
BOCA RESEARCH, INC.

BOCA WINSTORM 56K PCI MODEM

Card Type                        Modem, Fax
Chip Set                         Unidentified
I/O Options                      microphone, speaker out
Maximum Modem Rate               56Kbps
Maximum Fax Rate                 14.4Kbps
Data Modulation Protocol         Bell 103A/212A

                                 ITU-T V.21, V.22, V.22bis, V.23, V.32,
                                 V.32bis, V.34, V.90, K56 flex
Fax Modulation Protocol          ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression     MNP2-4,MNP5, V.42, V.42bis
Fax Class                        Class I & II
Data Bus                         32-bit PCI
Card Size                        Half-length, half-height card

[Image]

                                CONNECTIONS

         Function            Label            Function             Label

  Microphone                     CN1       Speaker out              CN2

                   SUPPORTED COMMAND SET

                     Basic AT Commands

  AT, A/

  A, E, H, L, M, O, Q, S, T, V, X, Z

  &C, &F, &P, &V

                   Extended AT Commands

  %Q

                        S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12

                     Special Commands

  +MS

  Note: See MHI Help File for full command documentation.















                         Proprietary AT Command Set

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DL             Re-dial last number

          DP             Pulse dialing enabled

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

        D"WXY"           Optional method of denoting telephone numbers.
                         Letters enclosed in quotes are interpreted as
                         numbers according to the system found on a
                         telephone keypad.

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D&             Wait for credit card bong before continuing with
                         the dial string

          D^             Toggles calling tone enable/disable

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D$             Wait for prompt tone detection function enabled.
                         Waits for prompt tone for amount of time
                         specified by the S7 command.

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports modem model and speed

       I1        Reports ROM checksum

       I2        Tests and reports ROM checksum

       I3        Unidentified

       I4        Unidentified

       I5        Unidentified

       I6        Reports data connection information

       I7        Reports manufacturer and model information











                         DATA TERMINAL READY (DTR)

  Type:                  Configuration

  Format:                AT [cmds] &Dn [cmds]

  Description:           Selects modem response to DTR

        Command                              Function

          &D0            Modem does not respond to DTR

          &D1            Modem goes to command mode after DTR goes is off

          &D2            Modem goes to command mode and disconnects
                         (hangs up) after DTR goes off; Auto-Answer is
                         disabled.

                                GUARD TONE

  Type:           Configuration

  Format:         AT [cmds] &Gn [cmds]

  Description:    Commands the modem to transmit a guard tone in
                  V.22/V.22bis

            Note: Used primarily for international data transmission

    Command                              Function

      &G0         Guard tone disabled

      &G1         Guard tone disabled

      &G2         1800Hz guard tone enabled

                           STORE ACTIVE PROFILE

  Type:            Configuration

  Format:          AT [cmds] &Wn [cmds]

  Description:     Writes the values for the active profile into the
                   non-volatile RAM

                            Extended AT Commands

                 AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

  Type:          Configuration

  Format:        AT [cmds] %En [cmds]

  Description:   Controls auto-retrain mode and fallback/fall-forward

    Command                              Function

      %E0        Auto-retrain disabled

      %E1        Auto-retrain enabled

                                   DSVD

  Type:          Configuration

  Format:        AT [cmds] SSEn [cmds]

  Description:   Controls the DSVD

    Command                              Function

     -SSE0       Disabled

     -SSE1       Enabled



                            Special AT Commands

                             DATA COMPRESSION

  Type:                  Configuration

  Format:                AT [cmds] +DSn,m,o,p [cmds]

  Description:           Controls the data compression

        Command                              Function

          n=0            Negotiated; no compression

          n=1            Data compression both directions, accept any
                         direction

          m=0            Do not disconnect if V.42bis is not negotiated
                         by the remote modem as specified in n

           o             Specifies the maximum number of dictionary
                         entries (2048 entries) which should be
                         negotiated

           p             Specifies the maximum string length (32bytes) to
                         be negotiated

                          ERROR CONTROL REPORING

  Type:                  Configuration

  Format:                AT [cmds] +Ern [cmds]

  Description:           Controls the whether or not the extended-format
                         intermediate result code is transmitted from the
                         modem to the DTE

        Command                             Function

         +ER0            Disabled

         +ER1            Enabled

                            LOCAL FLOW CONTROL

  Type:                  Configuration

  Format:                AT [cmds] +IFCn [cmds]

  Description:           Controls the modem local flow control

        Command                              Function

         +IFC0           No flow control

         +IFC1           XON/XOFF on transmitted data

         +IFC2           Circuit 133

         +IFC3           XON/XOFF on transmitted data with XON/XOFF
                         characters being passed through to the remote
                         modem.

                           LOCAL RATE REPORTING

  Type:                  Configuration

  Format:                AT [cmds] +ILRRn [cmds]

  Description:           Controls whether or not the extended-format
                         information text is transmitted from the modem
                         to the DTE

        Command                             Function

        +ILRR0           Disabled

        +ILRR1           Enabled

                        MANUFACTURER IDENTIFICATION

  Type:          Configuration

  Format:        AT [cmds] +GMIn [cmds]

  Description:   Reports the modem manufacturer

                           MODEL IDENTIFICATION

  Type:          Configuration

  Format:        AT [cmds] +GMMn [cmds]

  Description:   Reports the modem model identification

                           MODULATION REPORTING

  Type:          Configuration

  Format:        AT [cmds] +MRn [cmds]

  Description:   Controls the modulation reporting

    Command                              Function

      +MR0       Disabled

      +MR1       Enabled

                          REVISION IDENTIFICATION

  Type:          Configuration

  Format:        AT [cmds] +GMRn [cmds]

  Description:   Reports the modem version, revision level, or date.

                             VIDEO READY MODE

  Type:          Configuration

  Format:        AT [cmds] +Hn [cmds]

  Description:   Controls the video ready mode

    Command                              Function

      +H0        Disable video ready mode

      +H16       Enabled video ready mode

                            S(status) -REGISTERS

                         FLASH DIAL MODIFIER TIME

  Type:                Register

  Format               AT [cmds] S29=n [cmds]

  Default:             70

  Range:               0-255

  Unit:                .01 second

  Description:         Time the modem will go on-hook upon receiving the
                       ! dial modifier in dial string.

