
MAXTECH CORPORATION

XPV 336I (VF-1133HV/R9)

Card Type                    Modem/Fax card
Chip Set                     Unidentified
I/O Options                  Line in(RJ-11), line out(RJ-11)
Maximum Modem Rate           33.6Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Bell 103/212A

                             ITU-T V34, V.32bis, V.32, V.23, V.22bis,
                             V.22, V.21, V.FC
Fax Modulation Protocol      ITU-T V.17, V.27ter, V.29, V.21
Error Correction/Compression MNP5, V.42, V.42bis
Fax Class                    Class I & II
Data Bus                     8-bit ISA

[Image]

                                CONNECTIONS

         Function             Label             Function            Label

 RJ-11 line                        CN1        RJ-11 line             CN2

                            SERIAL PORT ADDRESS

      Setting             JP6/A             JP6/B             JP6/C

    COM1 (3F8h)           Open             Closed             Closed

    COM2 (2F8h)           Open              Open              Closed

    COM3 (3E8h)           Open             Closed              Open

    COM4 (2E8h)           Open              Open               Open

  Plug & Play           Closed             Open               Open
 enabled

                                 INTERRUPT

     Setting          JP6/D         JP6/E         JP6/F         JP6/G

     IR/FONT>        Closed         Open          Open           Open

       IRQ3           Open         Closed         Open           Open

       IRQ4           Open          Open         Closed          Open

       IRQ5           Open          Open          Open          Closed

  Plug & Play        Open         Closed         Open           Open
 enabled

                           SUPPORTED COMMAND SET

                             Basic AT Commands

 AT, +++, A/

 A, E, H, M, O, P, T, V, X, Y, Z

 &C, &G, &L, &T, &V, &W, &Y, &Z

                           Extended AT Commands

 \A, \B, \C, \E, \G, \J, \K, \O, \Q, \U, \X, \Y, \Z

 %A

                                S Registers

 S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
 S21, S22

 S23, S25, S26, S27, S28

                            Voice Mode Commands

 #BDR, #CLS, #MDL?, #MFR?, #REV?, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA,
 #VRN, #VRX, #VSD

 #VSK, #VSP, #VSR, #VSS, #VTD, #VTS, #VTX

 Note: See MHI Help File for full command documentation.

                         PROPRIETARY AT COMMAND SET

                         AUTO-FALLFORWARD/FALLBACK

 Type:           Configuration

 Format:         AT [cmds] &En [cmds]

 Description:    Enables/disables auto fallforward/fallback

    Command                              Function

  &E0           Auto fallforward/fallback disabled

      &E1        Auto fallforward/fallback enabled

                          COMMUNICATION PROTOCOLS

 Type:                  Configuration

 Format:                AT [cmds] Bn [cmds]

 Description:           Selects the communication protocol for data calls

           Note: The B command allows the simultaneous selection of more
           than one suffix, enabling multiple protocols.

        Command                              Protocol

          B0            CCITT mode

  B1                   Bell 212A at 300 or 1200bps

          B2            Autoscan mode

          B3            CCITT V.23 mode

          B4            300bps

          B5            1200bps

          B6            2400bps

          B7            4800bps

          B8            9600bps

          B9            14400bps

          B10           16800bps

          B11           19200bps

          B12           21600bps

          B13           28800bps

          B14           31200bps

          B15           33600bps

                            COMMUNICATIONS MODE

 Type:           Configuration

 Format:         AT [cmds] &Mn [cmds]

 Description:    Selects communications mode

    Command                                Mode

      &M0        Asynchronous mode

                           DATA SET READY (DSR)

 Type:           Configuration

 Format:         AT [cmds] &Sn [cmds]

 Description:    Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected

                         DATA TERMINAL READY (DTR)

 Type:           Configuration

 Format:         AT [cmds] &Dn [cmds]

 Description:    Selects modem response to DTR

    Command                              Function

      &D0        DTR override

      &D1        DTR toggle causes online command mode

      &D2        Normal DTR operations

      &D3        Resets on receipt of DTR

                                   DIAL

 Type:                  Immediate

 Format:                AT [cmds] D<#> [cmds]

 Description:           Dials telephone number according to any modifiers
                        included in the string

 Note:                  Any combination of modifiers can be used to
                        produce the desired dial functions in sequence.

        Command                              Function

          DP            Pulse dialing enabled

          DR            Answer mode enabled; originate mode disabled
                        following handshake initiation.

         DS=n           Dial stored telephone number n

          DT            Tone dialing enabled/Pulse dialing disabled

          DW            Dialing resumed following dial tone detection

          D,            Dialing paused for amount of time specified in S8
                        register

          D!            Flash function initiated. Modem commanded to go
                        off-hook for specified time before returning
                        on-hook.

          D@            Wait for Quite Answer function enabled. Modem
                        waits until a "quiet answer," a ring-back signal
                        followed by silence up to the time specified in
                        S7, is received prior to executing the rest of
                        the dial string.

          D;            Modem returned to idle state after dialing. The
                        semicolon can only be placed at the end of the
                        dial command.

