
ACTIONTEC ELECTRONICS, INC.

DESKVOICE ADVANTAGE

Card Type                    Modem, Fax
Chip Set                     Unidentified
Maximum Modem Rate           56Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Unidentified
Fax Modulation Protocol      Unidentified
Error Correction/Compression Unidentified
Fax Class                    Unidentified
Data Bus                     16-bit ISA
Card Size                    Half-length, half-height card

[Image]

                                CONNECTIONS

         Function            Label            Function             Label

  Line out                        CN1       Line in                 CN2

                       SUPPORTED COMMAND SET

                         Basic AT Commands

  AT, +++, A/

  A, C, E, H, M, P, Q, T, W, Z

  &C, &G, &V, &Z

                       Extended AT Commands

  \A, \B, \J, \K, \T, \X

                            S Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S91, S92

  Note: See MHI Help File for full command documentation.





















                         Proprietary AT Command Set

                            AUTO-MODE DETECTION

  Type:                  Configuration

  Format:                AT [cmds] Nn [cmds]

  Description:           Selects various options for the automatic
                         detection and negotiation of protocols during
                         the handshake process if the modem is
                         communicating with a remote modem of dissimilar
                         speed.

        Command                              Function

          N0             Auto-mode detection disabled

          N1             In originate mode, handshake begins at line
                         speed designated by the S37 register. Modem can
                         shift to a slower speed if necessary.

                         In answer mode, handshake attempted with the
                         following protocols in order - V.FC, V.32bis,
                         V.32, V.22bis, V.22 or Bell 212, V.21, and Bell
                         103

                              AUXILIARY RELAY

  Type:          Configuration

  Format:        AT [cmds] &Jn [cmds]

  Description:   Selects the auxiliary relay option

    Command                                Mode

      &J0        Auxiliary relay never closed

                          COMMUNICATION PROTOCOLS

  Type:                  Configuration

  Format:                AT [cmds] Bn [cmds]

  Description:           Selects the communication protocol for data
                         calls

            Note: The B command allows the simultaneous selection of more
            than one suffix, enabling multiple protocols.

        Command                              Protocol

          B0             ITU-T V.22 at 1200bps

          B1             Bell 212A at 1200bps

          B2             Unselect V.23 reverse channel

          B3             Unselect V.23 reverse channel

          B15            V.21 at 300bps

          B16            Bell 103J at 300bps

                            COMMUNICATIONS MODE

  Type:          Configuration

  Format:        AT [cmds] &Mn [cmds]

  Description:   Selects communications mode

    Command                                Mode

      &M0        Asynchronous mode











                            COMMUNICATIONS MODE

  Type:           Configuration

  Format:         AT [cmds] &Qn [cmds]

  Description:    Selects communications mode options

    Command                                Mode

      &Q0         Asynchronous mode, serial port speed follows connect
                  speed.

      &Q5         Buffered error correction mode

      &Q6         Buffered asynchronous mode

      &Q7         Reserved

      &Q8         MNP error control mode

      &Q9         V.42 or MNP error control mode

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected

                         DATA TERMINAL READY (DTR)

  Type:                  Configuration

  Format:                AT [cmds] &Dn [cmds]

  Description:           Selects modem response to DTR

        Command                              Function

          &D0            Modem does not respond to DTR

          &D1            Modem goes to command mode after DTR goes is off

          &D2            Modem goes to command mode and disconnects
                         (hangs up) after DTR goes off; Auto-Answer is
                         disabled.

          &D3            Modem is initialized after DTR goes off













                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DL             Re-dial last number

          DP             Pulse dialing enabled

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D^             Disable data calling tone transmission

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D$             Wait for prompt tone detection function enabled.
                         Waits for prompt tone for amount of time
                         specified by the S7 command.

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] &F [cmds]

  Description:      Sets values in active profile to values found in the
                    default profile

     Command                              Function

       &F0          Recall factory setting as active configuration

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K1        Reserved

      &K2        Reserved

      &K3        RTS/CTS flow control enabled

      &K4        XON/XOFF flow control enabled













                                  ON-LINE

  Type:           Immediate

  Format:         AT [cmds] On [cmds]

  Description:    Controls on-line command (data transmission) state
                  options.

