
SHARK MULTIMEDIA

BASKING COMBO

Card Type                         Modem (asynchronous), Sound card
Chip Set                          Unidentified
I/O Options                       Line in, microphone, speaker out,
                                  game/MIDI port
Maximum Modem Rate                56Kbps
Maximum Fax Rate                  14.4Kbps
Data Modulation Protocol          Bell 103/212A

                                  ITU-T V.21, V.22A/B, V.22bis, V.23, V.32,
                                  V.32bis, V.34, V.FC, K56flex
Fax Modulation Protocol           ITU-T V.17, V.29, V.27ter, V.33, V.21CH2
Error Correction/Compression      MNP5, MNP10, V.42, V.42bis
Fax Class                         Class I
Data Bus                          16-bit ISA
Card Size                         Half-length, half-height card

[Image]

                                CONNECTIONS

        Function           Label             Function              Label

  Line in                       CN1      Microphone                 CN4

  Line out                      CN2      Speaker out                CN5

  Line in                       CN3      Game/MIDI port             CN6

                       SUPPORTED COMMAND SET

                         Basic AT Commands

  AT, +++, A/

  A, E, H, M, O, P, Q, T, V, X

  &C, &P, &R, &V, &W, &Z

                       Extended AT Commands

  \A, \B, \K, \N

  %C, %E

                          Voice Commands

  #BDR, #CID, #TL, #VBS, #VSD, #VGT

                            S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S18, S25, S26

                         Special Commands

  +MS

  Note: See MHI Help File for full command documentation.







                         Proprietary AT Command Set

                             AUTOMODE CONTROL

  Type:          Immediate

  Format:        AT [cmds] Nn [cmds]

  Description:   Controls the automode detection

    Command                              Function

       N0        Disabled

       N1        Enabled

                          COMMUNICATION PROTOCOLS

  Type:                  Configuration

  Format:                AT [cmds] Bn [cmds]

  Description:           Selects the communication protocol for data
                         calls

            Note: The B command allows the simultaneous selection of more
            than one suffix, enabling multiple protocols.

        Command                              Protocol

          B0             ITU-T V.22 at 300 or 1200bps

                                COMPRESSION

  Type:           Configuration

  Format:         AT [cmds] &Kn [cmds]

  Description:    Selects data compression

    Command                              Function

      &K0         Data compression disabled

      &K1         MNP5 enabled

      &K2         V.42bis enabled

      &K3         MNP5 and V.42bis; or data compression and correction
                  enabled

                          CONNECT MESSAGE FORMAT

  Type:                  Configuration

  Format:                AT [cmds] &An [cmds]

  Description:           Sets the connect message format

        Command                              Function

          &A0            Only CONNECT message

          &A1            CONNECT message and modulation indicator

          &A2            CONNECT message, error detection protocol and
                         data compression indicators

          &A3            CONNECT message, error detection protocol, data
                         compression indicators and modulation indicator

















                       CONNECT MESSAGE SPEED SOURCE

  Type:             Configuration

  Format:           AT [cmds] &En [cmds]

  Description:      Sets the requested source for the speed field in the
                    CONNECT message.

            Note: Used primarily for international data transmission

     Command                              Function

       &E0          DCE speed

       &E1          DTE speed

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR follows circuit definition

                         DATA TERMINAL READY (DTR)

  Type:                  Configuration

  Format:                AT [cmds] &Dn [cmds]

  Description:           Selects modem response to DTR

        Command                              Function

          &D0            Modem does not respond to DTR

          &D1            Modem goes to command mode after DTR goes is off

          &D2            Modem goes to command mode and disconnects
                         (hangs up) after DTR goes off; Auto-Answer is
                         disabled.

