
MAXTECH CORPORATION

XPVS T2 (SF-1133HV/T2)

Card Type                      Modem (asynchronous)
Chip Set                       Unidentified
I/O Options                    Microphone, speaker out, line in, line out
Maximum Modem Rate             33.6Kbps
Maximum Fax Rate               14.4Kbps
Data Modulation Protocol       Bell 103/212A

                               ITU-T V.21, V.22, V.22bis, V.23, V.32,
                               V.32bis, V.34, V.34+, V.FC
Fax Modulation Protocol        ITU-T V.17, V.27ter, V.29
Error Correction/Compression   MNP5, V.42, V.42bis
Fax Class                      Class I
Data Bus                       8-bit ISA
Card Size                      Half-length, half-height card

[Image]

                                CONNECTIONS

        Function           Label             Function              Label

  Line out                      CN1      Microphone                 CN3

  Line in                       CN2      Speaker out                CN4

                        USER CONFIGURABLE SETTINGS

                      Setting                         Label      Position

  Speaker type stereo                                  JP5       Closed

  Speaker type mono                                    JP5        Open

                    SERIAL PORT ADDRESS

    Setting        JP3/A          JP3/B          JP3/C

  COM1 (3F8h)      Closed         Closed        Closed

  COM2 (2F8h)       Open          Closed        Closed

  COM3 (3E8h)      Closed          Open         Closed

  COM4 (2E8h)       Open           Open         Closed

      PnP           Open           Open          Open















                     INTERRUPT SELECTION

   IRQ      JP2/A     JP2/B      JP2/C     JP2/D     JP2/E

   2/9      Closed     Open      Open      Open      Open

    3        Open     Closed     Open      Open      Open

    4        Open      Open     Closed     Open      Open

    5        Open      Open      Open     Closed     Open

    7        Open      Open      Open      Open     Closed

   PnP       Open      Open      Open      Open      Open

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, +++, A/

  A, B, E, F, H, M, O, P, T, V, X

  &C, &G, &T, &W, &Z



                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S25



                              Voice Commands

  #BDR, #CLS, #MDL, #MFR, #VBQ?, #VBS, #VBT, #VBT, #VCI, #VLS, #VLS,
  #VRA, #VRA, #VRN, #VRN,

  #VRX, #VSD, #VSD, #VSK, #VSK, #VSP, #VSP, #VSR, #VSR, #VSS, #VSS, #VTD,
  #VTD, #VTS, #VTX

                         Proprietary AT Command Set

                            DISPLAY COMMAND SET

  Type:          Configuration

  Format:        AT [cmds] $ [cmds]

  Description:   Displays basic command set











                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DL             Re-dial last number

          DP             Pulse dialing enabled

          DR             Reverse dial mode

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D/             Delay 125 msec before dialing

          D$             Display dialing commands

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports modem model and speed

       I1        Reports ROM checksum

       I2        Tests and reports ROM checksum

       I3        Reports product ID

       I4        Reports current modem settings

       I5        Reports active and stored profiles

       I6        Reports link diagnostics

       I7        Product configuration

                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Low volume setting

       L1        Low volume setting

       L2        Medium volume setting

       L3        Highest volume setting

                               RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] Qn [cmds]

  Description:   Enables modem to send result codes to the DTE

    Command                              Function

       Q0        Modem sends responses

       Q1        Modem does not send responses

       Q2        Displays result codes only in Originate Mode

                           LONG SPACE DISCONNECT

  Type:             Configuration

  Format:           AT [cmds] Yn [cmds]

  Description:      Commands the modem to disconnect after a 1.6 second
                    break is detected

     Command                              Function

        Y0          Configuration profile 0 active upon power on or reset

        Y1          Configuration profile 1 active upon power on or reset

        Y2          Factory configuration 0 active upon power on or reset

        Y3          Factory configuration 1 active upon power on or reset

        Y4          Factory configuration 2 active upon power on or reset

        Y6          Reports link diagnostics

                                SOFT RESET

  Type:                Immediate

  Format:              AT [cmds] Zn [cmds]

  Description:         Restores modem profiles previously saved in
                       non-volatile RAM using the &W command.

