
MOTOROLA, INC.

LIFESTYLE 33.6K

Card Type                    Modem (asynchronous)
Chip Set                     Unidentified
Maximum Modem Rate           33.6Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Bell 103/212A

                             ITU-T V.34, V.32bis, V.32, V.23, V.21
Fax Modulation Protocol      ITU-T V.17, V.29, V.27ter, V.21 CH 2
Error Correction/Compression V.42, V.42bis, MNP5
Fax Class                    Class I & II
Data Bus                     External

[Image]

                                CONNECTIONS

        Function           Label             Function              Label

  Line in                       CN1      Computer connector         CN3

  Line out                      CN2

                             DIAGNOSTIC LED(S)

   LED        Color         Status                  Condition

   RD      Unidentified       On           Computer is receiving data

   RD      Unidentified       Off        Computer is not receiving data

   TD      Unidentified       On          Computer is transmitting data

   TD      Unidentified       Off       Computer is not transmitting data

   CD      Unidentified       On             Carrier signal detected

   CD      Unidentified       Off          Carrier signal not detected

   OH      Unidentified       On                Modem is off-hook

   OH      Unidentified       Off               Modem is on-hook

   TR      Unidentified       On               DTR signal is high

   TR      Unidentified       Off               DTR signal is low

   PWR     Unidentified       On                   Power is on

   PWR     Unidentified       Off                 Power is off





                   SUPPORTED COMMAND SET

                     Basic AT Commands

  AT, +++, A/

  A, E, F, H, Q, V, Z

  &C, &F, &G, &V, &Z

                   Extended AT Commands

  \T, \V

                        S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12

  Note: See MHI Help File for full command documentation.

                         Proprietary AT Command Set

                            AUTO-MODE DETECTION

  Type:                  Configuration

  Format:                AT [cmds] Nn [cmds]

  Description:           Selects various options for the automatic
                         detection and negotiation of protocols during
                         the handshake process if the modem is
                         communicating with a remote modem of dissimilar
                         speed.

        Command                              Function

          N0             Negotiate handshake only at speed specified in
                         S37 and standard set by B

          N1             Negotiate handshake only at speed specified in
                         S37 and standard set by B with fallback to lower
                         speed allowed.

                              AUXILIARY RELAY

  Type:          Configuration

  Format:        AT [cmds] &Jn [cmds]

  Description:   Controls the auxilliary relay

    Command                             Jack Type

      &J0        Never closed

                          COMMUNICATION PROTOCOLS

  Type:                  Configuration

  Format:                AT [cmds] Bn [cmds]

  Description:           Selects the communication protocol for data
                         calls

            Note: The B command allows the simultaneous selection of more
            than one suffix, enabling multiple protocols.

        Command                              Protocol

          B0             ITU-T V.22 at 300 or 1200bps

          B1             Bell 212A at 300 or 1200bps

          B2             Disable V.23 reverse channel

          B3             Disable V.23 reverse channel

          B15            V.21 at 300bps

          B16            Bell 103J at 300bps





                            COMMUNICATIONS MODE

  Type:          Configuration

  Format:        AT [cmds] &Qn [cmds]

  Description:   Selects communications mode options

    Command                                Mode

      &Q0        Asynchronous mode, buffered

      &Q1        Reserved

      &Q2        Reserved

      &Q3        Reserved

      &Q4        Reserved

      &Q5        Error correction mode, buffered

      &Q6        Buffered asynchronous mode

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected

                         DATA TERMINAL READY (DTR)

  Type:                  Configuration

  Format:                AT [cmds] &Dn [cmds]

  Description:           Selects modem response to DTR

            Note: The action each variant of &D causes depends on the
            setting of &Q

        Command                              Function

          &D0            Modem does not respond to DTR

          &D1            Modem goes to command mode after DTR goes is off

          &D2            Modem goes to command mode and disconnects
                         (hangs up) after DTR goes off; Auto-Answer is
                         disabled.