            Note: The O command must be placed at the end of the command
            string.

     Command                             Function

       O0         On-line command mode with no retraining enabled

       O1         On-line command mode with retraining enabled

       O3         Issue rate renegotiation before returning to online
                  data mode

                            PULSE DIALING RATIO

  Type:          Configuration

  Format:        AT [cmds] &Pn [cmds]

  Description:   Selects pulse dial make/break ratio

    Command                              Function

      &P0        39/61ms at 10pps (North America)

      &P1        33/67ms at 10pps (Europe)

      &P2        39/61ms at 20pps

                            REPORT INFORMATION

  Type:              Immediate

  Format:            AT [cmds] In [cmds]

  Description:       Displays information requested

      Command                              Function

        I0           Reports modem firmware revision number and speed

        I1           Reports ROM checksum

        I2           Tests and reports ROM checksum

        I3           Reports the default speed and the controller
                     firmware version

        I4           Reports data pump firmware version

        I5           Reports the board ID: software version, hardware
                     version, and country ID

        I6           Reports OK

        I7           Reports OK

        I8           Reports OK

        I9           Reports country code

        I11          Reports diagnostic information for the last
                     connection

                        RESTORE PROFILE ON POWER-UP

  Type:               Configuration

  Format:             AT [cmds] &Yn [cmds]

  Description:        Restores a selected profile into the active profile
                      on power-up (hard reset)

      Command                              Function

        &Y0           Selects profile 0 on power-up











                                  RTS/CTS

  Type:           Configuration

  Format:         AT [cmds] &Rn [cmds]

  Description:    Selects RTS/CTS options

    Command                              Function

      &R0         CTS follows RTS in data mode; RTS is ignored in command
                  mode.

                     SELECT CALL PROGRESS RESULT CODES

  Type:                  Configuration

  Format:                AT [cmds] Xn [cmds]

  Description:           Enables selection of tone detection and
                         associated result code format options

        Command                              Function

           X0            Busy and dial tone detection disabled; result
                         codes 0 - 4 enabled.

           X1            Busy and dial tone detection disabled; result
                         codes 0 - 5 & 10 enabled.

           X2            Busy tone detection disabled, dial tone
                         detection enabled; result codes 0 - 6 & 10
                         enabled.

           X3            Busy tone detection enabled, dial tone detection
                         disabled; result codes 0 - 5, 7 & 10 enabled.

           X4           Busy and dial tone detection enabled; result
                         codes 0 - 7 & 10 enabled.

           X5            Busy and dial tone detection enabled; result
                         codes 0 - 7 & 10 enabled.

           X6            Busy and dial tone detection enabled; result
                         codes 0 - 7 & 10 enabled.

           X7            Busy and dial tone detection enabled; result
                         codes 0 - 7 & 10 enabled.

                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Lowest volume setting

       L1        Low volume setting

       L2        Medium volume setting

       L3        Highest volume setting

                           STORE ACTIVE PROFILE

  Type:            Configuration

  Format:          AT [cmds] &Wn [cmds]

  Description:     Writes the values for the active profile into the
                   non-volatile RAM

     Command                              Function

       &W0         Writes the active profile to stored profile 0

                           Extended Result Codes

                                 BLACKLIST

  Type:          Configuration

  Format:        AT [cmds] %B [cmds]

  Description:   View numbers in blacklist

                                COMPRESSION

  Type:          Configuration

  Format:        AT [cmds] %Cn [cmds]

  Description:   Selects data compression

    Command                              Function

      %C0        Data compression disabled

      %C1        V.42bis and MNP5 enabled

                               CONNECT MODE

  Type:          Configuration

  Format:        AT [cmds] \Nn [cmds]

  Description:   Controls the type of connection the modem will operate
                 in

