
MOTOROLA, INC.

PREMIER 33.6 INTERNAL

Card Type                    Modem (asynchronous)
Chip Set                     Unidentified
Maximum Modem Rate           33.6Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.42, V.32bis, V.32, V.22bis, V.21
Fax Modulation Protocol      ITU-T V.21CH2, V.27ter, V.29, V.17
Error Correction/Compression MNP5, V.42/V.42bis
Fax Class                    Class I & II
Data Bus                     8-bit ISA
Card Size                    Half-length, full-height card

[Image]

                                CONNECTIONS

         Function            Label            Function             Label

  Line in                         CN1       Line out                CN2

                                PLUG & PLAY

     Setting         SW2/1          SW2/2          SW2/3         SW2/4

     Manual            On             On            Off           Off

  Plug and Play       Off            Off            On            On

       COM PORT SELECTION

  Setting    SW1/1      SW1/2

   COM1        On        On

   COM2        On        Off

   COM3       Off        On

   COM4       Off        Off

                    INTERRUPT

  Setting    SW1/3     SW1/4    SW1/5     SW1/6

   IRQ2       On        Off      Off       Off

   IRQ3       Off       On       Off       Off

   IRQ4       Off       Off       On       Off

   IRQ5       Off       Off      Off       On





                             DIAGNOSTIC LED(S)

   LED        Color          Status                 Condition

   AA      Unidentified        On              Auto-answer enabled

   AA      Unidentified        Off             Auto-answer disabled

   AA      Unidentified     Blinking             Phone is ringing

   RD      Unidentified        On         Computer is receiving data from
                                                    the modem

   RD      Unidentified        Off        Computer is not receiving data
                                                  from the modem

   SD      Unidentified        On        Computer is transmitting data to
                                                    the modem

   SD      Unidentified        Off         Computer is not transmitting
                                                data to the modem

   CD      Unidentified        On            Carrier signal detected

   CD      Unidentified        Off         Carrier signal not detected

   OH      Unidentified        On               Modem is off-hook

   OH      Unidentified        Off               Modem is on-hook

   HS      Unidentified        On          Modem is operating at 16800,
                                         19200, 21600, 28800, or 33600bps

   HS      Unidentified        Off          Modem is operating at 4800,
                                           7200, 9600, 12000, 14400bps

   TR      Unidentified        On               DTR signal is high

   TR      Unidentified        Off              DTR signal is low

   MR      Unidentified        On                  Power is on

   MR      Unidentified        Off                 Power is off



                         SUPPORTED COMMAND SET

                           Basic AT Commands

  AT, +++, A/

  A, E, O, S, V, X, Y, Z

  &G, &L, &T, &W, &X, &Y, &Z

                          Extended AT Commands

  \A, \G, \X

                              S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S26

  Note: See MHI Help File for full command documentation.



































                         Proprietary AT Command Set

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DP             Pulse dialing enabled

          DR             Answer mode enabled; originate mode disabled
                         following handshake initiation.

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                               HOOK CONTROL

  Type:          Immediate

  Format:        AT [cmds] Hn [cmds]

  Description:   Selects whether the modem is on-hook or off-hook

    Command                              Function

       H0        Modem commanded to go on-hook (hang-up)

       H1        Modem commanded to go off-hook (pick-up)

       H2        Set H command to allow cleardown

       H3        Set H command to disallow cleardown

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports EPROM CRC value

       I3        Reports product version

       I4        Reports capability code

       I5        Reports disconnect reason





                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Low volume setting

       L1        Low volume setting

       L2        Medium volume setting

       L3        Highest volume setting

                               SPEAKER MODE

  Type:                Configuration

  Format:              AT [cmds] Mn [cmds]

  Description:         Selects various speaker options

       Command                             Function

         M0            Speaker disabled

         M1            Speaker enabled until carrier signal detected

         M3            Speaker enabled following dialing, then disabled
                       after carrier signal detected.