          &D3            Modem is initialized after DTR goes off

                           DEFAULT CONFIGURATION

  Type:          Configuration

  Format:        AT [cmds] Yn [cmds]

  Description:   Sets the default configuration

    Command                              Function

       Y0             Select user template 0

       Y1             Select user template 1

       Y2        Select factory setting 0

       Y3        Select factory setting 1





















                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DL             Re-dial last number

          DP             Pulse dialing enabled

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D*             Tone only

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] &F [cmds]

  Description:      Sets values in active profile to values found in the
                    default profile

     Command                              Function

       &F0          Select factory setting 0

       &F1          Select factory setting 1

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Hn [cmds]

  Description:   Sets the flow control

    Command                              Function

      &H0        Disable flow control

      &H1        Enable RTS/CTS emulation























                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I1        Reports modem name, vendor number, version

       I2        Reports software vendor and version number

       I3        Reports chip vendor, ID number

       I4        Reports modem active profile

       I5        Reports stored profile 0 and active profile 0

       I6        Reports stored profile 1 and active profile 1

       I7        Reports stored phone numbers

                                SOFT RESET

  Type:                Immediate

  Format:              AT [cmds] Zn [cmds]

  Description:         Restores modem profiles previously saved in
                       non-volatile RAM using the &W command.

       Command                              Function

          Z0           Select default user template in Y

          Z1           Select user template 0

          Z2           Select user template 1

          Z3           Select factory setting 0

          Z4           Select factory setting 1

                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Low volume setting

       L1        Low volume setting

       L2        Medium volume setting

       L3        Highest volume setting

                                TEST MODES

  Type:          Immediate

  Format:        AT [cmds] &Tn

  Description:   Selects test options

    Command                              Function

      &T0        TBD

      &T1        TBD

      &T2        TBD

      &T3        TBD







                       STANDARD AT# VOICE COMMAND SET

                             INACTIVITY TIMER

  Type:          Immediate

  Format:        AT [cmds] #VIT=n [cmds]

  Description:   Sets the inactivity timer

                               RECEIVE GAIN

  Type:          Immediate

  Format:        AT [cmds] #RG=n [cmds]

  Description:   Sets the receive gainlevel

                             VOICE PARAMETERS

  Type:          Immediate

  Format:        AT [cmds] #VIP=n [cmds]

  Description:   Initializes the voice parameters

                            S(status) -REGISTERS

                             ACTUAL MODULATION

  Type:          Register

  Format         AT [cmds] S37=n [cmds]

  Description:   Returns the actual modulation speed

                              ACTUAL RX SPEED

  Type:          Register

  Format         AT [cmds] S38=n [cmds]

  Description:   Returns the actual RX speed

                               ACTUAL SPEED

  Type:          Register

  Format:        AT [cmds] S35=n [cmds]

  Description:   Sets the actual speed after connect

                                   ADPCM

  Type:           Register

  Format:        AT [cmds] S76=n [cmds]

  Default:       4

  Range:         4, 8, 16

  Description:   Controls the ADPCM bits per sample













                               ANSWER DELAY

  Type:           Register

  Format:        AT [cmds] S92=n [cmds]

  Default:       2

  Range:         0-255

  Description:   Controls the answer delay

                                AUTO ANSWER

  Format         AT [cmds] S27=n [cmds]

  Default:       8

  Range:         0-255

  Unit:          1 second

  Description:   Sets the auto answer clear timeout

                              AUTOMODE SELECT

  Format:        AT [cmds] S31=n [cmds]

  Default:       1

  Range:         0-3

  Description:   Sets automode

                              BEEP TONE TIMER

  Type:           Register

  Format:        AT [cmds] S77=n [cmds]

  Default:       10

  Range:         0-40

  Description:   Sets the beep tone timer

                               BREAK LENGTH

  Format         AT [cmds] S21=n [cmds]

  Default:       9

  Range:         0-9

  Description:   Sets the break length

                                    CD

  Type:           Register

  Format:        AT [cmds] S60=n [cmds]

  Default:       1

  Range:         0-1

  Description:   Sets the CD setting

                                    CID

  Type:           Register

  Format:        AT [cmds] S75=n [cmds]

