
LASAT COMMUNICATIONS A/S

CREDIT 288

Card Type                    Modem (asynchronous)
Chipset                      Unidentified
Maximum Data Rate            28.8Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation              Bell 103A/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34

                             Rockwell V.FC
Fax Modulation               Unidentified
Error Correction/Compression MNP5, MNP10, V.42, V.42bis
Fax Class                    Class I & II
Data Bus                     PCMCIA Type II

                                                                      53856

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, comma, A/

  A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

  &C, &D, &F, &G, &K, &P, &R, &S, &T, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \G, \J, \K, \L, \N

  %C, %E, %L, %Q

                            Special AT Commands

  :E, *H, -K, )M, @M, +MS, -Q

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S24,
  S25, S26, S29, S30, S31

  S32, S33, S36, S38, S39, S46, S48, S82, S86, S91, S92, S95, S201

            Note: See MHI help file for complete information.

     UNIDENTIFIED COMMANDS

    Command         Default

      S14        Unidentified

      S21        Unidentified

      S22        Unidentified

      S23        Unidentified

      S27        Unidentified

      S28        Unidentified

      S37        Unidentified

      S40        Unidentified

      S41        Unidentified

                         Proprietary AT Command Set

                             AUTOSYNC OPTIONS

  Type:               Register

  Format              AT [cmds] S19=n [cmds]

  Default:            26

  Range:              0 - 30

  Description:        Controls autosync protocol, HDLC address detection,
                      bit coding, and HDLC idle.

   Bit       Value                         Function

    0             0   Not used

    1              0  Binary synchronous protocol used.

                  1   HDLC protocol used.

    2              0  HDLC address detect disabled.

                  1   HDLC address detect enabled.

    3              0  NRZI bit coding used.

                  1   NRZ bit coding used.

    4              0  HDLC idle sends MARK.

                  1   HDLC idle sends FLAG or SYNC.

                           AUTOSYNC HDLC ADDRESS

  Type:          Register

  Format:        AT [cmds] S20=n [cmds]

  Default:       0

  Range:         0-255

  Unit:          Unidentified

  Description:   Sets the HDLC address and binary synchronous character.

                               COUNTRY CODE

  Type:                  Configuration

  Format:                AT [cmds] *NCn [cmds]

  Description:           Sets the factory defaults according to the
                         country specified. The next power-up or ATZ
                         command will reset the modem to the appropriate
                         defaults.

                                   DIAL

  Type:                   Immediate

  Format:                 AT [cmds] D<#> [cmds]

  Description:            Dials the telephone number indicated according
                          to any modifiers included in the string.

        Command                              Function

           DJ             MNP10 link will be negotiated at 1200bps for
                          this call.

           DK             MNP10 power level adjustment enabled for this
                          call.

           DL             Re-dial last number.

           DP             Pulse dialing enabled.

          DS=n            Dial stored telephone number n.

           DT             Tone dialing enabled.

           DW             Dialing resumed following dial tone detection.

           D,             Dialing paused for amount of time specified in
                          S8 register.

           D!             Flash function initiated. Modem commanded to go
                          off-hook for specified time before returning
                          on-hook.

           D@             Wait for Quiet Answer function enabled. Modem
                          waits until a "quiet answer," a ring-back
                          signal followed by silence up to the time
                          specified in S7, is received prior to executing
                          the rest of the dial string.

           D^             Calling tone disabled for this call.

           D;             Modem returned to idle state after dialing. The
                          semicolon can only be placed at the end of the
                          dial command.

                         DISPLAY BLACKLIST NUMBERS

  Type:              Immediate

  Format:            AT [cmds] *B [cmds]

  Description:       Displays the list of all the numbers on the
                     blacklist and their statuses.

                          DISPLAY DELAYED NUMBERS

  Type:           Immediate

  Format:         AT [cmds] *D [cmds]

  Description:    Displays the list of all delayed numbers and their
                  statuses.

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Displays product identification code.

       I1        Displays ROM checksum.

       I2        Tests and reports ROM checksum.

       I3        Displays firmware revision.

       I5        Displays country code.

                          DISPLAY STORED NUMBERS

  Type:          Immediate

  Format:        AT [cmds] \F [cmds]

  Description:   Displays all stored telephone numbers.

                            PULSE DIALING MODE

  Type:          Configuration

  Format:        AT [cmds] *Zn [cmds]

  Description:   Selects the type of pulse dialing the modem will use.

    Command                              Function

      *Z0        Modem will use pulse dialing type 0.

      *Z1        Modem will use pulse dialing type 1.

