
MOTOROLA, INC

MOBILESURFR 56K

Card Type                    Modem (asynchronous)
Chip Set                     Unidentified
Maximum Modem Rate           56Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Bell 103/212

                             ITU-T V.34, V.32bis, V.32, V.22bis, V.22,
                             V.21, K56flex
Fax Modulation Protocol      ITU-T V.17, V.29, V.27ter, V.21 channel 2
Error Correction/Compression V.42, V.42bis, MNP5, MNP10, MNP10EC
Fax Class                    Unidentified
Data Bus                     PCMCIA Type II

                                                                      54912

                           SUPPORTED COMMAND SET

                             Basic AT Commands

  AT, +++, A/

  A, B, E, H, M, O, Q, V, W, X, Y, Z

  &C, &P, &R, &T, &V, &W, &Y, &Z

                           Extended AT Commands

  \A, \B, \K, \N, \V

  %C, %E, %L, %Q

                                S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S24, S25,

  S26, S27, S28, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48,
  S82, S86, S91, S92, S95

                             Special Commands

  -K, #CID, +MS

  Note: See MHI Help File for full command documentation.

                         Proprietary AT Command Set

                            AUTO-MODE DETECTION

  Type:                  Configuration

  Format:                AT [cmds] Nn [cmds]

  Description:           Selects various options for the automatic
                         detection and negotiation of protocols during
                         the handshake process if the modem is
                         communicating with a remote modem of dissimilar
                         speed.

        Command                              Function

          N0             Automode detection disable

          N1             Automode detection enable

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected





                         DATA TERMINAL READY (DTR)

  Type:                  Configuration

  Format:                AT [cmds] &Dn [cmds]

  Description:           Selects modem response to DTR

            Note: The action each variant of &D causes depends on the
            setting of &Q

        Command                              Function

          &D0            Modem does not respond to DTR

          &D1            Modem goes to command mode after DTR goes is off

          &D2            Modem goes to command mode and disconnects
                         (hangs up) after DTR goes off; Auto-Answer is
                         disabled.

          &D3            Modem is initialized after DTR goes off

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DL             Re-dial last number

          DP             Pulse dialing enabled

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] &F [cmds]

  Description:      Sets values in active profile to values found in the
                    default profile

     Command                              Function

       &F0          Load factory setting 0

       &F1          Load factory setting 1















                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K3        Bi-directional RTS/CTS flow control enabled

      &K4        Bi-directional XON/XOFF flow control enabled

      &K5        Transparent XON/XOFF flow control enabled

      &K6        RTS/CTS and XON/XOFF flow control enabled

                                GUARD TONE

  Type:           Configuration

  Format:         AT [cmds] &Gn [cmds]

  Description:    Commands the modem to transmit a guard tone in
                  V.22/V.22bis

            Note: Used primarily for international data transmission

    Command                              Function

      &G0         Guard tone disabled

      &G1         Guard tone disabled

      &G2         1800Hz guard tone enabled

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports EPROM CRC value

       I2        Displays OK

       I3        Reports firmware revision number

       I4        Reports Motorola 56K

       I5        Reports country code parameter

       I6        Reports data pump model and code revision

                               SPEAKER MODE

  Type:          Configuration

  Format:        AT [cmds] Mn [cmds]

  Description:   Selects various speaker options

    Command                              Function

       M0        Speaker disabled















                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Speaker disabled

                             TRANSMIT CARRIER

  Type:           Configuration

  Format:         AT [cmds] Cn [cmds]

  Description:    Controls the transmit carrier switching

            Note: Command performs no function; included for
            compatibility only.

                            Special AT Commands

                             DISTINCTIVE RING

  Type:          Configuration

  Format:        AT [cmds] -SDR=n [cmds]

  Description:   Controls distinctive ring

    Command                              Function

     -SDR=0      Distinctive ring disable

     -SDR=1      Distinctive ring enable ring type A

     -SDR=2      Distinctive ring enable ring type B

     -SDR=3      Distinctive ring enable ring type A and B

     -SDR=4      Distinctive ring enable ring type C

     -SDR=5      Distinctive ring enable ring type A and C

     -SDR=6      Distinctive ring enable ring type B and C

     -SDR=7      Distinctive ring enable ring type A, B, and C

                                 MNP10-EC

  Type:          Configuration

  Format:        AT [cmds] -SECn [cmds]

  Description:   Controls MNP10-EC

    Command                              Function

     -SEC0       Disable

     -SEC1       Enable and set TX level (0-30dB/m)

                            S(status) -REGISTERS

                             AUTO-SYNC OPTIONS

  Type:          Register

  Format         AT [cmds] S19=n [cmds]

  Default:       0

  Range:         Unidentified

  Unit:          1 second

  Description:   Sets the auto-sync options

                               HDLC ADDRESS

  Type:          Register

  Format         AT [cmds] S20=n [cmds]

  Default:       0

  Range:         Unidentified

  Unit:          1 second

  Description:   Sets the HDLC address or BSC sync character