                               RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] Qn [cmds]

  Description:   Enables modem to send result codes to the DTE

    Command                              Function

       Q0        Result code sending enabled

       Q1        Result code sending disabled

       Q2        Result code sending in originate mode only

                         DATA CARRIER DETECT (DCD)

  Type:          Configuration

  Format:        AT [cmds] &Cn [cmds]

  Description:   Selects whether the DCD option is enabled or disabled

    Command                              Function

      &C0        DCD enabled

      &C1        DCD enabled after carrier signal detected

      &C2        DCD off 5 seconds after disconnect

      &C3        DCD follows remote RTS





















                         DATA TERMINAL READY (DTR)

  Type:                 Configuration

  Format:               AT [cmds] &Dn [cmds]

  Description:          Selects modem response to DTR

            Note: The action each variant of &D causes depends on the
            setting of &Q

        Command                             Function

          &D0           Modem does not respond to DTR

          &D1           Modem goes to command mode after DTR goes is off

          &D2           Modem goes to command mode and disconnects (hangs
                        up) after DTR goes off; Auto-Answer is disabled.

          &D3           Modem is initialized after DTR goes off

          &D9           DTR dials/disconnects

                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] &F [cmds]

  Description:      Sets values in active profile to values found in the
                    default profile

     Command                              Function

       &F0          Restore factory default 0

       &F1          Restore factory default 1

                            COMMUNICATIONS MODE

  Type:             Configuration

  Format:           AT [cmds] &Mn [cmds]

  Description:      Selects communications mode

     Command                                Mode

       &M0          Asynchronous dial/asynchronous data

       &M1          Asynchronous dial/synchronous data

       &M2          Dial stored number when DTR off/on transition is
                    detected/sync data

       &M3          Manual dial/sync data

       &M4          V.25bis dialer/BISYNC protocol/sync data (EBCDIC)

       &M5          V.25bis dialer/SDLC protocol/sync data (NRZ)

       &M6          V.25bis async dial/sync data

       &M7          V.25bis async dial/async data

       &M8          V.25bis dialer w/BISYNC protocol/sync data (EBCDIC)

       &M9          V.25bis dialer w/SDLC protocol/sync data (EBCDIC)
                    (NRZ)

       &M10         V.25bis dialer w/SDLC protocol/sync data (ASCII)
                    (NRZI)

       &M11         V.25bis dialer w/SDLC protocol/sync data (EBCID)
                    (NRZI)

                            PULSE DIALING RATIO

  Type:          Configuration

  Format:        AT [cmds] &Pn [cmds]

  Description:   Selects pulse dial make/break ratio

    Command                              Function

      &P0        39/61ms at 10pps (North America)

      &P1        33/67ms at 10pps (Europe)

                                  RTS/CTS

  Type:           Configuration

  Format:         AT [cmds] &Rn [cmds]

  Description:    Selects RTS/CTS options

    Command                              Function

      &R0         CTS follows RTS in data mode; RTS is ignored in command
                  mode.

      &R1         CTS forced high, RTS is ignored.

      &R2         CTS follows DCD

      &R9         CTS equals RTS

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high when ready to accept data

      &S2        DSR off for 5 seconds after disconnect

      &S3        DSR follows off hook

                          CONFIGURATION PROFILES

  Type:          Immediate

  Format:        AT [cmds] &V [cmds]

  Description:   Displays active and stored configuration profiles

    Command                              Function

      &V0        View configuration profiles

      &V1        Displays received signal status

      &V2        Displays active profile

                            Extended AT Commands

                                BREAK SEND

  Type:          Configuration

  Format:        AT [cmds] \Bn [cmds]

  Default:       35

  Range:         1-255

  Unit:          20ms

  Description:   Sends break to modem

    Command                              Function

      \B0        Transmit break signal

      \B1        Set break length in 20ms increments

                  AUTO-RELIABLE TIME BUFFER CONFIGURATION

  Type:              Configuration

  Format:            AT [cmds] \Cn [cmds]

  Description:       Controls the handling of incoming data during
                     auto-reliable time period

      Command                             Function

        \C0          Data is discarded

        \C1          Data is buffered

                             LOCK SERIAL PORT

  Type:          Configuration

  Format:        AT [cmds] \Jn [cmds]

  Description:   Sets operation of serial port speed

    Command                              Function

      \J0        Serial speed locked

      \J1        Serial speed follows connect speed

      \J2        Enable 230.4Kbps serial speed

      \J3        Disable 230.4Kbps serial speed

                                BREAK TYPE

  Type:          Configuration

  Format:        AT [cmds] \Kn [cmds]

