
MAXTECH CORPORATION

XPVS288R9 (SF-1128HV/R9)

Card Type                    Modem, Fax
Chip Set                     Unidentified
I/O Options                  Line in, line out, microphone in, speaker out
Maximum Modem Rate           28.8Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34
Fax Modulation Protocol      ITU-T V.17, V.27ter, V.29
Error Correction/Compression MNP5, V.42, V.42bis
Fax Class                    Class I & II
Data Bus                     16-bit ISA
Card Size                    Half-length, full-height card

[Image]

                                CONNECTIONS

        Function           Label             Function              Label

  Line out                      CN1      Microphone in              CN3

  Line in                       CN2      Speaker out                CN4

                        USER CONFIGURABLE SETTINGS

                Setting                      Label          Position

  Microphone set for dynamic                  JP2       Pins 1 & 2 closed

  Microphone set for condenser                JP2       Pins 2 & 3 closed

  Speaker set for stereo                      JP4            Closed

  Speaker set for mono                        JP4             Open

  Plug and Play enabled                      PNP1            Closed

  Plug and Play disabled                     PNP1             Open

                    SERIAL PORT ADDRESS

    Setting         PNP1          SW1/1          SW1/2

  COM1 (3F8h)       Open            On            On

  COM2 (2F8h)       Open           Off            On

  COM3 (3E8h)       Open            On            Off

  COM4 (2E8h)       Open           Off            Off

      PnP         Closed          Off            Off

                           IRQ SETTINGS

   Setting         PNP1       SW1/3     SW1/4     SW1/5     SW1/6

     2/9           Open         On       Off       Off      Off

      3            Open        Off        On       Off      Off

      4            Open        Off       Off        On      Off

      5            Open        Off       Off       Off       On

     PnP         Closed       Off       Off       Off      Off

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, +++, A/

  A, E, H, M, O, P, T, V, X, Y, Z

  &C, &G, &L, &T, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \C, \E, \G, \J, \K, \O, \Q, \U, \X, \Y, \Z

  %A

                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S25, S26,

  S27

                             Special Commands

  #BDR, #CLS, #MDL?, #MFR?, #REV?, #SPK=a,b,c, #VBQ?, #VBS, #VBT, #VCI?,
  #VLS, #VRA, #VRN,

  #VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTS, #VTX

  Note: See MHI Help File for full command documentation.

                         Proprietary AT Command Set

                            COMMUNICATIONS MODE

  Type:          Configuration

  Format:        AT [cmds] &Mn [cmds]

  Description:   Selects communications mode

    Command                                Mode

      &M0        Asynchronous mode

                          COMMUNICATION PROTOCOLS

  Type:                  Configuration

  Format:                AT [cmds] Bn [cmds]

  Description:           Selects the communication protocol for data
                         calls

            Note: The B command allows the simultaneous selection of more
            than one suffix, enabling multiple protocols.

        Command                              Protocol

          B0             Enables CCITT mode

          B1             Enables Bell mode

          B2             Enables Autoscan mode

          B3             Enables CCITT V.23 mode only

          B4             Enables 300 bps connection only

          B5             Enables 1200 bps connection only

          B6             Enables 2400 bps connection only

          B7             Enables 4800 bps connection only

          B8             Enables 9600 bps connection only

          B9             Enables 14400 bps connection only

          B10            Enables 16800 bps connection only

          B11            Enables 19200 bps connection only

          B12            Enables 21600 bps connection only

          B13            Enables 24000 bps connection only

          B14            Enables 26400 bps connection only

          B15            Enables 28800 bps connection only

                         DATA TERMINAL READY (DTR)

  Type:                  Configuration

  Format:                AT [cmds] &Dn [cmds]

  Description:           Selects modem response to DTR

        Command                              Function

       Command 0         Modem does not respond to DTR

       Command 1         Modem goes to command mode after DTR goes is off

       Command 2         Modem goes to command mode and disconnects
                         (hangs up) after DTR goes off; Auto-Answer is
                         disabled.

       Command 3         Modem is initialized after DTR goes off

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DP             Pulse dialing enabled

          DR             Answer mode enabled; originate mode disabled
                         following handshake initiation.

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected

                              FACTORY DEFAULT

  Type:                  Configuration

  Format:                AT [cmds] &Fn [cmds]

  Description:           Recalls factory default configuration and/or
                         with software flow control enabled

        Command                              Function

          &F0           Recalls factory default configuration

          &F1            Recalls factory default configuration with
                         software flow control enabled

          &F2            Recalls factory default configuration with
                         hardware flow control enabled

          &F3            Recalls factory default configuration with
                         software flow control enabled and ignores the
                         DTR signal

          &F4            Recalls factory default configuration with
                         hardware flow control enabled and ignores the
                         DTR signal

          &F5            Set modem to Direct mode

                          FALL FORWARD/FALL BACK

  Type:          Configuration

  Format:        AT [cmds] &En [cmds]

  Description:   Enables/Disables fall forward/fall back

    Command                              Function

      &E0       Disables automatic fall forward/fall back

      &E1        Enables automatic fall forward/fallback

                                   HELP

  Type:          Configuration

  Format:        AT [cmds] &H [cmds]