  Default:       0

  Range:         0,1

  Description:   Controls the CID

                                CIRCUIT 106

  Type:           Register

  Format:        AT [cmds] S66=n [cmds]

  Default:       0

  Range:         0-1

  Description:   Sets the circuit 106 (RTS)

                                CIRCUIT 107

  Type:           Register

  Format:        AT [cmds] S67=n [cmds]

  Default:       0

  Range:         0-1

  Description:   Sets the circuit 107 (DSR)

                                CIRCUIT 109

  Type:           Register

  Format:        AT [cmds] S68=n [cmds]

  Default:       0

  Range:         0-1

  Description:   Sets the circuit 109 (CD)

                              CONNECT MESSAGE

  Type:           Register

  Format:        AT [cmds] S70=n [cmds]

  Default:       0

  Range:         0-1

  Description:   Sets the CONNECT message format

                              CONNECT MESSAGE

  Type:           Register

  Format:        AT [cmds] S71=n [cmds]

  Default:       0

  Range:         0-1

  Description:   Sets the CONNECT message speed source

                               COUNTRY TYPE

  Type:           Register

  Format:        AT [cmds] S162=n [cmds]

  Default:       1

  Range:         0-25

  Description:   Sets the country type













                              CURRENT SETTING

  Type:           Register

  Format:        AT [cmds] S59=n [cmds]

  Default:       3

  Range:         0-5

  Description:   Sets the current setting

                             DATA PUMP STATUS

  Type:          Register

  Format         AT [cmds] S36=n [cmds]

  Description:   Displays the current data pump status

                              DEFAULT SETTING

  Type:           Register

  Format:        AT [cmds] S161=n [cmds]

  Default:       2

  Range:         0-1

  Description:   Sets the default setting

                                    DSR

  Type:           Register

  Format:        AT [cmds] S64=n [cmds]

  Default:       0

  Range:         0-1

  Description:   Sets the DSR

                              DTMF HIGH GAIN

  Type:           Register

  Format:        AT [cmds] S156=n [cmds]

  Default:       0

  Range:         0-255

  Description:   Sets the DTMF high gain level

                               DTMF LOW GAIN

  Type:           Register

  Format:        AT [cmds] S155=n [cmds]

  Default:       0

  Range:         0-255

  Description:   Sets the DTMF low gain level

                                 DTMF TONE

  Type:           Register

  Format:        AT [cmds] S84=n [cmds]

  Default:       0

  Range:         0-3F

  Description:   Controls the DTMF tone reports cap 0

                                 DTMF TONE

  Type:           Register

  Format:        AT [cmds] S85=n [cmds]

  Default:       0

  Range:         0-3F

  Description:   Controls the DTMF tone reports cap 1

                                 DTMF TONE

  Type:           Register

  Format:        AT [cmds] S86=n [cmds]

  Default:       0

  Range:         0-3F

  Description:   Controls the DTMF tone reports cap 2

                                    DTR

  Type:           Register

  Format:        AT [cmds] S63=n [cmds]

  Default:       0

  Range:         0-3

  Description:   Sets the DTR

                                   ECHO

  Type:          Register

  Format         AT [cmds] S13=n [cmds]

  Default:       1

  Range:         0-1

  Description:   Sets the echo

                               EXTENDED CODE

  Type:           Register

  Format:        AT [cmds] S56=n [cmds]

  Default:       4

  Range:         0-4

  Description:   Sets the extended code

                                 FAE VALUE

  Type:           Register

  Format:        AT [cmds] S151=n [cmds]

  Default:       0

  Range:         0,1

  Description:   Sets the FAE value













                               FCLASS VALUE

  Type:           Register

  Format:        AT [cmds] S150=n [cmds]

  Default:       0

  Range:         0,1,8

  Description:   Sets the FCLASS value

                                FLASH TIMER

  Type:                   Register

  Format                  AT [cmds] S24=n [cmds]

  Default:                20

  Range:                  0-255

  Unit:                   10 ms

  Description:            Maximum duration of DTE and DCE inactivity
                          allowed prior to initiating low-power sleep
                          mode.