    Command                              Function

      \N0        Normal mode enabled

      \N1        Direct mode enabled

      \N2        Reliable mode enabled

      \N3        Auto-reliable mode enabled

      \N4        V.42 reliable mode enabled

      \N5        Auto-reliable mode enabled

      \N7        Auto-reliable mode enabled

                             DATA CALLING TONE

  Type:          Configuration

  Format:        AT [cmds] -Cn [cmds]

  Description:   Controls the data calling tone

    Command                              Function

      -C0        Disable data calling tone

      -C1        Enable data calling tone









































                             DATA CALLING TONE

  Type:          Configuration

  Format:        AT [cmds] -V90=n [cmds]

  Description:   Controls the data calling tone

    Command                              Function

    -V90 = 0     V.90 disabled

    -V90 = 1     Auto Rate

    -V90 = 2     28000bps

    -V90 = 3     29333bps

    -V90 = 4     30666bps

    -V90 = 5     32000bps

    -V90 = 6     33333bps

    -V90 = 7     34666bps

    -V90 = 8     36000bps

    -V90 = 9     37333bps

   -V90 = 10     38666bps

   -V90 = 11     40000bps

   -V90 = 12     41333bps

   -V90 = 13     42666bps

   -V90 = 14     44000bps

   -V90 = 15     45333bps

   -V90 = 16     46666bps

   -V90 = 17     48000bps

   -V90 = 18     49333bps

   -V90 = 19     50666bps

   -V90 = 20     52000bps

   -V90 = 21     53333bps

                           EXTENDED RESULT CODES

  Type:          Configuration

  Format:        AT [cmds] \Vn [cmds]

  Description:   Selects extended result codes

    Command                              Function

      \V0        Extended result codes disabled

      \V1        Extended result codes enabled

      \V2        Extended result codes enabled

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] \Gn [cmds]

  Description:   Selects modem port flow control

  Note: Command performs no function; included for compatibility only











                             FLOW CONTROL TYPE

  Type:          Configuration

  Format:        AT [cmds] \Qn [cmds]

  Description:   Sets type of flow control used by modem

    Command                              Function

      \Q0        Flow control disabled

      \Q1        Bidirectional XON/XOFF flow control enabled

      \Q2        CTS flow control by DCE enabled

      \Q3        Bidirectional RTS/CTS flow control enabled

                              RING INDICATOR

  Type:            Configuration

  Format:          AT [cmds] \Rn [cmds]

  Description:     Controls the ring indicator signal

     Command                              Function

       \R0         Ring indicator signal is off after the telephone call
                   is answered

                            S(status) -REGISTERS

                            56K DIAL LINE RATE

  Type:                Register

  Format               AT [cmds] S38=n [cmds]

  Description:         Sets the maximum allowable data exchange rate
                       attempted during handshake process.

       Command                              Function

        S38=0          K56flex disabled

        S38=1          K56flex autorate

        S38=2          32000bps

        S38=3          34000bps

        S38=4          36000bps

        S38=5          38000bps

        S38=6          40000bps

        S38=7          42000bps

        S38=8          44000bps

        S38=9          46000bps

       S38=10          48000bps

       S38=11          50000bps

       S38=12          52000bps

       S38=13          54000bps

       S38=14          56000bps















                          BIT-MAPPED REGISTER S14

  Format:          AT [cmds] S14=n [cmds]

  Default:         8

  Range:           0-174

  Unit:            Bit-mapped

  Description:     Controls echo, result codes and display and dial mode

   Bit    Value                           Function

    3          0   Display result codes in numeric format

              1    Display result codes in verbose format

    6          0   10 PPS

              1    20 PPS

                          BIT-MAPPED REGISTER S21

  Format           AT [cmds] S21=n [cmds]

  Default:         48

  Range:           Unidnetified

  Unit:            Bit-mapped

  Description:     Indicates the status of command options

   Bit    Value                           Function

  4, 3         0   &D0 selected

               1   &D1 selected

               2   &D2 selected

              3    &D3 selected

    5          0   &C0 selected

              1    &C1 selected

                          BIT-MAPPED REGISTER S22

  Format           AT [cmds] S22=n [cmds]