  Description:   Configures action of break signal

    Command                              Function

      \K1        Break signals empty data buffers

      \K3        Expedite break signals

      \K5        Sequence break signals with data

                             V.42 FAST DETECT

  Type:          Configuration

  Format:        AT [cmds] \Mn [cmds]

  Description:   Controls the V.42 fast detect data sequence

    Command                              Function

      \M0        V.42 fast detect data sequence disabled

      \M1        V.42 fast detect data sequence enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        MNP mode

      \N3        MNP with normal fallback

      \N4        LAPM only

      \N5        LAPM with normal fallback

      \N6        LAPM with MNP fallback

      \N7        LAPM with MNP and normal fallback

                             FLOW CONTROL TYPE

  Type:          Configuration

  Format:        AT [cmds] \Qn [cmds]

  Description:   Sets type of flow control used by modem

    Command                              Function

      \Q0        Flow control disabled

      \Q1        Bidirectional XON/XOFF flow control enabled

      \Q2        CTS flow control by DCE enabled

      \Q3        Bidirectional RTS/CTS flow control enabled

                               RING INDICATE

  Type:          Configuration

  Format:        AT [cmds] \Rn [cmds]

  Description:   Controls the ring indicator

    Command                              Function

      \R0        LED AA blinks for ring and remains on during the call

      \R1        LED AA blinks for ring and turns off when call is
                 answered

                             INACTIVITY TIMER

  Type:                  Configuration

  Format:                AT [cmds] \Tn [cmds]

  Range:                 1-255

  Unit:                  1 second

  Description:           Sets the length of time that the modem does not
                         receive information before it disconnects.

                           EXTENDED RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] \Vn [cmds]

  Description:   Selects extended result codes

    Command                              Function

      \V0        Connect message shows computer speed

      \V1        Connect message shows computer speed/protocol

      \V2        Connect message shows modem speed

      \V3        Connect message shows speed/protocol

      \V4        Connect message shows modem speed/modulation/protocol























                              SPEED SELECTION

  Type:          Configuration

  Format:        AT [cmds] %Bn [cmds]

  Description:   Selects the maximum connect speed

    Command                              Function

      %B0        Use computer speed

      %B1        300bps

      %B2        1200bps

      %B3        2400bps

      %B4        4800bps

      %B5        9600bps uncoded

      %B6        9600bps

      %B7        7200bps

      %B8        12000bps

      %B9        14400bps

      %B10       600bps

      %B11       16800bps

      %B12       19200bps

      %B13       21600bps

      %B14       24000bps

      %B15       26400bps

      %B16       28800bps

      %B17       31200bps

      %B18       33600bps

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] %Cn [cmds]

  Description:   Selects data compression

    Command                              Function

      %C0        Compression disabled

      %C1        Compression enabled on transmit and receive data

                          DISCONNECT BUFFER DELAY

  Type:          Configuration

  Format:        AT [cmds] %Dn [cmds]

  Description:   Controls the disconnect buffer delay

    Command                              Function

      %D0        Disable disconnect buffer delay

      %D1        Set disconnect buffer delay in seconds n (n= 1 - 255)















                          MINIMUM SPEED SELECTION

  Type:          Immediate

  Format:        AT [cmds] %L [cmds]

  Description:   Sets the minimum speed level

    Command                              Function

      %L0        300bps

      %L1        300bps

      %L2        1200bps

      %L3        2400bps

      %L4        4800bps

      %L5        9600bps uncoded

      %L6        9600bps

      %L7        7200bps

      %L8        12000bps

      %L9        14400bps

      %L10       600bps

      %L11       16800bps

      %L12       19200bps

      %L13       21600bps

      %L14       24000bps

      %L15       26400bps

      %L16       28800bps

      %L17       31200bps

      %L18       33600bps

                           REMOTE CONFIGURATION

  Type:          Immediate

  Format:        AT [cmds] %P [cmds]

  Description:   Displays the remote configuration code

                          AUTOMATIC RATE ADAPTION

  Type:          Immediate

  Format:        AT [cmds] %Rn [cmds]