          &D3            Modem is initialized after DTR goes off

































                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DL             Re-dial last number

          DP             Pulse dialing enabled

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D^             Disable data calling tone transmission

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                             ECHOPLEX VALIDITY

  Type:           Configuration

  Format:         AT [cmds] Fn [cmds]

  Description:    Selects whether commands sent while in data mode are
                  echoed

            Note: This command is only supported on older modems

    Command                              Function

       F1         Echoplex disabled

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K1        Reserved

      &K2        Reserved

      &K3        RTS/CTS flow control enabled

      &K4        XON/XOFF flow control enabled

                           LONG SPACE DISCONNECT

  Type:             Configuration

  Format:           AT [cmds] Yn [cmds]

  Description:      Commands the modem to disconnect after a 1.6 second
                    break is detected

     Command                              Function

        Y0          Long space disconnect function disabled

                                  ON-LINE

  Type:               Immediate

  Format:             AT [cmds] On [cmds]

  Description:        Controls on-line command (data transmission) state
                      options.

            Note: The O command must be placed at the end of the command
            string.

      Command                              Function

         O0           On-line command mode with no retraining enabled

         O1           On-line command mode with retraining enabled

         O3           Renegotiate rate before returning to data mode
                      after escape for command entry

                            REPORT INFORMATION

  Type:           Immediate

  Format:         AT [cmds] In [cmds]

  Description:    Displays information requested

    Command                              Function

       I0         Reports default speed and controller firmware revision
                  number

       I1         Reports ROM checksum

       I2         Perform checksum and reports OK or ERROR

       I3         Reports default speed and controller firmware revision
                  number

       I4         Reports firmware revision number

                        RESTORE PROFILE ON POWER-UP

  Type:               Configuration

  Format:             AT [cmds] &Yn [cmds]

  Description:        Restores a selected profile into the active profile
                      on power-up (hard reset)

      Command                              Function

        &Y0           Restore profile 0 on power-up

                     SELECT CALL PROGRESS RESULT CODES

  Type:                  Configuration

  Format:                AT [cmds] Xn [cmds]

  Description:           Enables selection of tone detection and
                         associated result code format options

        Command                              Function

           X0            Busy and dial tone detection disabled; result
                         codes 0 - 4 enabled.

           X1            Busy and dial tone detection disabled; result
                         codes 0 - 5 & 10 enabled.

           X2            Busy tone detection disabled, dial tone
                         detection enabled; result codes 0 - 6 & 10
                         enabled.

           X3            Busy tone detection enabled, dial tone detection
                         disabled; result codes 0 - 5, 7 & 10 enabled.

           X4            Busy and dial tone detection enabled; result
                         codes 0 - 7 & 10 enabled.

           X5            Busy and dial tone detection enabled; result
                         codes 0 - 7 & 10 enabled.

           X6            Busy and dial tone detection enabled; result
                         codes 0 - 7 & 10 enabled.

           X7            Connect for all speeds, wait for dial tone,
                         check for busy signal after dialing









                           STORE ACTIVE PROFILE

  Type:            Configuration

  Format:          AT [cmds] &Wn [cmds]

  Description:     Writes the values for the active profile into the
                   non-volatile RAM

     Command                              Function

       &W0         Write the active profile to stored profile 0

                                TEST MODES

  Type:          Immediate

  Format:        AT [cmds] &Tn

  Description:   Selects test options

    Command                              Function

      &T0        End current test

      &T1        Begin local analog loopback test

      &T3        Begin local digital loopback

      &T6        Grant remote digital loopback request

                             TRANSMIT CARRIER

  Type:            Configuration

  Format:          AT [cmds] Cn [cmds]

  Description:     Controls the transmit carrier switching

            Note: Disabling the transmit carrier puts the modem in
            receive-only mode

     Command                              Function

       C1          Transmit carrier enabled

                            V.32 - AUTO-RETRAIN

  Type:            Configuration

  Format:          AT [cmds] &Bn [cmds]