       Command                              Function

          Z0           Reset and retrieve active profiles set by the Y
                       command

          Z1           Reset and retrieve active profile 0

          Z2           Reset and retrieve active profile 1

          Z3           Reset and retrieve factory default profile 0

          Z4           Reset and retrieve factory default profile 1

          Z5           Reset and retrieve factory default profile 2

                             ARQ RESULT CODES

  Type:               Configuration

  Format:             AT [cmds] &An [cmds]

  Description:        Selects ARQ result code settings

      Command                              Function

        &A0           Disable ARQ result codes

        &A1           Enable ARQ result codes

        &A2           Disable ARQ result codes and V.32 modulation

        &A3           Enable ARQ result codes and error correction and
                      data compression protocols









                                 DTE RATE

  Type:          Configuration

  Format:        AT [cmds] &Bn [cmds]

  Description:   Controls DTE rate

    Command                              Function

      &B0        DTE rate adjust to DCE rate after on-line

      &B1        Constant DTE rate

      &B2        Constant DTE rate in ARQ mode, variable in non-ARQ mode

                                     DATA TERMINAL READY (DTR)

  Type:               Configuration

  Format:             AT [cmds] &Dn [cmds]

  Description:        Selects modem response to DTR

            Note: The action each variant of &D causes depends on the setting of &Q

      Command                                          Function

        &D0           Modem does not respond to DTR

        &D1           Modem goes to command mode after DTR goes is off

        &D2           Modem hands up and returns to the command mode after DTR toggle

                          FACTORY DEFAULT PROFILE

  Type:               Configuration

  Format:             AT [cmds] &F [cmds]

  Description:        Sets values in active profile to values found in
                      the default profile

            Note: Used primarily for international data transmission

       Command                             Function

         &F0          Recall factory default configuration 0

         &F1          Recall factory default configuration profile 1
                      (hardware flow control enabled)

         &F2          Recall factory default configuration profile 2
                      (software flow control enabled)

                                  TX FLOW

  Type:           Configuration

  Format:         AT [cmds] &Hn [cmds]

  Description:    Controls TX flow settings

            Note: Used primarily for international data transmission

    Command                              Function

      &H0         Disable TX flow control

      &H1         Enable hardware TX flow control (CTS)

      &H2         Enable software TX flow control (XON/XOFF)

      &H3         Enable hardware (CTS) and software (XON/XOFF) TX flow
                  control

















                                  RX FLOW

  Type:                  Configuration

  Format:                AT [cmds] &In [cmds]

  Description:           Controls RX flow settings

            Note: Used primarily for international data transmission

        Command                              Function

          &I0            Disable software RX flow control

          &I1            Enable software RX flow control (XON/XOFF)

          &I2            Enable software RX flow control (XON/XOFF), but
                         do not pass XON/XOFF to remote modem or local
                         DTE

          &I3            Enable HP ENQ/ACK software flow control, host
                         mode

          &I4            Enable HP ENQ/ACK software flow control,
                         terminal mode

          &I5            Enable software RX flow control (XON/XOFF) for
                         non-ARQ mode

                            COMPRESSION CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables compression control options

    Command                              Function

      &K0        Disable V.42bis/MNP5 data compression

      &K1        Auto data compression

      &K2        Enable V.42bis/MNP5 data compression

      &K3        Disable MNP5 data compression

                            COMMUNICATIONS MODE

  Type:          Configuration

  Format:        AT [cmds] &Mn [cmds]

  Description:   Selects communications mode

    Command                                Mode

      &M0        Normal mode enabled

      &M4        ARQ and Normal modes enabled

      &M5        ARQ mode enabled

































                         AUTOMODE CONNECTION SPEED

  Type:          Configuration

  Format:        AT [cmds] &Nn [cmds]

  Description:   Selects connection speed

    Command                                Mode

      &N0        Enable Automode

      &N1        Set connection speed to 300bps

      &N2        Set connection speed to 1200bps

      &N3        Set connection speed to 2400bps

      &N4        Set connection speed to 4800bps

      &N5        Set connection speed to 7200bps

      &N6        Set connection speed to 9600bps

      &N7        Set connection speed to 12000bps

      &N8        Set connection speed to 14400bps

      &N9        Set connection speed to 16800bps

      &N10       Set connection speed to 19200bps

      &N11       Set connection speed to 21600bps

      &N12       Set connection speed to 24400bps

      &N13       Set connection speed to 26400bps

      &N14       Set connection speed to 28800bps

      &N15       Set connection speed to 31200bps

      &N16       Set connection speed to 33600bps

                            PULSE DIALING RATIO

  Type:          Configuration

  Format:        AT [cmds] &Pn [cmds]

  Description:   Selects pulse dial make/break ratio

    Command                              Function

      &P0        39/61ms at 10pps (North America)

      &P1        33/67ms at 10pps (Europe)

