
RAD DATA COMMUNICATIONS

FCD-E1/1

Card Type                  E1 CSU/DSU
Chip Set                   Unidentified
I/O Options                AC power connector, 25-pin port (RS-530), BNC
                           connectors (2),

                           9-pin serial ports (2 RS-232), E1 network
                           interface via RJ-45 connector
E1 Transfer Rate           2.048Kbps
E1 Protocol                HDB3
Frame type                 CRC-4
Data Bus                   External

[Image]

                                CONNECTIONS

          Function            Label            Function            Label

  AC power connector           CN1     Header connector to CH2      CN8
                                       interface board

  DTE serial port              CN2     Header connector to CH2      CN9
                                       interface board

  25-pin connector -           CN3     DCE serial port              CN10
  channel 1

  Network port via RJ-48       CN4     Power switch                 SW2
  connector

  Header connector to sub      CN5     BNC connector - receive       RX
  interface board

  Header connector to CH2      CN6     BNC connector - transmit      TX
  interface board

  Header connector to CH2      CN7
  interface board

                        USER CONFIGURABLE SETTINGS

                  Setting                      Label         Position

     Signal ground is connected to the         JP8           Closed
      frame ground

      Signal ground is not connected to         JP8            Open
      the frame ground

     Transmit side ground reference set        JP9            Open
      for balanced interface

      Transmit side ground reference set        JP9           Closed
      for unbalanced interface

     Receive side ground reference set        JP10            Open
      for balanced interface

      Receive side ground reference set        JP10           Closed
      for unbalanced interface

     Front panel push-buttons enabled         JP77            Open

      Front panel push-buttons disabled        JP77           Closed

     Supervisor ports operate according       S1/1             Off
      to user-defined parameters

      CSU/DSU uses default parameters          S1/1             On
      stored in its EPROM

     Default password enabled.                S1/2             On
      Password=RAD

      User password enabled                    S1/2             Off

     Loads user-selected parameters from      S1/3             Off
      NVRAM on power-up

      Loads default parameters stored in       S1/3             On
      its EPROM on power-up

     Factory configured - do not alter        S1/4             Off

                            MAIN LINK INTERFACE

    Function       JP7     JP12/A   JP12/B   JP12/C   JP12/D   JP33   JP35

      Balanced    Open     Open    Closed    Open    Open     2 &    2 &
      interface                                                 3      3

      Unbalanced  Closed    Open     Open     Open    Closed   1 &    1 &
      interface                                                 2      2

  Note: Pins designated are in the closed position

                                ALARM RELAY

                    Function                         JP51         JP52

      Alarm relay disconnected. DTE port (CN2)      2 & 3        2 & 3
             provides full functionality

       Alarm relay connected instead of DCD and      1 & 2        1 & 2
                      CTS lines

  Note: Pins designated are in the closed position

                             DIAGNOSTIC LED(S)

   LED          Color          Status               Condition

   LOC1      Unidentified        On        Local synchronization lost on
                                                    main link

   LOC1      Unidentified       Off      Local synchronization OK on main
                                                       link

   REM1      Unidentified        On       Remote synchronization lost on
                                                    main link

   REM1      Unidentified       Off        Remote synchronization OK on
                                                    main link

   LOC2      Unidentified        On        Local synchronization lost on
                                                     sub link

   LOC2      Unidentified       Off       Local synchronization OK on sub
                                                       link

   REM2      Unidentified        On       Remote synchronization lost on
                                                     sub link

   REM2      Unidentified       Off      Remote synchronization OK on sub
                                                       link

   ALM       Unidentified        On         Alarm condition detected on
                                                     network

   ALM       Unidentified       Off       Alarm condition not detected on
                                                     network

            TUnidentified        On        Device loopback test active

   TST       Unidentified       Off      Device loopback test not running

[Image]

VER. X.21

                CONNECTIONS

            Function              Label

  15-pin connector - channel 1     CN11

[Image]

VER. V.35

                CONNECTIONS

            Function              Label

  34-pin connector - channel 1     CN12

                       MISCELLANEOUS TECHNICAL NOTE

  CN11 and CN12 are modules which can be used to replace CN3, allowing
  for various DTE/DCE interfaces.