  Description:   Send PTT test signals for a line tests

    Command                              Function

      %R0        Disable automatic rate adaption

      %R1        Enable automatic rate adaption low BER

      %R2        Enable automatic rate adaption medium BER

      %R3        Enable automatic rate adaption using high BER

                               TEST PATTERN

  Type:          Immediate

  Format:        AT [cmds] %Tn [cmds]

  Description:   Transmit test pattern







                             PRODUCT REVISION

  Type:          Immediate

  Format:        AT [cmds] %Vn [cmds]

  Description:   Display product revision level

                           V.34 ASYMMETRIC RATE

  Type:          Immediate

  Format:        AT [cmds] *ASn [cmds]

  Description:   Sets the asymmetric bit rate

    Command                              Function

      *AS0       Disable V.34 asymmetric bit rate

      *AS1       Enable V.34 asymmetric bit rate

                           BILTERAL DIGITAL LOOP

  Type:          Immediate

  Format:        AT [cmds] *DGn [cmds]

  Description:   Controls the bilateral digital loop

    Command                              Function

      *DG0       Disables the bilateral digital loop

      *DG1       Enables the digital bilateral loop

                              TEST MODE - PTT

  Type:          Immediate

  Format:        AT [cmds] *DNn [cmds]

  Description:   Send PTT test signals for a line tests

    Command                              Function

      *DN0       Allow redial with A/

      *DN1       Disallow redial with A/

                        DISTINCTIVE RING DETECTION

  Type:          Immediate

  Format:        AT [cmds] *DRn [cmds]

  Description:   Controls the distinctive ring detection

    Command                              Function

      *DR0       Disable distinctive ring detection

      *DR1       Enable distinctive ring detection

                                FAST TRAIN

  Type:          Immediate

  Format:        AT [cmds] *FTn [cmds]

  Description:   Controls the fast train

    Command                              Function

      *FT0       Disables the fast train

      *FT1       Enables the fast train





                                 CALLER ID

  Type:          Immediate

  Format:        AT [cmds] *IDn [cmds]

  Description:   Controls the caller ID function

    Command                              Function

      *ID0       Disable caller ID

      *ID1       Enable caller ID

                                MODULATION

  Type:          Immediate

  Format:        AT [cmds] *MMn [cmds]

  Description:   Sets the modulation

    Command                              Function

      *MM0       Automode

      *MM1       V.21

      *MM2       Bell 103J

      *MM3       V.23

      *MM4       Bell 212A

      *MM5       V.22bis

     *MM11       V.32bis

     *MM12       V.34

                              STORED NUMBERS

  Type:          Immediate

  Format:        AT [cmds] *ND [cmds]

  Description:   Displays the nine stored numbers

                               AT COMMANDSET

  Type:          Immediate

  Format:        AT [cmds] *NTn [cmds]

  Description:   Controls the AT command set

    Command                              Function

      *NT0       AT command set disabled

      *NT1       AT command set enabled

                              MODE SELECTION

  Type:          Immediate

  Format:        AT [cmds] *ORn [cmds]

  Description:   Controls the originate or answer mode

    Command                              Function

      *OR0       Originate mode active

      *OR1       Answer mode active











                        RATE NEGOTIATION SELECTION

  Type:          Immediate

  Format:        AT [cmds] *RRn [cmds]

  Description:   Sets the rate negotiation

    Command                              Function

      *RR0       Rate negotiation to 2400

      *RR1       Rate negotiation to 4800

      *RR2       Rate negotiation to 7200

      *RR3       Rate negotiation to 9600

      *RR4       Rate negotiation to 12000

      *RR5       Rate negotiation to 14400

      *RR6       Rate negotiation to 16800

      *RR7       Rate negotiation to 19200

      *RR8       Rate negotiation to 21600

      *RR9       Rate negotiation to 24000

     *RR10       Rate negotiation to 26400

     *RR11       Rate negotiation to 28800

     *RR12       Rate negotiation to 31200

     *RR13       Rate negotiation to 33600

                               RATE ADAPTION

  Type:          Immediate

  Format:        AT [cmds] *RUn [cmds]

