
ACER, INC.

MAGIC MP32

Card Type                           Modem, Fax, Sound card
Chip Set                            Unidentified
I/O Options                         CD-ROM interface, microphone, audio
                                    line in, audio line out, wavetable
                                    interface
Maximum Modem Rate                  33.6Kbps
Maximum Fax Rate                    14.4Kbps
Data Modulation Protocol            Bell 103/212A

                                    ITU-T V.22, V.22bis, V.23, V.32,
                                    V.32bis, V.34, V.34bis
Fax Modulation Protocol             ITU-T V.17, V.21CH2, V.27ter, V.29,
                                    V.33
Error Correction/Compression        MNP5, V.42, V.42bis
Fax Class                           Class I & II
Data Bus                            16-bit ISA
Card Size                           Full-length, full-height card

[Image]

                                CONNECTIONS

        Function           Label             Function              Label

  MIDI/Game port               CN1      Wave table interface        CN6

  Telephone line in            CN4      Speaker/Line out            CN7

  Telephone line out           CN5      Line in                     CN8

  Microphone in                CN9      CD-Audio                    JP5

                         SPEAKER/LINE OUT SETTINGS

            Function                      CN2                 CN3

  Speaker mode enabled (CN7)       Pins 1 & 2 closed   Pins 1 & 2 closed

  Line out function enabled        Pins 2 & 3 closed   Pins 2 & 3 closed























                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, A/

  A, B, C, D, E, H, M, O, P, Q, T, V, W, X, Y, Z

  &C, &F, &P, &Q, &R, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \K, \N, \V,

  %C, %E, %L, %Q, %TT

                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S24, S25,

  S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41,
  S46, S48, S82, S86, S91,

  S92, S95

                             Special Commands

  #CID, +MS, #BDR, #CLS, MDL?, #MFR?, #REV?, #TL, #VBQ?, #VBS, #VBT,
  #VCI?, #VLS, #VRA, #VRN,

  #VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX

  Note: See MHI Help File for full command documentation.

                         Proprietary AT Command Set

                            AUTO-MODE DETECTION

  Type:                  Configuration

  Format:                AT [cmds] Nn [cmds]

  Description:           Selects various options for the automatic
                         detection and negotiation of protocols during
                         the handshake process if the modem is
                         communicating with a remote modem of dissimilar
                         speed.

        Command                              Function

          N0             Auto-mode detection disabled

          N1             Auto-mode detection enabled

                    CLOCK SOURCE - SYNCHRONOUS TRANSMIT

  Type:          Configuration

  Format:        AT [cmds] &Xn [cmds]

  Description:   Selects DTE transmit clock source

    Command                              Function

      &X0        Modem generates clock

      &X1        Modem generates clock from the receive carrier signal

                            COMMUNICATIONS MODE

  Type:                 Configuration

  Format:               AT [cmds] &Mn [cmds]

  Description:          Selects communications mode

       Command                                Mode

         &M0            Asynchronous mode

         &M1            Synchronous connect mode and asynchronous
                        off-line command mode.

         &M2            Synchronous connect mode and asynchronous
                        off-line command mode and set DTR high.

         &M3            Synchronous connect mode and asynchronous
                        off-line command mode and set DTR to low.

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected

                         DATA TERMINAL READY (DTR)

  Type:               Configuration

  Format:             AT [cmds] &Dn [cmds]

  Description:        Selects modem response to DTR

            Note: The action each variant of &D causes depends on the
            setting of &Q

     &Q Setting          &D0           &D1          &D2           &D3

   &Q0, &Q5, &Q6      Command 0     Command 1    Command 2     Command 3

      &Q1, &Q4        Command 2     Command 1    Command 2     Command 3

      &Q2, &Q3        Command 2     Command 2    Command 2     Command 2

      Command                              Function

     Command 0        Modem does not respond to DTR

     Command 1        Modem goes to command mode after DTR goes is off

     Command 2        Modem goes to command mode and disconnects (hangs
                      up) after DTR goes off.

     Command 3        Modem is initialized after DTR goes off

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K3        RTS/CTS and DTE/DCE flow control enabled

      &K4        XON/XOFF and DTE/DCE flow control enabled

      &K5        Transparent XON/XOFF flow control enabled

      &K6        RTS/CTS and XON/XOFF flow control enabled

                                GUARD TONE

  Type:           Configuration

  Format:         AT [cmds] &Gn [cmds]

  Description:    Commands the modem to transmit a guard tone in
                  V.22/V.22bis

            Note: Used primarily for international data transmission

    Command                              Function

      &G0         Guard tone disabled

      &G1         Guard tone disabled

      &G2         1800Hz guard tone enabled











                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports modem model and speed

       I1        Reports ROM checksum

       I2        Reports OK

       I3        Reports firmware revision, model and interface type

       I4        Reports response programmed by OEM

       I5        Reports the country code parameter

       I6        Reports modem data pump model and code revision

                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Low volume setting

       L1        Low volume setting

       L2        Medium volume setting

       L3        Highest volume setting

                                TEST MODES

  Type:          Immediate

  Format:        AT [cmds] &Tn

  Description:   Selects test options

    Command                              Function

      &T0        End current test

      &T1        Begin local analog loopback test

      &T2        Returns error result code

      &T3        Begin local digital loopback

      &T4        Grant remote digital loopback request

      &T5        Deny remote digital loopback request

      &T6        Request remote digital loopback

      &T7        Request remote digital loopback and self-test

      &T8        Begin local analog loopback and self-test

                            S(status) -REGISTERS

                             AUTOSYNC OPTIONS

  Type:          Register

  Format         AT [cmds] S19=n

  Default:       0

  Description:   Enables selection of the autosync options





                       AUTOSYNC OR BSC SYNC ENABLED

  Type:          Register

  Format         AT [cmds] S20=n

  Default:       0

  Description:   Enables autosync HDLC address or BSC sync characters