                                FLASH TIMER

  Type:           Register

  Format:        AT [cmds] S140=n [cmds]

  Range:         0-255

  Description:   Sets the duration of the flash timer

                               FLOW CONTROL

  Type:           Register

  Format:        AT [cmds] S62=n [cmds]

  Default:       1

  Range:         0-3

  Description:   Sets the flow control

                       FLOW CONTROL CHARACTER - XOFF

  Type:          Register

  Format         AT [cmds] S23=n [cmds]

  Default:       19

  Range:         0-127

  Description:   Sets the XOFF character

                               HANDSET GAIN

  Type:           Register

  Format:        AT [cmds] S72=n [cmds]

  Default:       80

  Range:         0-255

  Description:   Sets the handset record gain control











                               HSET OUT GAIN

  Type:           Register

  Format:        AT [cmds] S154=n [cmds]

  Range:         0-255

  Description:   Sets the Hset out gain level

                             INACTIVITY TIMER

  Type:          Register

  Format         AT [cmds] S19=n [cmds]

  Default:       0

  Range:         0-255

  Description:   Sets the system inactivity timer

                               LINE OUT GAIN

  Type:           Register

  Format:        AT [cmds] S152=n [cmds]

  Range:         0-255

  Description:   Sets the line out gain level

                           LINE QUALITY CONTROL

  Type:          Register

  Format         AT [cmds] S39? [cmds]

  Range:         0-2

  Default:       2

  Description:   Displays the line quality control

                             LINE RECORD GAIN

  Type:           Register

  Format:        AT [cmds] S139=n [cmds]

  Range:         0-255

  Description:   Sets the line record gain level

                          LINE SELECTION DURATION

  Type:           Register

  Format:        AT [cmds] S78=n [cmds]

  Default:       0

  Description:   Sets the line selection duration

                                 MAX SPEED

  Type:          Register

  Format:        AT [cmds] S34=n [cmds]

  Description:   Sets the requested MAX speed











                                MICROPHONE

  Type:           Register

  Format:        AT [cmds] S90=n [cmds]

  Default:       1

  Range:         0-3

  Description:   Sets the microphone

                              MICROPHONE GAIN

  Type:           Register

  Format:        AT [cmds] S138=n [cmds]

  Range:         0-255

  Description:   Sets the microphone gain level

                                 MIN SPEED

  Type:          Register

  Format:        AT [cmds] S33=n [cmds]

  Description:   Sets the requested MIN speed

                               ORIGIN/ANSWER

  Type:          Register

  Format         AT [cmds] S22=n [cmds]

  Default:       0

  Range:         0-1

  Description:   Sets the origin/answer

                                 PLAYBACK

  Type:           Register

  Format:        AT [cmds] S74=n [cmds]

  Default:       153

  Range:         0-255

  Description:   Sets the playback volume

                              PROCESSOR TYPE

  Type:           Register

  Format:        AT [cmds] S193=n [cmds]

  Default:       0

  Range:         0-100

  Description:   Sets the processor type

                             PULSE MAKE RATIO

  Type:           Register

  Format:        AT [cmds] S146=n [cmds]

  Default:       39

  Range:         0-100

  Description:   Sets the pulse make ratio





                                PULSE PAUSE

  Type:           Register

  Format:        AT [cmds] S148=n [cmds]

  Default:       80

  Range:         0-255

  Description:   Sets the pulse pause

                                 PULSE PPS

  Type:           Register

  Format:        AT [cmds] S147=n [cmds]

  Default:       10

  Range:         10, 20

  Description:   Sets the pulse PPS

                               PULSE REFRESH

  Type:           Register

  Format:        AT [cmds] S149=n [cmds]

  Default:       0

  Range:         0-100

  Description:   Sets the pulse refresh

                           PULSE SET?BREAK RATIO

  Format         AT [cmds] S28=n [cmds]

