.

                           ERROR CORRECTION MODE

  Type:          Configuration

  Format:        AT [cmds] &Mn [cmds]

  Description:   Selects active error correction protocols.

    Command                              Function

      &M0        Normal mode only.

      &M4        Auto-detect mode.

      &M5        Error correction mode only.

                           EXTENDED RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] &An [cmds]

  Description:   Selects extended result codes.

    Command                              Function

      &A0        Extended result codes disabled.

      &A1        Error correction result codes enabled.

      &A2        V.32 result code enabled.

      &A3        Error correction and compression result codes enabled.

                       FLOW CONTROL - MODEM-TO-MODEM

  Type:          Configuration

  Format:        AT [cmds] &In [cmds]

  Description:   Selects the type of modem-to-modem flow control used.

    Command                              Function

      &I0        Software flow control disabled.

      &I1        XON/XOFF pass-through enabled.

      &I2        XON/XOFF pass-through disabled.

                             FLOW CONTROL TYPE

  Type:          Configuration

  Format:        AT [cmds] &Hn [cmds]

  Description:   Sets type of flow control used by modem.

    Command                              Function

      &H0        Flow control disabled.

      &H1        CTS/RTS flow control enabled.

      &H2        XON/XOFF flow control enabled.

      &H3        CTS/RTS and XON/XOFF flow control enabled.

                             LOCK SERIAL PORT

  Type:          Configuration

  Format:        AT [cmds] &Bn [cmds]

  Description:   Sets operation of serial port speed.

    Command                              Function

      &B0        Serial speed follows connect speed.

      &B1        Serial speed locked.

      &B2        Serial speed locked in error correction mode only.