                                  RTS/CTS

  Type:          Configuration

  Format:        AT [cmds] &Rn [cmds]

  Description:   Selects RTS/CTS options

    Command                              Function

      &R0        Reserved

      &R1        Modem ignores the RTS signal

      &R2        Enable RX hardware flow control (RTS)

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR off in command mode, on in on-line mode

                       MINIMUM DCE CONNECTION SPEED

  Type:          Immediate

  Format:        AT [cmds] &Un

  Description:   Selects test options

    Command                              Function

      &U0        Do not set minimum DCE connection speed

      &U1        Set connection speed to 300bps

      &U2        Set connection speed to 1200bps

      &U3        Set connection speed to 2400bps

      &U4        Set connection speed to 4800bps

      &U5        Set connection speed to 7200bps

      &U6        Set connection speed to 9600bps

      &U7        Set connection speed to 12000bps

      &U8        Set connection speed to 14400bps

      &U9        Set connection speed to 16800bps

      &U10       Set connection speed to 19200bps

      &U11       Set connection speed to 21600bps

      &U12       Set connection speed to 24400bps

      &U13       Set connection speed to 26400bps

      &U14       Set connection speed to 28800bps

      &U15       Set connection speed to 31200bps

      &U16       Set connection speed to 33600bps

                               BREAK CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Yn [cmds]

  Description:   Controls break

    Command                              Function

      &Y0        Destructive break. Does not send break

      &Y1        Destructive break. Break expedited

      &Y2        Nondestructive break. Break expedited

                            S(status) -REGISTERS

                          BIT-MAPPED REGISTER S13

  Type:             Register

  Format            AT [cmds] S13=n [cmds]

  Unit:             Bit-mapped

  Description:      DTR reset, ARQ 1.5K buffer DTR/reset, backspace
                    autodial, +++ hangup

                          BIT-MAPPED REGISTER S15

  Type:          Register

  Format         AT [cmds] S15=n [cmds]

  Unit:          Bit-mapped

  Description:   Disable V.42bis/MNP MNP incompatability





                             INACTIVITY TIMER

  Type:             Register

  Format            AT [cmds] S19=n [cmds]

  Default:          0

  Range:            0-255

  Unit:             1 minute

  Description:      Sets the length of time inactivity timer waits before
                    disconnecting

                               BREAK LENGTH

  Type:          Register

  Format         AT [cmds] S21=n [cmds]

  Default:       10

  Range:         0-255

  Unit:          .01 second

  Description:   ARQ break length

                       FLOW CONTROL CHARACTER - XON

  Type:          Register

  Format:        AT [cmds] S22=n [cmds]

  Default:       17

  Range:         0-127

  Unit:          ASCII

  Description:   Sets the character used to represent XON

                       FLOW CONTROL CHARACTER - XOFF

  Type:          Register

  Format:        AT [cmds] S23=n [cmds]

  Default:       19

  Range:         0-127

  Unit:          ASCII

  Description:   Sets the character used to represent XOFF

                          BIT-MAPPED REGISTER S27

  Format                 AT [cmds] S27=n [cmds]

  Default:               Unidentified

  Unit:                  Bit-mapped

  Description:           V.21 @ 300bps, non-trellis encoding, disable
                         2400 Hz answer tone, 9600 result codes, disable
                         V.32bis, enable V.23

                          BIT-MAPPED REGISTER S28

  Format         AT [cmds] S28=n [cmds]

  Default:       8

  Range:         0-255

  Unit:          0.1 second

  Description:   Controls V.32 handshake length





                             ANSWER MODE TIMER

  Type:          Register

  Format         AT [cmds] S29=n [cmds]

  Default:       20

  Range:         0-255

  Unit:          .01 second

  Description:   V.21 answer mode timer

                          BIT-MAPPED REGISTER S32

  Type:          Register

  Format:        AT [cmds] S32=n [cmds]

  Unit:          Bit-mapped

  Description:   Disable V.FC, V.34, V.34bis, Enable V.8

                          BIT-MAPPED REGISTER S33

  Type:                Register

  Format:              AT [cmds] S33=n [cmds]

  Unit:                Bit-mapped

  Description:         Disable 2400, 2743, 2800, 3000, 3200, and 3429
                       symbol rates, call indicate, V.8

                          BIT-MAPPED REGISTER S34

  Type:          Register

  Format:        AT [cmds] S34=n [cmds]

  Unit:          Bit-mapped

  Description:   Disable 8S-2D, 16S-4D, 32S-4D maps