  Description:   Displays the modem help screen

                              ORIGINATE MODE

  Type:          Configuration

  Format:        AT [cmds] &On [cmds]

  Description:   Enables/Disables originate-only mode

    Command                                Mode

      &O0        Originate-only mode disabled

      &O1        Originate-only mode enabled

                            PULSE DIALING RATIO

  Type:          Configuration

  Format:        AT [cmds] &Pn [cmds]

  Description:   Selects pulse dial make/break ratio

    Command                              Function

      &P0        39/61ms at 10pps (North America)

      &P1        33/67ms at 10pps (Europe & Hong Kong)

                            REPORT INFORMATION

  Type:              Immediate

  Format:            AT [cmds] In [cmds]

  Description:       Displays information requested and configures Plug
                     and Play serial number

      Command                              Function

        I0           Reports product ID

        I1           Reports ROM checksum

        I2           Tests and reports internal memory

        I3           Reports V.42bis ID

        I4           Reports internal ID

       I99=n         Configures Plug and Play serial number to n (n =
                     0-225)

                               RESULT CODES

  Type:           Configuration

  Format:         AT [cmds] Qn [cmds]

  Description:    Enables modem to send result codes to the DTE

    Command                              Function

       Q0         Result code sending enabled

       Q1         Result code sending disabled

       Q2         Result code sending disabled only when answer mode is
                  enabled

                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Low volume setting

       L1        Low volume setting

       L2        Medium volume setting

       L3        Highest volume setting

                          Extended AT Command Set

                 AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

  Type:          Configuration

  Format:        AT [cmds] %En [cmds]

  Description:   Controls auto-retrain mode and fallback/fall-forward

    Command                              Function

      %E0        Auto-retrain disabled

      %E1       Auto-retrain enabled

                           AUTO-DETECT SETTINGS

  Type:          Configuration

  Format:        AT [cmds] %Mn [cmds]

  Description:   Controls V.34 and V.FC while in auto-detect mode

    Command                              Function

      %M0       Sets V.34 and V.FC to auto-detect mode

      %M1        Sets only V.34 to auto-detect

      %M2        Sets only V.FC to auto-detect

                             CLEAR-DOWN SIGNAL

  Type:          Configuration

  Format:        AT [cmds] %Dn [cmds]

  Description:   Enables/Disables clear-down signal

    Command                              Function

      %D0        Clear-down signal disabled

      %D1       Clear-down signal enabled

                          COMPRESSION/CORRECTION

  Type:           Configuration

  Format:         AT [cmds] %Cn [cmds]

  Description:    Selects data compression and correction

    Command                              Function

      %C0         Data compression and correction disabled

      %C1         MNP5 and V.42bis; or data compression and correction
                  enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        MNP reliable mode enabled

      \N3        Auto-reliable mode or MNP auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

      \N5        V.42 auto-reliable mode or MNP auto-reliable mode
                 enabled

      \N6        V.42/MNP/Normal data link enabled

                                    DCE

  Type:          Configuration

  Format:        AT [cmds] \Vn [cmds]

  Description:   Reports DCE speed and extended responses

    Command                              Function

      \V0       Reports DCE speed without sending extended responses

      \V1        Reports DCE speed and send sends extended responses

      \V2        Reports DTE speed without sending extended responses

      \V3        Reports DTE speed and send sends extended responses

                             INACTIVITY TIMER

  Type:                  Configuration

  Format:                AT [cmds] \Tn [cmds]

  Default:               0

  Range:                 0-90

  Unit:                  1 minute

  Description:           Sets the length of time that the modem does not
                         receive information before it disconnects.

                             LINE SIGNAL LEVEL

  Type:           Immediate

  Format:         AT [cmds] %Ln [cmds]

  Default:        11

  Range:          0-15

  Unit:           dBm

  Description:    Returns a value which indicates the received line
                  signal level

                                 PASSWORD

  Type:                  Configuration

  Format:                AT [cmds] \P=x [cmds]

  Description:           Stores password x (x=ASCII characters 1 through
                         127 excluding "?" maximum 7 characters) stored
                         into non-volatile RAM

                           POWER-ON AUTO-CONNECT

  Type:          Configuration

  Format:        AT [cmds] %Pn [cmds]

  Description:   Enables/Disables power-on auto-connect

    Command                              Function

      %P0       Power-on auto-connect disabled

      %P1        Power-on auto-connect enabled

                                 SECURITY

  Type:          Configuration

  Format:        AT [cmds] %Sn [cmds]

  Description:   Enables/Disables call-back security and checks password

    Command                              Function

      %S0       Call-back security disabled

      %S1        Password check enabled

      %S2        Call-back security and password check enabled

                            S(status) -Registers

                          BIT-MAPPED REGISTER S28

  Type:                  Register

  Format                 AT [cmds] S28=n [cmds]

  Unit:                  Bit-mapped

  Description:           Configures Power-on auto-connect, security
                         call-back, auto-retrain, and Bell/CCITT mode
                         settings