                          FACTORY DEFAULT PROFILE

 Type:                Configuration

 Format:              AT [cmds] &F [cmds]

 Description:         Sets values in active profile to values found in
                      the default profile

       Command                             Function

         &F0          Factory default profile with V.42bis/hardware flow
                      control enabled

         &F1          Factory default profile with software flow control
                      enabled

         &F2          Factory default profile with V.42bis/hardware flow
                      control enabled

         &F3          Factory default profile with software flow control
                      enabled (Macintosh)

         &F4          Factory default profile with V.42bis/hardware flow
                      control enabled (Macintosh)

         &F5          Factory default profile with V.42bis/hardware flow
                      control disabled

                                HELP SCREEN

 Type:           Configuration

 Format:         AT [cmds] &H [cmds]

 Description:    Displays help screen

                              ORIGINATE MODE

 Type:           Configuration

 Format:         AT [cmds] &On [cmds]

 Description:    Enables/disables originate-only mode

    Command                             Line Type

      &O0        Originate-only mode disabled

      &O1        Originate-only mode enabled

                            PULSE DIALING RATIO

 Type:           Configuration

 Format:         AT [cmds] &Pn [cmds]

 Description:    Selects pulse dial make/break ratio

    Command                              Function

      &P0        39/61ms at 10pps (North America)

      &P1        33/67ms at 10pps (Europe)

                            REPORT INFORMATION

 Type:           Immediate

 Format:         AT [cmds] In [cmds]

 Description:    Displays information requested

    Command                              Function

      I0         Reports four digit product code

      I1         Reports ROM checksum

      I2         Reports internal memory test

      I3         V.42bis ID

      I4         Reports internal ID

                               RESULT CODES

 Type:           Configuration

 Format:         AT [cmds] Qn [cmds]

 Description:    Enables modem to send result codes to the DTE

    Command                              Function

  Q0            Result code sending enabled

      Q1         Result code sending disabled

      Q2         Result code sending disabled in answer mode

                              SPEAKER VOLUME

 Type:           Configuration

 Format:         AT [cmds] Ln [cmds]

 Description:    Controls speaker volume

    Command                              Function

      L0         Low volume setting

      L1         Low volume setting

  L2            Medium volume setting

      L3         Highest volume setting

                          EXTENDED AT COMMAND SET

                          AUTODETECT V.34 & V.FC

 Type:           Configuration

 Format:         AT [cmds] %Mn [cmds]

 Description:    Controls autodetect for V.34 and V.FC negotiation
                 signals

    Command                              Function

      %M0        V.34 and V.FC autodetect enabled

      %M1        V.34 autodetect enabled

      %M2        V.FC autodetect enabled

                 AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

 Type:           Configuration

 Format:         AT [cmds] %En [cmds]

 Description:    Controls auto-retrain mode and fallback/fall-forward

    Command                              Function

      %E0        Auto-retrain disabled

      %E1        Auto-retrain enabled

                            CALL-BACK SECURITY

 Type:           Configuration

 Format:         AT [cmds] %Sn [cmds]

 Description:    Selects call-back security password options

    Command                              Function

      %S0        Call-back security disabled

      %S1        Password check only enabled

      %S2        Call-back security with password check enabled

                             CLEAR-DOWN SIGNAL

 Type:           Configuration

 Format:         AT [cmds] %Dn [cmds]

 Description:    Enables/disables clear-down signal

    Command                              Function

      %D0        Clear-down signal disabled

      %D1        Clear-down signal enabled

                                COMPRESSION

 Type:           Configuration

 Format:         AT [cmds] %Cn [cmds]

 Description:    Selects data compression

    Command                              Function

      %C0        Data compression disabled

      %C1        MNP5 enabled

                               CONNECT MODE

 Type:           Configuration

 Format:         AT [cmds] \Nn [cmds]

 Description:    Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        MNP mode enabled

      \N3        MNP or Normal mode enabled

      \N4        V.42 mode enabled

      \N5        V.42 or MNP reliable mode enabled

      \N6        V.42/MNP/Normal mode enabled

                           EXTENDED RESULT CODES

 Type:           Configuration

 Format:         AT [cmds] \Vn [cmds]

 Description:    Selects extended result codes

    Command                              Function

      \V0        Reports DCE speed; extended result codes disabled

  \V1           Reports DCE speed; extended result codes enabled

      \V2        Reports DTE speed; extended result codes disabled

      \V3        Reports DTE speed; extended result codes enabled

                             INACTIVITY TIMER

 Type:                   Configuration

 Format:                 AT [cmds] \Tn [cmds]

 Range:                  0-90

 Unit:                   1 second

 Description:            Sets the length of time that the modem does not
                         receive information before it disconnects.

                             LINE SIGNAL LEVEL

 Type:           Immediate

 Format:         AT [cmds] %L [cmds]

 Range:          0-15

 Unit:           -1 dBm

 Description:    Sets transmit level. Default=12

                           POWER-ON AUTO-CONNECT

 Type:           Configuration

 Format:         AT [cmds] %Pn [cmds]

 Description:    Enables/disables power-on auto-connect

    Command                              Function

      %P0        Power-on auto-connect disabled

      %P1        Power-on auto-connect enabled

                              STORED PASSWORD

 Type:                   Configuration

 Format:                 AT [cmds] \P=n [cmds]

 Range:                  0-127

 Unit:                   ASCII

 Description:            Stores password with a maximum of seven
                         characters in NVRAM. \P=? displays stored
                         password