  Description:   Controls the rate adaption

    Command                              Function

      *RU0       Disable auto rate adaption above initial rate

      *RU1       Enable auto rate adaption above initial rate

                              TRANSMIT LEVEL

  Type:          Immediate

  Format:        AT [cmds] *TDn [cmds]

  Description:   Set dial transmit level from -9 to -30dBm

                         RATE SELECTION THRESHOLD

  Type:          Immediate

  Format:        AT [cmds] *THn [cmds]

  Description:   Sets the rate selection threshold

    Command                              Function

      *TH0       Low V.34 rate selection threshold

      *TH1       Medium V.34 rate selection threshold

      *TH2       High V.34 rate selection threshold

                        LEASED LINE TRANSMIT LEVEL

  Type:          Immediate

  Format:        AT [cmds] *TLn [cmds]

  Description:   Sets the leased line transmit level (0 - 30)



                                ONLINE HELP

  Type:          Immediate

  Format:        AT [cmds] $Hn [cmds]

  Description:   Online help

    Command                              Function

   $H=string     Online help

                           PRODUCT SERIAL NUMBER

  Type:          Immediate

  Format:        AT [cmds] $Vn [cmds]

  Description:   Displays the product serial number

                             Security Commands

                           USER CALLBACK NUMBER

  Type:              Immediate

  Format:            AT [cmds] $Cn=m [cmds]

  Description:       Sets the user callback number (n= user number and m=
                     the callback number

                             SECURITY DISABLED

  Type:          Immediate

  Format:        AT [cmds] $D [cmds]

  Description:   Disables security

                              SECURITY STATUS

  Type:          Immediate

  Format:        AT [cmds] $D? [cmds]

  Description:   Reports the security status

                              SECURITY ENABLE

  Type:          Immediate

  Format:        AT [cmds] $EH=pw [cmds]

  Description:   Enables security (pw=superuser password)

                           REINITIALIZE SECURITY

  Type:          Immediate

  Format:        AT [cmds] $F=pw$pw [cmds]

  Description:   Reinitializes security (pw=superuser password)

                             USER INFORMATION

  Type:          Immediate

  Format:        AT [cmds] $I [cmds]

  Description:   Reports all secure user information







                              SECURITY LEVEL

  Type:          Immediate

  Format:        AT [cmds] $Ln=m [cmds]

  Description:   Set security level for the user specified by n

                       ILLEGAL ATTEMPTS INFORMATION

  Type:          Immediate

  Format:        AT [cmds] $M [cmds]

  Description:   Reports illegal attempts information

                        RESET ALL ILLEGAL ATTEMPTS

  Type:               Immediate

  Format:             AT [cmds] $M* [cmds]

  Description:        Reset all illegal attempts registers/restore
                      suspended users to normal status

                          RESET ILLEGAL ATTEMPTS

  Type:              Immediate

  Format:            AT [cmds] $Mn [cmds]

  Description:       Reset illegal attempts registers/restore suspended
                     users to normal status

                                LOCAL LOGON

  Type:          Immediate

  Format:        AT [cmds] $n=pw [cmds]

  Description:   Local logon (n = user number, pw = password)

                               SET PASSWORD

  Type:                 Immediate

  Format:               AT [cmds] $Pn=pw$pw [cmds]

  Description:          Set user password (n = user number, pw = new
                        password, n = 0 for superuser password)

                                REMOVE USER

  Type:          Immediate

  Format:        AT [cmds] $Rn [cmds]

  Description:   Removes a user

                             SUPERUSER STATUS

  Type:          Immediate

  Format:        AT [cmds] $S=pw [cmds]

  Description:   Request superuser status (pw = password)

                            CURRENT USER STATUS

  Type:          Immediate

  Format:        AT [cmds] $S? [cmds]

  Description:   Reports current user status



                                LOCAL LOGON

  Type:          Immediate

  Format:        AT [cmds] $n=m [cmds]

  Description:   Local logon (n = user number and m = password)

                       Remote Configuration Commands

                       REMOTE CONFIGURATION SECURITY

  Type:          Immediate

  Format:        AT [cmds] %P=n [cmds]