  Description:     Controls auto-retrain function if poor line quality is
                   detected

     Command                             Function

       &B1         Auto-retrain enabled if line quality is poor

                            EXTENDED AT COMMANDS

                                BREAK TYPE

  Type:           Configuration

  Format:         AT [cmds] \Kn [cmds]

  Description:    Configures action of break signal

    Command                              Function

      \K5        Non-destructive/non-expedited break













                                BUFFER MODE

  Type:          Configuration

  Format:        AT [cmds] \Jn [cmds]

  Description:   Sets the buffer mode

    Command                              Function

      \J0        Buffer mode enabled, error control selected by /Nn

                               CALLING TONE

  Type:          Configuration

  Format:        AT [cmds] -Cn [cmds]

  Description:   Controls the calling tone

    Command                              Function

      -C0        Calling tone disabled

      -C1        Calling tone enabled

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] %Cn [cmds]

  Description:   Selects data compression

    Command                              Function

      %C0        Data compression disabled

      %C1        V.42bis MNP5 enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        Reliable mode enabled

      \N3        Auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

      \N5        Auto-reliable mode enabled

      \N7        Auto-reliable mode enabled

                               FLOW CONTROL

  Type:             Configuration

  Format:           AT [cmds] \Gn [cmds]

  Description:      Selects modem port flow control

     Command                              Function

       \G0          Command is included for compatibility only; it
                    performs no function











                             FLOW CONTROL TYPE

  Type:          Configuration

  Format:        AT [cmds] \Qn [cmds]

  Description:   Sets type of flow control used by modem

    Command                              Function

      \Q0        Flow control disabled

      \Q1        XON/XOFF flow control enabled

      \Q3        RTS/CTS flow control enabled

                           XON/XOFF PASS-THROUGH

  Type:          Configuration

  Format:        AT [cmds] \Xn [cmds]

  Description:   Selects whether XON/XOFF signals are sent to remote
                 modem

    Command                              Function

      \X0        XON/XOFF signals trapped by local modem

                            S(status) -REGISTERS

                      AUTO-RATE AND RETRAIN SELECTION

  Format           AT [cmds] S42=n [cmds]

  Default:         1

  Range:           0-1

  Unit:            Bit-mapped

  Description:     Controls the V.32bis and V.22bis auto rate/V.32
                   retrain operation

                          BIT-MAPPED REGISTER S28

  Format         AT [cmds] S28=n [cmds]

  Default:       1

  Range:         0-255

  Unit:          Bit-mapped

  Description:   Controls V.34 modulation.

                               CALLING TONE

  Type:          Register

  Format         AT [cmds] S35=n [cmds]

  Default:       1

  Range:         0-1

  Description:   Sets the data calling tone



















                              DCE LINE SPEED

  Type:                Register

  Format               AT [cmds] S37=n [cmds]

  Description:         Sets the maximum allowable data exchange rate
                       attempted during handshake process.

       Command                              Function

        S37=0          Maximum modem speed

        S37=2          1200/75bps

        S37=3          300bps

        S37=5          1200bps

        S37=6          2400bps

        S37=7          4800bps

        S37=8          7200bps

        S37=9          9600bps

       S37=10          12000bps

       S37=11          14400bps

       S37=12          16800bps

       S37=13          19200bps

       S37=14          21600bps

       S37=15          24000bps

       S37=16          26400bps

       S37=17          28800bps

       S37=18          31200bps

       S37=19          33600bps

                                 DEBUGGING

  Type:           Register

  Format:        AT [cmds] S43=n [cmds]

  Default:       1

  Range:         0-1

  Description:   Controls the auto modem for debugging only

                             SLEEP MODE TIMER

  Type:          Register

  Format         AT [cmds] S89=n [cmds]

  Default:       10

  Range:         0, 5-255

  Description:   Controls the sleep mode timer