  Default:         Unidentified

  Range:           0-255

  Unit:            Bit-mapped

  Description:     Indicates the status of command options

   Bit    Value                           Function

  6 - 4        0   X0 selected

               4   X1 selected

               5   X2 selected

               6   X3 selected

              7    X4 selected

    7          0   33/67ms at 10pps (Europe)

              1    39/61ms at 10pps (North America)

















                          BIT-MAPPED REGISTER S28

  Format               AT [cmds] S28=n [cmds]

  Default:             unidentified

  Range:               0-31

  Unit:                Bit-mapped

  Description:         Controls V.23 split speed, transmit/receive speed,
                       half duplex; and pulse dialing.

        Value                               Function

          0            Disable

        1-255          Enable

                          BIT-MAPPED REGISTER S40

  Format         AT [cmds] S40=n [cmds]

  Default:       0

  Range:         0-2

  Unit:          Bit-mapped

  Description:   Controls ETC startup autorating

    Command                              Function

     S40=0       Startup with normal autorating

     S40=1       Startup with initial rate of 4800 or below

     S40=2       Startup with initial rate of 9600 or below

                             DATA CALLING TONE

  Type:          Register

  Format         AT [cmds] S35n [cmds]

  Description:   Controls the data calling tone

    Command                              Function

     S36=0       Disabled

     S36=1       Enabled









































                              DCE LINE SPEED

  Type:                Register

  Format               AT [cmds] S37=n [cmds]

  Description:         Sets the maximum allowable data exchange rate
                       attempted during handshake process.

       Command                              Function

        S37=0          Speed of last connection

        S37=1          Reserved

        S37=2          1200/75bps

        S37=3          300bps

        S37=4          Reserved

        S37=5          1200bps

        S37=6          2400bps

        S37=7          4800bps

        S37=8          7200bps

        S37=9          9600bps

       S37=10          12000bps

       S37=11          14400bps

       S37=12          16800bps

       S37=13          19200bps

       S37=14          21600bps

       S37=15          24000bps

       S37=16          26400bps

       S37=17          28800bps

       S37=18          31200bps

       S37=19          33600bps

                        FEATURE NEGOTIATION OPTIONS

  Type:                 Register

  Format:               AT [cmds] S48=n [cmds]

  Description:          Selects active error correction and compression
                        protocols

       Command                              Function

        S48=7           Detection negotiation and XID negotiation enabled

       S48=128          Detection negotiation and XID negotiation
                        disabled, fall-back to options set in S36

                            LOCAL PHONE STATUS

  Type:           Register

  Format:         AT [cmds] S90=n [cmds]

  Description:    Sets the status of the local phone

    Command                              Function

     S90=7       Local phone on-hook

    S90=128      Local phone off-hook











                           NEGOTIATION FALLBACK

  Type:               Register

  Format              AT [cmds] S36=n [cmds]

  Description:        Controls the negotiation fallback

      Command                              Function

      S36=0, 2        Hang up

      S36=1, 3        Attempt a direct connection

      S36=4, 6        Attempt a connection at MNP2-4; if that fails, hang
                      up.

      S36=5, 7        Attempt a connection at MNP2-4; if that fails,
                      attempt a direct connection.

                                SLEEP MODE

  Type:          Register

  Format         AT [cmds] S89=n [cmds]

  Default:       10

  Range:         0, 5-255

  Description:   Controls the sleep mode timer

                         SYNTHETIC RING FREQUENCY

  Type:          Register

  Format:        AT [cmds] S33=n [cmds]

  Default:       0

  Range:         0-5

  Unit:          Unidentified

  Description:   Specifies a synthetic ring frequency

                           SYNTHETIC RING VOLUME

  Type:          Register

  Format:        AT [cmds] S32=n [cmds]

  Default:       16

  Range:         Unidentified

  Unit:          dB

  Description:   Specifies a synthetic ring volume with implied minus
                 sign