  Description:   Set the remote configuration security code to value n

                           DISPLAY SECURITY CODE

  Type:          Immediate

  Format:        AT [cmds] %P? [cmds]

  Description:   Displays the remote configuration security code

                            CLEAR SECURITY CODE

  Type:          Immediate

  Format:        AT [cmds] %P = (blank) [cmds]

  Description:   Clears the security code

                              COMPUTER SPEED

  Type:          Immediate

  Format:        AT [cmds] *RBn [cmds]

  Description:   Sets the remote configuration computer speed

    Command                              Function

      *RB0       300bps

      *RB1       600bps

      *RB2       1200bps

      *RB3       2400bps

      *RB4       4800bps

      *RB5       7200bps

      *RB6       9600bps

      *RB7       12000bps

      *RB8       14400bps

      *RB9       16800bps

     *RB10       19200bps

     *RB11       21600bps

     *RB12       24000bps

     *RB13       26400bps

     *RB14       28800bps

     *RB15       28400bps

     *RB16       57600bps

     *RB17       115200bps



                              FORMAT SETTINGS

  Type:          Immediate

  Format:        AT [cmds] *RFn [cmds]

  Description:   Sets the remote configuration format settings

    Command                              Function

      *RF0       7 data bits, mark parity, 1 stop bit

      *RF1       7 data bits, no parity, 2 stop bit

      *RF2       7 data bits, odd parity, 1 stop bit

      *RF3       7 data bits, even parity, 1 stop bit

      *RF4       8 data bits, mark parity, 1 stop bit

      *RF5       8 data bits, no parity, 1 stop bit

      *RF6       8 data bits, odd parity, 1 stop bit

      *RF7       8 data bits, even parity, 1 stop bit

                         SAVE REMOTE CONFIGURATION

  Type:             Immediate

  Format:           AT [cmds] *RQn [cmds]

  Description:      Exit remote configuration and saves or discards the
                    new configuration

     Command                              Function

       *RQ0         Save new configuration

       *RQ1         Discard new configuration

                            S(status) -REGISTERS

                          REMOTE ESCAPE CHARACTER

  Format         AT [cmds] S41=n [cmds]

  Default:       61

  Range:         1-255

  Unit:          20ms

  Description:   Sets the remote escape character

                             REMOTE GUARD TIME

  Format         AT [cmds] S42=n [cmds]

  Default:       50

  Range:         0-255

  Unit:          ASCII

  Description:   Sets the remote guard time

                     COMPUTER CONTROL CHARACTER - XON

  Format         AT [cmds] S44=n [cmds]

  Default:       17

  Range:         0-127

  Unit:          ASCII

  Description:   Sets the character used to represent XON for the
                 computer







                     COMPUTER CONTROL CHARACTER - XOFF

  Format         AT [cmds] S45=n [cmds]

  Default:       19

  Range:         0-127

  Unit:          ASCII

  Description:   Sets the character used to represent XOFF for the
                 computer

                       MODEM CONTROL CHARACTER - XON

  Format         AT [cmds] S49=n [cmds]

  Default:       17

  Range:         0-127

  Description:   Sets the character used to represent XON for the modem

                      MODEM CONTROL CHARACTER - XOFF

  Format         AT [cmds] S50=n [cmds]

  Default:       19

  Range:         0-127

  Unit:          ASCII

  Description:   Sets the character used to represent XOFF for the modem

                         PASSWORD TIMEOUT SECURITY

  Format         AT [cmds] S73=n [cmds]

  Default:       0

  Range:         0-255

  Description:   Sets the password timeout security

                              CALLBACK DELAY

  Format         AT [cmds] S74=n [cmds]

  Default:       15

  Range:         0-255

  Description:   Sets the callback delay

                              CALLBACK RETRY

  Format         AT [cmds] S75=n [cmds]

  Default:       0

  Range:         0-255

  Description:   Sets the callback retry

                           CALLBACK RETRY DELAY

  Format         AT [cmds] 76=n [cmds]

  Default:       15

  Range:         1-255

  Description:   Sets the callback retry delay

                             LOCKOUT THRESHOLD

  Format         AT [cmds] S77=n [cmds]

  Default:       0

  Range:         0-255

  Description:   Sets the lockout threshold