  Default:       0

  Range:         0-4

  Description:   Sets the pulse set/break ratio

                                PULSE TONE

  Type:          Register

  Format:        AT [cmds] S16=n [cmds]

  Default:       1

  Range:         0-1

  Description:   Sets the pulse tone

                                   QUIET

  Type:          Register

  Format         AT [cmds] S14=n [cmds]

  Default:       0

  Range:         0-1

  Description:   Sets the quiet function

                           RECEIVED SIGNAL LEVEL

  Format         AT [cmds] S41=n [cmds]

  Description:   Displays the received signal level







                           REQUESTED MODULATION

  Format:        AT [cmds] S32=n [cmds]

  Default:       8

  Range:         Unidentified

  Description:   Sets requested modulation

                               RESULT CODES

  Type:           Register

  Format:        AT [cmds] S43=n [cmds]

  Description:   Controls the result codes

                           RING GOES AWAY TIMER

  Type:           Register

  Format:        AT [cmds] S79=n [cmds]

  Default:       70

  Range:         0-255

  Description:   Sets the ring goes away timer

                           RING NEVER CAME TIMER

  Type:           Register

  Format:        AT [cmds] S80=n [cmds]

  Default:       70

  Range:         0-255

  Description:   Sets the ring never came timer

                                    RTS

  Type:           Register

  Format:        AT [cmds] S61=n [cmds]

  Default:       0

  Range:         0-1

  Description:   Sets the RTS

                           SIGNAL TO NOISE RATIO

  Type:           Register

  Format:        AT [cmds] S42=n [cmds]

  Description:   Controls the signal to noise ratio setting.

                              SILENCE DETECT

  Type:           Register

  Format:        AT [cmds] S81=n [cmds]

  Default:       0

  Range:         0, 1

  Description:   Enables and disables the silence detection









                             SILENCE DETECTION

  Type:           Register

  Format:        AT [cmds] S82=n [cmds]

  Default:       2

  Range:         0-3

  Unit:          0.1 second

  Description:   Controls the silence detection sensitivity

                             SILENCE DETECTION

  Type:           Register

  Format:        AT [cmds] S83=n [cmds]

  Default:       55

  Range:         0-255

  Description:   Controls the silence detection duration

                                  SPEAKER

  Type:           Register

  Format:        AT [cmds] S89=n [cmds]

  Default:       5

  Range:         0-15

  Description:   Sets the speaker

                              SPEAKER CONTROL

  Type:          Register

  Format         AT [cmds] S29=n [cmds]

  Default:       1

  Range:         0-3

  Description:   Sets the speaker control

                               SPEAKER MUTE

  Type:           Register

  Format:        AT [cmds] S88=n [cmds]

  Default:       1

  Range:         0-2

  Description:   Sets the speaker mute

                             SPEAKER OUT GAIN

  Type:           Register

  Format:        AT [cmds] S153=n [cmds]

  Range:         0-255

  Description:   Sets the speaker out gain level













                              SPEAKER VOLUME

  Type:          Register

  Format         AT [cmds] S30=n [cmds]

  Default:       2

  Range:         0-3

  Description:   Sets the speaker volume

                                 TIME MARK

  Type:           Register

  Format:        AT [cmds] S87=n [cmds]

  Default:       0

  Range:         0-255

  Description:   Controls the time mark placement

                            TRANSMIT LEVEL GAIN

  Type:           Register

  Format:        AT [cmds] S45=n [cmds]

  Default:       3

  Range:         0-10

  Description:   Controls the result codes

                                  VERBOSE

  Type:          Register

  Format         AT [cmds] S15=n [cmds]

  Default:       1

  Range:         0-1

  Description:   Sets the verbose function

                               VOICE SAMPLE

  Type:           Register

  Format:        AT [cmds] S91=n [cmds]

  Default:       0

  Range:         1,2

  Description:   Sets the voice sample rate

